Availability of Pinion Gear for Ventline Ventadome Roof Vent Model # V2119

Question

Question:

Can I get just the pinion gear only for this ventline vent...?

asked by: Jeff O

0

Expert Reply:

The only stand-alone replacement plastic gear for Ventline Ventadome Trailer vents that we offer is part # BVD0121-00. This part works with roof vent model V2119.

expert reply by: Adam R

0

Answer 1

The Replacement Gear Motor with Pinion Gear for Ventline Ventadome Trailer Roof Vent #BVB0601-00 or just the Replacement Plastic Gear for Ventline Ventadome Trailer Roof Vent - Dome Motor Gear #BVD0121-00 is what you need to lift the dome.

view full answer...

Answer 2

If the lift motor on your Ventline #V2119-601-00 runs when you try to operate it then it sounds like you need the Replacement Plastic Gear #BVD0121-00 which operates the lift arm. To replace the lift motor you need the Replacement Gear Motor with…

view full answer...

Answer 3

The Replacement Gear Motor with Pinion Gear #BVB0601-00 is the correct replacement for the Ventline Ventadome roof vent model V2119. It sounds like you also need the Replacement Operator, Knob and Screw for Ventline Ventadome Trailer Roof Vents…

view full answer...

Answer 4

Appreciate the photos and based on those we do have what you are needing, which is the gear motor and gear for your Ventline V2119 roof vent: - Replacement Gear Motor with Pinion Gear #BVB0601-00 - Replacement Plastic Gear #BVD0121-00

view full answer...

Answer 5

It sounds like you have the Ventline Ventadome Roof Vent w/ 12V Fan #V2119-601-00. This Ventline roof vent has a powered lift arm assembly. The correct arm assembly replacement that you would need would be the Replacement Operator, Knob and Screw…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Availability of Pinion Gear for Ventline Ventadome Roof Vent Model # V2119

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching