Dimensions of the Flexco Steps Part # SMFP-4400

Question

Question:

will changing my 3 steps to 4 steps on my new passport elite trailer make the steps less steep?

asked by: Chuck

0

Expert Reply:

That is hard to say, but what you can do is check out the dimensional picture I attached for the Flexco Steps part # SMFP-4400 and compare them to what you have to see how they would compare to what you currently have.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hickory Springs does offer a 4 step model of their RV pull out steps with the part #SMFP-4400. These have the same dimensions as the triple step as well as same step design so it's exactly what you are wanting.

view full answer...

Answer 2

Manual RV steps #SMFP-4400 could work for you. This is a 4-step unit that is 28-1/8 inches wide overall and 12 inches deep (front to back) and 18-1/2 inches tall. None of the other 4-step options are as close in the measurements of what you have now.…

view full answer...

Answer 3

I called my contact at Lippert about the Manual Pull-Out Steps For RVs, part #SMFP-4400 they said the capacity is 300 lbs.

view full answer...

Answer 4

Normally the SAE number isn't a reliable way to pick out replacement lenses, but we know that the #A32RB is the correct replacement for a lens marked SAE-A-P2-DOT-02 like what you have. For an all new assembly you'd want the part #MC32RB.

view full answer...

Answer 5

I have another option, But you are correct that the Aries Pro Series Grille Guard with Mesh LED Cover Plate #AAP1053, and Blue Ox Base Plate Kit #BX1139 will not both be able to be installed on your 2021 Jeep Wrangler as they both mount to the frame…

view full answer...

Answer 6

Your G6A-7 is an Atwood water heater with a 1/2" drain plug. If you have aluminum threads I recommend the Camco RV Water Heater Anode Rod w/ Drain - 1/2" Diameter x 4-1/2" Long Item #CAM11533. This is an aluminum plug with an anode rod…

view full answer...

Answer 7

Yes, the Ventline Pinnacle Ducted RV Range Hood with Light #VE98SR can replace your existing High Pointe range hood. This has the same dimensions at 20" wide x 18" deep x 4-3/4" tall. There will be a small difference in the vent…

view full answer...

Answer 8

The closest RV step we offer to 27 inches in width is the Flexco triple step #SMFP-3200L that measures 27-1/8 inches in total width. You might need the outriggers part #LC301704 to move the brackets out to install the steps if yours is 27 inches…

view full answer...

Answer 9

The replacement motor for the Greystone RV Range Hood with Light - 12V - 24" Wide - Black Item #324-000087 is the Replacement 12-Volt DC Fan Motor for Ventline RV Range Hood Item #BVD0218-00. If you also need to replace the fan blade the correct…

view full answer...

Answer 10

If the mounting location for your RV steps is 27 inches wide we have steps that will work for you. I recommend the Stromberg Carlson RV Stairs, part #SMFP-4400. These steps measure 27-inches wide overall, and 12-inches deep (front to back) and 18-1/2…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Dimensions of the Flexco Steps Part # SMFP-4400

Product Page this Question was Asked From

Continue Researching