Custom Fit Replacement Towing Mirrors for a 2012 GMC Sierra

Question

Question:

Will these mirrors replace the factory non-tow mirror for GMC 2012 Duramax? Im not sure if the main bracket is different for the tow mirrors or not. Thanks

asked by: Brandon

0

Expert Reply:

Yes, you can install K-Source custom towing mirror # KS62094G on your 2012 GMC Sierra even if the truck did not come with factory towing mirrors. This mirror has electric operation, heat, and turn signal functions. If your factory mirrors did not have one or any of these options then by installing the towing mirrors will not give you those functions.

The set, driver and passenger side, is # KS62093-94G. I have linked a video review for you.

expert reply by: Michael H

0

Answer 1

The SAE number isn't the best way to pick out replacement lenses for trailer taillights since that isn't actually a part number. However, I did find a replacement lens with SAE P2A 01 DOT on the front of it. Check out the part #A44RB. If this…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 4

Hey Jason, I spoke with Furrion and they stated that the Furrion Chill Cube is OEM only currently and should be released to the aftermarket distributors later on this year (2024), but there is no solid date. That says to me that they're probably…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Since the bolt holes line up vertically and horizontally you'll be able to bolt the Trailair Air Ride 5th Wheel King Pin - Leland 7920 #UF35-946208. This specific pin box actually has an 18" king pin to first set of bolt holes measurement…

view full answer...

Answer 7

Though safety chains to do not come with a Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter such as RP94623 they are available by using the Tow Ready Safety Chain Kit #49150. If you look at the accompanying photo you can see exactly…

view full answer...

Answer 8

The mounting holes of the Swing Out Extension Brackets part #LC182496 that you referenced are for the side that attaches to the jack itself and not the portion that attaches to the camper. You'd need to attach these to the L-bracket on the camper…

view full answer...

Answer 9

Yes the Happijac swing out bracket kit part #LC182496 does work with your camper with a set of Happjac truck camper jacks and would also work/be needed for your 2021 Ram truck that is a dually.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I contacted the Rep at Happijac to inquire on your question of the HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks, #HJ54FR. His response was that yes, you can "stack" the extensions. There is however a point…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...