Replacement Bulkhead Header Seal for Truxedo Lo Pro Tonneau Cover

Question

Question:

Hello, I have a Truxedo Lo Pro QT cover installed on my Nissan Frontier. I recently had to remove the cover and would like to replace the bulkhead seal before I put it back on. Do you sell a replacement bulkhead seal that would work, either from Truxedo or another brand? Thank you

asked by: Matthew T

0

Expert Reply:

We do have the exact part you are looking for to replace the bulkhead seal - also called the header seal - for your Truxedo Lo Pro tonneau cover.

What you need is the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover # TX1704787.

expert reply by: Kyle S

0

Answer 1

The correct replacement bulkhead weather seal for your TruXedo Lo Pro Cover is the Replacement Header Seal for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX1704787. This seal measures 5-1/2' long and 1-1/2" wide.

view full answer...

Answer 2

I went to our warehouse and took a look at the Replacement Header Seal for TruXedo Lo Pro QT, part #TX1704787. You will need to remove the seal you currently have by removing the plug on the end of the header. You may need to use something like a…

view full answer...

Answer 3

Thanks for providing that number/date code! The correct replacement tarp for your TruXedo Lo Pro soft tonneau cover is part #TX577601-CVR. Your cover uses the same seal at the front of the bed and at the tailgate. That replacement part is…

view full answer...

Answer 4

Could you get me pictures of your tonneau cover so that I can identify it possibly? And which exact seals do you need?

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Bulkhead Header Seal for Truxedo Lo Pro Tonneau Cover

Product Page this Question was Asked From

Continue Researching