Will Draw-Tite Front Mount Trailer Hitch # 65024 Fit 2000 Ford Ranger 4x4

Question

Question:

2000 Ford Ranger 4x4 stepside 4dr Curt front hitch #C31063 does it fit? It says not an exact fit when queried on your web site. 3.0 l flex engine if it helps.

asked by: Jay C

0

Expert Reply:

The CURT Front Mount Trailer Hitch Receiver, # C31063, was designed specifically for the 2000 Ford Ranger. This custom fit hitch features bolt-on installation with no welding required.

expert reply by: Leah S

0

Answer 1

I checked with my contact at Curt and they said that the Curt front-Mount Hitch, part #C31063 does require some trimming to install on your Ranger XLT. I have attached the installation instructions for you to check out.

view full answer...

Answer 2

I spoke with my contact at Curt and he provided a picture to show what to look for when it comes to determining whether your 2000 Ford Ranger has the front crossmember. You will see his picture off to the right. If your Ranger DOES NOT have a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Will Draw-Tite Front Mount Trailer Hitch # 65024 Fit 2000 Ford Ranger 4x4

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching