Clearance Using a Swagman XTC4, # S64665 on a 2008 Toyota Rav4

Question

Question:

Is there sufficient clearance from the spare tire on a 2008 Rav4 Limited?

asked by: Ed

0

Expert Reply:

On your 2008 Toyota Rav4 Limited, you will need to measure from the center of the hitch pin hole to the furthest point on the rear of the vehicle, in this case, the spare tire. If that measurement is greater than 12-3/4 inches, the 4 Bike Rack for 2 inch Trailer Hitches, Wheel Mount - Swagman XTC4, # S64665, will not fit.

expert reply by: Michael H

0

Answer 1

For a wall mounted storage rack the Swagman X Mount part #S80940 would work well to store your Swagman XTC4 bike rack #S64665. I attached a review video an install instructions for this rack for you to check out as well.

view full answer...

Answer 2

It sure will! The Draw-Tite Max Frame Trailer Hitch Receiver #DT92MR you were looking at was designed specifically for the 2021 Ford Mustang Mach-E. This hitch has a 350lb tongue weight rating and 3500lb trailer weight rating making it a perfect…

view full answer...

Answer 3

I spoke with both Draw-Tite and Curt about a hitch for your 2022 Ford Mustang Mach-E GT and I did come up with an option for you. The Draw-Tite #DT92MR has not yet been confirmed to fit, but the Curt #C77ER has. Though there will be no drilling for…

view full answer...

Answer 4

That's a good question, and there is one option I do like better for your 2021 Ford Mustang Mach-E between the Curt #C77ER and Draw-Tite #DT72GR hitches, and that's the hitch from Curt, which is the following part number: - Curt Trailer Hitch…

view full answer...

Answer 5

There are a couple options currently available for the 2021 Ford Mustang Mach-E. There is the Curt Trailer Hitch Receiver, #C77ER and the Draw-Tite Max-Frame, #DT92MR. Each of these options install in a similar way and do so without the need for…

view full answer...

Answer 6

As we haven't had the chance to install either the Curt #C77ER or the Draw-Tite #DT92MR on a 2021 Mustang Mach-E, I went out and measured from the center of the first bolt hole to the end of the receiver opening on both hitches. The Curt will sit…

view full answer...

Answer 7

Unfortunately, it does not appear that you can install a traditional aftermarket roof rack on your Ford Mustang Mach-E. It does not matter if you have the 2021 or the 2022. There is one option left, if you prefer carrying your items on the roof of…

view full answer...

Answer 8

The Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) #Y07235 is the lock you are seeking. It is designed to work with the Replacement Hitch Bolt, Nut and Clip for Yakima Bike Racks and DryDock Load Assist - 2" Hitches…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...