Replacement 3-Step Manual RV Steps with 4-Step Manual RV Steps

Question

Question:

We want to replace Flexco manual 3 steps with 4 steps on our 2015 Silverback by Forest River. Box dimensions are 12inch Deep 27inch Wide 16 3/4inch High. Do you have steps which would fit ?

asked by: Karen P

0

Expert Reply:

Manual RV steps # SMFP-4400 could work for you. This is a 4-step unit that is 28-1/8 inches wide overall and 12 inches deep (front to back) and 18-1/2 inches tall. None of the other 4-step options are as close in the measurements of what you have now. the 4-step model will hang down at least 4 inches more than the 3-step model when the steps are extended.

expert reply by: Michael H

0

Dimensions of Flexco Manual Pull-Out Quad Steps for RVs
(click to enlarge)

Answer 1

Hickory Springs does offer a 4 step model of their RV pull out steps with the part #SMFP-4400. These have the same dimensions as the triple step as well as same step design so it's exactly what you are wanting.

view full answer...

Answer 2

I called my contact at Lippert about the Manual Pull-Out Steps For RVs, part #SMFP-4400 they said the capacity is 300 lbs.

view full answer...

Answer 3

That is hard to say, but what you can do is check out the dimensional picture I attached for the Flexco Steps part #SMFP-4400 and compare them to what you have to see how they would compare to what you currently have.

view full answer...

Answer 4

The Adjustable Width Trailer Hitch Receiver for RVs part #13703 is what I recommend for a Grand Design Solitude. It features a 3,500 lb gross trailer weight capacity and 350 lb tongue weight rating. This will be the most offered for a trailer as…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Replacement 3-Step Manual RV Steps with 4-Step Manual RV Steps

Product Page this Question was Asked From

Continue Researching