How to Determine Hanger Spacing Using 25-1/8 Inch Long Trailer Leaf Springs

Question

Question:

What is the distance of hangers on 25 1/8inch tandem axel trailer

asked by: Clay M

1

Helpful Expert Reply:

It all depends on the spring being used, the shackles, and the equalizers among other things. There are some suggested hanger spacing measurements but really you would mock it all up first before permanently welding the hangers in place.

For example, if you used suspension kit # APT5 and spring # e54SR that is 25-1/8 inches long then the distance between the front and center hangers and between the center and rear hangers is 29-1/2 inches. That would create an axle spacing of 33-1/2 inches.

Shorter or longer equalizers or shackle straps would change all of that. If you can tell me the springs you are using or the capacity of each axle I can make some suggestions for you but ultimately it would be just a guideline and not a set in stone set of measurements.

expert reply by: Michael H

1

Answer 1

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 8

Trailer manufacturers don't usually keep a record of parts like these that they install at the factory, so I cannot be sure as to the exact length of the shackle strap that would have come originally on your trailer. With this in mind, a 3-1/8…

view full answer...

Answer 9

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Answer 10

To slightly lower your trailer that has had an "axle flip" kit installed you would want to use slightly shorter shackle straps, not longer ones. Shorter shackles will let the axle rest closer to the trailer frame, which lowers the trailer…

view full answer...

Answer 11

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 12

It is not uncommon for the trailer hangers on a tandem axle trailer to be all the same size or for there to be different sizes that can be 1-1/2 to 2 inches different in height when you compare the center hanger to the front and rear. For example,…

view full answer...

How to Determine Hanger Spacing Using 25-1/8 Inch Long Trailer Leaf Springs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching