How Does Curt Coupler Repair Kit # C25194 Assemble

Question

Question:

does the big spring go inside of the coupler?

asked by: Jerry

1

Helpful Expert Reply:

It certainly does. I've provided a diagram for a different coupler repair kit that will show you exactly how the latch assembles and what goes where.

The threaded bolt from the handle inserts into the coupler. From underneath, slide on the spring, the jaw and the square plate, followed by the tension spring and the lock nut.

expert reply by: Mike L

1

click to enlarge

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

The main reasons why trailer tires blow out is heat generated from under inflated tires and overloading the tires. Trailer tires should be inflated to the maximum psi indicated on the tire. A tire in the same size but with a higher ply rating would…

view full answer...

Answer 3

There is a nut on the underside of the coupler latch of your Posi-Lock style coupler that will allow you to tighten the mechanism to the ball so that you can remove that movement.

view full answer...

Answer 4

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 5

I wish we still had access to the Shelby replacement parts but since they aren't currently around anymore there's nothing we offer that I can guarantee will fit. I recommend instead getting a new coupler such as #CT-3001-Z. I've left a…

view full answer...

Answer 6

We still haven't and I wouldn't hold my breath waiting to find out. Most of the time when customers try out stuff they don't end up letting us know if it ended up working out or not. I'd suspect no though. I recommend simply replacing…

view full answer...

Answer 7

Typically the 7th digit of a trailer VIN is the year the trailer was manufactured. I attached a picture that shows a VIN decoder for trailers for you to check out as well. You can also give the VIN to the trailer manufacturer and I am sure they will…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

How Does Curt Coupler Repair Kit # C25194 Assemble

Product Page this Question was Asked From

Continue Researching