Sway Control System Recommendation for 30 Toy Hauler 13,000 LBS

Question

Question:

I currently have a Draw Tite trailer sway control for my trailer. Not sure which model it is but it appears to be pretty worn out as it is not controlling trailer sway very well any longer. Is there a re-build kit available for these units or are they a throw away and replace when worn? I have a 30foot toyhauler that when loaded is approx 13,000lbs. What replacement unit would you recommend? The Curt unit seems to be more cost effective. Thanks

asked by: Kurt M

0

Expert Reply:

The wear that you are experiencing on your sway control unit could be due to the fact that only one unit is being used on your trailer.

Since your toy hauler is 30' long, we recommend using 2 of the Reese Friction Sway Control Kits, # 83660. This unit reduces trailer sway caused by crosswinds and traffic for improved stability and increased towing safety. It's also a customer favorite because it is economical, very easy to use, and can be installed on the left or right side of the trailer. I have attached an installation video for you.

Draw Tite does not offer a re-build kit for the sway control unit so it sounds like it is probably time for a replacement.

expert reply by: Leah S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, you can use the Reese Friction Sway control part #83660 without a weight distribution system. You would just need to use the tab part #RP26003 on the ball mount as well.

view full answer...

Answer 5

Basically, one friction-style sway control can be used for trailers with up to 6,000-lb GTW. If your trailer's GTW is between 6,000 lbs and 10,000 lbs, you will need two sway-control units, one on each side of the trailer. You will also want to…

view full answer...

Answer 6

Yes, it will! The Reese Pro Round Bar Weight Distribution item #RE34FR works with tongue weights between 200 lbs - 600 lbs so it will be perfect for your 3,500 lbs trailer. The Curt Trailer Hitch item #C13200 you have is also rated to be used with a…

view full answer...

Answer 7

Good morning, Crystal. We can certainly provide you with three of the TCL65 Trimax Trailer Wheel Chock and Lock #TMX75FR. That said, we do not offer a "keyed alike" option for these locks, nor can we guarantee a specific key number. So, we…

view full answer...

Answer 8

Hello Kendall. The K-Source Universal Towing Mirrors #KS69ZR are going to be your best bet for the 2022 Toyota Tundra Limited. We have double checked with the manufacturer and confirmed that they will fit the Limited models with full chrome or…

view full answer...

Answer 9

To get maximum benefits from the sway control, a series of road tests should be taken with the loaded trailer. A great starting point you will want to loosen the tension bolt till it no longer makes contact with the unit, now tighten it up right till…

view full answer...

Answer 10

For your 2024 Toyota Sienna Platinum you will need a 7-way connection along with the brake controller itself. I recommend the following: -Curt Powered Tail Light Converter #C59236 -Universal Installation Kit for Trailer Brake Controller #ETBC7…

view full answer...