Can Brophy D-Ring Tie Downs # SR15-C be Welded Rather Than Bolted on as Intended
Question:
Hi, I own a 96 Ford F250 with a ladder rack. The rack is mounted to 2inch X 3inch angle iron. I want anchors welded bracket sits vertical to the 2inch side which sits on the inside of the truck bed. Can the bracket be cut to fit, from 3 1/2inch to 2, then welded. The weld style brackets are much too large overkill. Thanks
asked by: Steve H
Expert Reply:
The Brophy D-Ring Tie Downs # SR15-C that you referenced is intended for bolt-on installation. Its 5000-lb capacity rating is based on this intended installation method. However, you certainly could cut down their length from 3-1/2 to 2-inches and weld them into place but you will need to be careful to do the welding in a well-ventilated area since zinc-plated material can give off fumes that could be harmful to breathe.
Also be aware that the finish of the welded parts will be discolored from the welding process and that in this non-standard installation the final capacity of the D-ring will be unknown and could be reduced from its 5K rating.
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor - Bolt-On - 3-1/2" Wide - Surface Mount - 1,600 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 1600 lbs
- D-Ring
- Surface Mount - Bolt-On
- Brophy
more information >
Continue Researching
- Shop: Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2" Ball - Weld On - 10K
- Shop: Buyers Products Weld-On Safety Chain Retainer For 5/16" Chain
- Video: Review of Demco A-Frame Trailer Coupler - Standard Coupler - DM14791-97
- Video: Bulldog A-Frame Trailer Coupler - Standard Coupler - BD028288 Review
- Shop: 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
- Shop: CE Smith Tie-Down Bracket for Boat Trailers - Galvanized Steel - Bolt On - Qty 1
- Shop: Laclede 27" Long Trailer Safety Chain w/ 7/16" Hook - 1,250 lbs Weight Capacity - Qty 1
- Shop: Buyers Products Weld-On Safety Chain Retainer For 3/8" Chain
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Q&A: Where do I Install D-Ring Tie Downs on a 6x10 Wood Bed Utility Trailer
- Q&A: Can an Electric Trailer Winch be Wired to Run Off of the Towing Vehicle Battery
- Video: Bulldog Axle and Ratcheting Tie Down Straps with Bag Review
- Q&A: Size of Hole Saw to Use to Install the Recessed Trailer D-Ring Tie Down RR5K
- Q&A: Is 3/4 Inch Plywood Floor Adequate for D-Ring Tie Down Anchors with Backing Plate for 3,000 lb Car
- Shop: Trailer Hitch
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Video: Choosing the Right Trailer Wiring
- Search Results: 68149
- Shop: Fifth Wheel Hitch
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Q&A: How to Power Trailer Dome Light When Not Connected to Tow Vehicle
- Shop: Brake Controller
- Search Results: dust caps