Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
Part Numbers: C74VV,C51458
Retail:$161.30
Our Price: $108.96
You Save: $52.34
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
part number: C74VV
A simple LED display and a pinch-trigger manual override make this time-delayed brake controller easy to read and easy to use. Installation is quick and simple with no mounting restrictions. Activates brakes with a preset intensity.
Features:
- Brake controller activates trailer brakes with preset intensity
- Adjustable power output control lets you select the amount of braking force
- Rocker switches located on left front of module for easy access
- 10 Gain settings and 9 load settings allow you to adapt to various driving conditions
- Select a higher setting for harder braking and lower for more gradual braking
- Pinch-trigger manual override is within easy reach for controlling trailer sway or stopping in emergencies
- Simple LED display shows the amount of power output
- Self-diagnostics monitor trailer connection and check for shorts
- LCD display shows power adjustments in 1.0 increments
- Brightness is adjustable for optimal visibility
- Auto-sleep mode prevents battery drain after 5 minutes of idle time
- Quick and easy installation with no mounting restrictions
- No need to mount level - install anywhere at any angle
- Included mounting bracket and hardware designed to hold brake controller flush against the dash
- Plug-in, vehicle-specific brake control adapter (sold separately) available for select vehicles to reduce installation time
Specs:
- Application: trailers with up to 3 axles (6 brake assemblies)
- Compatible with low-volt, PWM, ABS, cruise control, and electric-over-hydraulic trailer brakes
- Dimensions: 4" long x 3-1/8" wide x 1" thick
- Limited lifetime warranty
Gain Adjustment
Gain control lets you set the maximum amount of power that will be applied to your trailer's brakes, adjusting in increments of 1. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to go as high as you can without the trailer brakes locking up. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes. To get more power to your brakes, press the left-hand upper rocker switch. To decrease the gain, press the lower switch. When you make your adjustment, the gain setting will show on the LED screen for 5 seconds as a series of bars and then go into sleep mode to reduce drain on the battery.
Load Control
Once you have the gain set, you can fine-tune your braking by adjusting the load control on a scale of 1 to 9. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. Load control can get the braking power to your trailer faster and with more intensity so that it doesn't push your tow vehicle forward. If your vehicle takes too long to come to a stop, increase the setting by pressing the right-hand upper rocker switch. If it stops too abruptly, decrease the setting by pressing the lower switch. You can alter the setting to suit your driving preferences or to improve handling based on changing road conditions or varied trailer loads.
Pinch-Trigger Manual Override
The Venturer comes with a easy-to-reach, pinch-trigger manual override, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push in the trigger. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
LED Display
The LED display on the Venturer is large and easy to read at a glance. It will show you what setting the brake controller is on as well as give you information for troubleshooting. You can adjust the screen brightness or trigger night mode so it won't glare obnoxiously on your dash. Press the control button to cycle through the different modes, shown as a bar - keeping it simple.
Quick Installation
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, so long as you can still easily access the controller and the manual override. The included bracket is designed to mount the brake controller flush to the dash so it takes up almost no space at all.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Time-Delayed Braking
The Curt Venturer NEXT comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the Venturer. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. Both the amount of braking power (gain) and rate of application (load) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
51116 Curt Venturer NEXT Time Based Trailer Brake Control - 1 to 3 Axles
Replaces Curt 51110
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
part number: C51458
Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port behind your vehicle's dash.
Features:
- Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
- No cutting or splicing required
- Custom connectors plug into the built-in port underneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible with time-delayed and proportional brake controllers from Curt
- Brake controller must have built-in plug for adapter to connect - will not work on controllers with pigtail wiring harnesses
- 2' Long, 12-gauge wires have protective covering to deter damage
- Limited 1-year warranty
Installation of Curt Brake Controller Adapter
To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. When this is done, a port is installed at your dash so that you can easily plug in a brake controller.
This adapter plugs into the connector underneath your vehicle's dashboard, located to the right of your steering wheel.
No hardwiring is required to install this adapter. After you plug it into your vehicle's connector, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.
51458 Curt Quick Plug Brake Control Adaptor Harness
Replaces 51439
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Product did not meet expectations
- Alternate product found
- Defective
Customer Reviews
Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed - C74VV
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In - C51458
Average Customer Rating: 4.8 out of 5 stars (136 Customer Reviews)
A simple LED display and a pinch-trigger manual override make this time-delayed brake controller easy to read and easy to use. Installation is quick and simple with no mounting restrictions. Activates brakes with a preset intensity. Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in port behind your vehicle's dash.by: John 04/13/2024
Installed but not used with a trailer yet, easy instruction and appreciate the extra hardware for the installation.
Compact and not intrusive. Decided to use the adhesive tape included and taped under the dashboard L of the steering wheel.
by: Craig 06/21/2024
This break controller was easy to install and
Works grat.
by: Robert 03/24/2024
Adapter was the right part for the brake controller.
by: Mike 02/09/2024
This is an excellent adapter for trailer break
by: Jed02/09/2024
worked as promised - made it easier to pull a4 place snowmobile trialer
by: Kenneth 03/18/2023
Easy install. Perfect fit
by: Brian04/21/2021
Great controller! Easy to adjust even on the fly. I had the controller adjusted a little aggressive and as I was trying to get out of Buffalo to go south for the winter we ran into some snow accumulation and was able to quickly dial back the controller to avoid locking up on thick snow covered roads. Literally a potential disaster! Very happy with the controller
by: Jason 02/23/2024
Slimmer than most of the others. Easy install with the additional pigtail.
by: Shea06/17/2024
2021 Ram 1500 Classic
Great little plug and play. Great customer service!
by: Michael04/18/2024
Works like it should
by: Markus08/18/2019
This harness made for a clean, splice-free install. I used this with a Jeep Gladiator which requires swapping the black and blue wires in the gray connector. The Gladiator is such a new truck, I could not find a good cross reference for the exact harness for a Curt Spectrum controller. I’m sure they have one by now or will very soon. I didn’t bother calling etrailer, I knew I could make this harness work. The wire swap took less than a minute, once you see the pin latches. Well worth the money to have a solid and clean install.
Rachael H.
8/22/2019
Curt does offer a wiring harness for the 2020 Jeep Gladiator and it is available as part # C51459. This harness has the correct plug configuration for the Gladiator and does not require swapping the black and blue wires.
Helpful Links
by: Joel03/11/2023
Everything was plug and play. Installing it was straight forward after viewing instructions.
by: Metal190503/08/2024
Fit and worked
by: Dominick P.09/25/2019
It's very well made and would be simple to use, except two of the wires were switched. We used this with a 2018 Jeep Wrangler JL, but apparently they are switched on newer Dodge trucks too. Unfortunately, the effect was that the trailer brakes stayed permanently on.
I believe it was the brake signal and the 12V wires that were switched. Unfortunately, I don't remember for sure, but etrailer support knew exactly the issue and told me which two they were.
There are two ways to fix this. The ugly way is to cut and splice the wires to their correct place. That's the way most people recommend, but there is actually an even easier way with no cutting: remove the orange insert from the end the plugs into your car's wiring (I believe there were tabs on the side that I had to press to do so). Now, you will be able to remove the wires/contacts from the connector, so simply switch the two that need to be switched. Click the orange piece back into place. Voila, it's fixed, no cutting required.
Anyway, apart from that wire switching issue, it's a nice product.
by: Andy T.10/19/2018
2019 Dodge Ram Pickup
I just installed my Curt TriFlex Trailer Brake Controller C51140 in my new 2019 Ram 1500 Laramie 4x4 Crew Cab. Thanks to the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51458, it only took 4-5 minutes. Hardest part was finding the factory connector under the dash to plug into. etrailer has this wiring adapter listed as "Not confirmed to work" for the 2019 Ram 1500 but after my test drive I'm very satisfied. Worked just as I expected. I'll update this review after I have more time behind the wheel towing.
by: Paul 02/26/2024
Delivered early. Was just what I wanted.
by: Antonio05/08/2016
The product came very fast and it was super easy to install. It's working better than I thought, I'm very happy with www.etrailer.com and there products. Definitely worth every penny and everything top quality. Thanks!!!!
by: Jason 02/23/2024
Dodge Ram Pickup
Worked great on my Ram, fast shipping.
by: Greg05/07/2018
2018 Dodge Ram Pickup
I recently purchased a 2018 Dodge Ram 1500 and traded in my 2014 Dodge Ram. I had removed my Curt brake controller and was to install it in the new Ram. Unfortunately, the connections were not the same, and I needed an adaptor. I called etrailer and was extremely happy with the service. Tammy looked up my truck and controller and matched the adaptor. The process took less than 3 minutes. I received the adaptor in just days. Thank you Tammy for making this easy.
by: Gene 08/14/2023
Almost plug-n-go.The hardest part was where to put the controller !
by: Andrew08/02/2017
Very happy with controler and bracket. Easy to install took me only minutes.
by: Andrey12/22/2023
Very happy
by: Robert03/12/2018
Came in exactly as I expected, looked up under the dash and found the wire, should be a ten minute install. Sure makes it easy when etrailer has your vehicle specific cable for install. Will have to add more when I get to use it under tow with my RV trailer.
Robert
3/13/2019
The cable install fit perfect and my system works great, the install was less than five minutes. Thanks etrailer!
by: Tim01/28/2019
I needed this adapter to connect the brake controller to my specific vehicle. Etrailer had it available when I bought the controller from them , so I ordered it. Easy connection, works great.
by: John 07/26/2023
Thank you Paula, great help. Enjoy the rest of the summer.
25
136
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- Parts Needed To Install Curt Venturer Trailer Brake Controller 2023 Hyundai Santa Cruz Factory 4-Way
- You will be able to install the Curt Venturer NEXT Trailer Brake Controller # C74VV on your 2023 Hyundai Santa Cruz with the Pigtail # C77BR. As you only have a 4-way flat you will need the Curt T-Connector Vehicle Wiring Harness # C68JR to install a 7-way on the rear of your Santa Cruz. A Mounting Bracket # C67UR is needed to secure the 7-way since there is not a bumper cutout like you find on most trucks.
view full answer... - Install Harness for Curt Venturer Next in 2007 Ford F-250
- Yes you do need an install harness to install the Curt Venturer Next part # C74VV in your 2007 Ford F-250 with the part # C51372 being the correct harness.
view full answer... - Connection Point for Curt Venturer Brake Controller Wiring Under Dash of 2010 Ram 1500
- Thank you for the photo of your 2010 Ram 1500's under-dash wiring. The gray plug shown does appear to be the correct one for connection to the mating gray plug on the Curt wiring harness # C51438. This Curt connector is shown in the other photo so that you can compare the two. The black connector on the other end of the Curt harness will plug in to the wiring at the back of the Venturer brake controller # C74VV.
view full answer... - Installation of Curt Venturer Electronic Brake Controller in 1999 Chevrolet S-10
- To install the Curt Venturer Electric Brake Controller # C74VV you definitely need the red wire.
Black to 12 volt power
White to ground
Blue to 7-way at rear of vehicle
Red to cold side of the stop light switch
The cold side of the stop light switch will have power only when the brake pedal is pressed. The red wire carries the signal from the brake pedal to the controller so it can send a signal on the blue wire to the trailer's brakes.
The wiring harness to hardwire into your
view full answer... - Can Curt Venturer Brake Controller Install in 1998 Jeep Grand Cherokee
- Yes, the Curt Venturer part # C74VV can be used on your 1998 Jeep Grand Cherokee with a factory 7-way.
Next, for a wiring kit to install the brake controller to the 7-way you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none
view full answer... - Malfunction of Curt Venturer Brake Controller # C74VV Used with Electric-Over-Hydraulic Brakes
- The Curt Venturer Brake Controller # C74VV that you are using is designed for use only with electric trailer brakes. Since you mention a solenoid it sounds like your trailer may be equipped with an electric-over-hydraulic brake actuator. Such a system will not work with the Curt Venturer.
If this is the case you will need to choose another brake controller that has a switchable setting to allow it to be used with EOH brake actuators. Curt offers their Tri-Flex # C24VV that is compatible
view full answer... - Location For Brake Controller Adapter # C51436 To Plug Into On 2010 Ford F-150
- On your Ford 2010 F-150, the harness location should be located under the dash, above the brake pedal and taped to another harness. I have attached a photo that shows the typical location for the harness location on your truck. If you have the shifter in the center console of your F-150 it will be located under the center console. I have attached the installation instructions for the Curt Custom Wiring Adapter, part # C51436. The instructions show the typical installation locations for
view full answer... - Where Does Wiring Harness for Curt Venturer Connect to in Cab of 2016 Ford F-150
- The Curt Venturer Brake Controller # C74VV installs with the wiring harness # C51436 behind a panel in your 2016 Ford F-150's dash counsel. The panel you will need to remove in just to the right on the steering wheel. See the video I've attached and skip ahead to about the 2:30 mark to see the panel. From their the video will show you the rest of the install.
view full answer... - Mounting Curt Venturer NEXT Trailer Brake Controller
- Curt has started using new brackets for their brake controllers, and that is also true for the Curt Venturer NEXT Trailer Brake Controller # C74VV.
To mount this, all you have to do is put the included adhesive tape onto the included bracket and stick it wherever you like under your dash. If you'd like, you can also use the included screws with the adhesive to mount the bracket under your dash. With the bracket mounted, you'll just slide the Venturer NEXT controller into the bracket
view full answer... - Plug-In Wiring Adapter For 2012 Ram 1500 With Tow Package For Curt Trailer Brake Controller
- Thank you for your purchase of the Curt Venturer Trailer Brake Controller # C74VV. As for the plug-in wiring adapter for your 2012 Ram 1500 with the factory tow package, the correct part number is the following:
- Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51438
view full answer... - What Is Needed To Install Brake Controller On 2005 Ford F-150 With Factory Tow Package
- On your 2005 Ford F-150 with the towing package, there will be a port under the dash that the Curt Custom Wiring Adapter, part # C51322 plugs into. I have attached a photo that has a red arrow pointing to the location on your truck.
The Curt Venturer Trailer Brake Controller, part # C74VV is a time-delayed brake controller designed for a trailer with electric brakes or and Electric Over Hydraulic. It uses a preset sensitivity setting to activate your trailer brakes when you press the
view full answer... - Parts Needed To Install Brake Controller on 2005 Dodge Ram 1500
- Since your 2005 Dodge Ram has the factory installed 7-Way, to install a brake controller you will just need the brake controller itself and the proper wiring harness to plug it into your Ram.
If you go with the Curt Venturer, # C74VV, the only other part you will need is wiring harness # C51332. I have included a link to the installation details for you.
The wiring harness plugs into a connector already on your vehicle. The connector is located underneath the dash, to the left of
view full answer... - No Power To Curt Venturer Brake Controller On 2001 Jeep Grand Cherokee
- You stated that you have your controller all hooked up to your 2001 Jeep Grand Cherokee. It sounds like the power wire has possibly not been connected. When properly installed, the brake controller will still turn on. For you model Jeep, we offer a harness that connects to the back of the brake controller, part # C74VV.
The harness number is part # C51515. The plug connects to the back of the brake controller, and the 4 wires on the other end are hardwired to your vehicle. The black
view full answer... - Normal Indication Lights For Curt Venturer Brake Controller
- I called Curt to make sure that this is normal when the trailer is not connected. They confirmed that your brake controller is working exactly like it should. There should be a red light when you get in, and then it should change to a green light.
view full answer... - Why Isn't Curt Brake Controller Work on 2006 GMC Sierra 1500 After Install
- Under the hood of your 2006 GMC Sierra 1500 there are some connections that need to be made to activate the brake controller wiring. If you check out the help article I attached you can see what you need to do.
view full answer... - Could Curt Triflex Replace Curt Venturer In 2015 Jeep Wrangler Unlimited
- Yes a proportional Curt controller like the part # C24VV could easily replace a # C74VV. It would be just a matter of unplugging the old controller and plugging in the new one.
For suspension enhancement I would go with the Timbren kit part # TJRJK instead of an air bag kit because maintaining air pressure in bags can be a bit of a hassle and the Timbrens get installed and you never have to think about them again.
view full answer... - Where Does a Curt Venturer Brake Controller Plug In on a 2016 Ram 1500
- In order to install the Curt Venturer brake controller # C74VV on your 2016 Ram 1500 you will need wiring harness # C51458. It plugs into the factory plug on the truck located under the dash, to the right of the steering column, taped to another harness.
I included a picture showing the location. the picture is from the instructions for # C51458 which I have also linked for you.
view full answer... - Troubleshooting Constant 12V Power on Blue Brake Output Wire with Curt Venturer Brake Controller
- If you are reading a constant 12 volts on the blue brake output wire with the Curt Venturer Brake Controller # C74VV installed, this is indeed an indication that either the controller itself is bad or there's a short somewhere along the brake output wire on your truck (between the controller and 7-Way connector).
The first thing I recommend doing is severing the blue wire just a few inches behind the Curt Venturer and testing for power again on this wire. This will isolate the controller
view full answer... - Troubleshooting A Trailer That Is Not Connecting To Two Separate Newer Ram Trucks
- Trucks such as your newer Ram trucks send a small amount of power through the connector on the truck and them detecting a load is what tells the truck that the trailer is connected.
Since neither of your trucks is detecting that specific trailer the issue is more than likely that there is corrosion or debris in the trailer connector so you will want to check it very thoroughly. If you find any white/green corrosion then it is likely that there is corrosion inside of the connector as
view full answer... - Brake Controller Recommendation for 2020 Ram 2500
- We can get your 2020 Ram 2500 set up with a brake controller, and I recommend an option from Curt; you will also need the correct wiring adapter:
- Curt Assure Trailer Brake Controller with Dynamic Screen # C49UR
- Wiring Adapter # C51458
I highly recommend the Assure because it will give your trailer smooth braking proportional to that of your Ram so you have a more comfortable, safe towing experience. Along with that, the Assure stands out because of its large OLED screen that
view full answer... - Tekonsha Brake Controller Adapter for 2020 Ram 1500 With Factory 7-Way
- The Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51458 is absolutely compatible with your 2020 Ram 1500 with the factory 7-way.
view full answer... - Does Curt Assure Trailer Brake Controller Plug Into 2019 Ram 2500
- The Curt Assure is 100 percent compatible and will work with your 2019 Ram 2500. You only need the Plug-In Wiring Adapter and you're set.
This is a great choice for a brake controller because it is simple to use, has a really nice, easy-to-read display and will give you consistently smooth braking. There are no other items you need except the brake controller and harness; the exact part numbers you need are the following:
- Curt Assure Trailer Brake Controller # C49UR
- Curt Custom
view full answer... - Does Curt Assure Trailer Brake Controller Work With 2019 Ram 1500 Classic
- So long as your 2019 Ram 1500 Classic does NOT have the factory brake controller, then yes, you can use the Curt brake controller, and you will also need the correct wiring harness, which I've listed below for you:
- Curt Assure Trailer Brake Controller with Dynamic Screen # C49UR
- Curt Custom Wiring Adapter for Trailer Brake Controllers # C51458
The Assure is a superb option for a brake controller because it not only gives your trailer smooth braking proportional to that of your
view full answer... - Which Curt Brake Controller Harness Fits a 2015 Ram
- Part of the problem is the harness you are using is the incorrect one. You would need the part # C51458 for your 2015 Ram 1500 and not the # C51453.
The correct harness for your does not have the extra wire that you are mentioning since your truck does not require it.
view full answer... - Does Curt Brake Controller Harness Fit New Body Style 2020 Ram 1500
- Yes I can; the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51458 is a fit for the new body style 2020 Ram 1500.
view full answer... - Does 2019 Ram 1500 Need to be Flashed Using Curt Discovery Brake Controller
- Thank you for your purchase from etrailer of the Curt Discovery Brake Controller # C84VV and Wiring Adapter # C51458, we appreciate it. Your 2019 Ram 1500's computer does not need to be flashed/programmed when using this controller it will be plug and play. The exception is if you are replacing the factory brake controller, as you would then need to do so.
view full answer... - Wiring Harness to Install Tekonsha Brake Controller on 2022 Ram 1500
- To install a Tekonsha brake controller on your 2022 Ram 1500 you will just need the Wiring Adapter # C51458. The gray plug will connect to your vehicle under the dash and then you'll cut off the black connector and splice it (per color) to your current Tekonsha pigtail.
If you plan on still using the brake controller with your old truck when you need to then you might consider picking up another mounting bracket for your Ram. For example, the Prodigy P3 # 90195 would use the mounting bracket
view full answer... - Plug-In Curt Brake Controller Adapter for 2024 Ram 1500 & What Controllers Does it Fit
- For your 2024 Ram 1500, the correct Curt brake controller wiring harness is the Curt Custom Wiring Adapter for Trailer Brake Controllers # C51458.
This will give you a simple plug-and-play brake controller wiring harness (keep in mind this will not work if you have the OEM brake controller), and here are the brake controllers that this adapter works with:
- Curt Spectrum Trailer Brake Controller # C51170
- Curt TriFlex NEXT Trailer Brake Controller # C24VV
- Curt Discovery NEXT
view full answer... - Curt Brake Controller Install Harness for 2017 Ram 2500
- For your 2017 Ram 2500 the correct Curt brake controller install harness is the # C51458 which will work great with most of the Curt controllers but not the Discovery as this controller does not like the lower voltage that your truck puts out for the brake signal. You would have to go with a new controller like the Venturer part # C74VV.
view full answer... - Does Curt Discovery Brake Controller in 2018 Ram 1500 Require Going to Dealer
- Nope, you do not have to go to the dealer at all in order to install the Curt brake controller in your 2018 Ram 1500. All you need is the brake controller and the plug-in adapter, which are the following for your truck:
- Curt Discovery Trailer Brake Controller # C84VV
- Curt Custom Wiring Adapter for Trailer Brake Controllers # C51458
view full answer... - Brake Controller Install Harness Recommendation for 2018 Jeep Wrangler
- Yes, I confirmed with Curt that the trailer wiring install harness part # C51458 that you referenced is a confirmed fit for your 2018 Jeep Wrangler and will make installing a brake controller easy. It will plug right into the port under the dash of your vehicle to make installing the brake controller easy.
view full answer... - Can Curt Discovery NEXT Brake Controller Install in 2018 Ram 1500
- So long as you do NOT have the factory brake controller your 2018 Ram 1500 can install the Curt Discovery NEXT Trailer Brake Controller # C84VV with the Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51458.
view full answer... - Is There An Adapter Available For Red Arc Tow-Pro Brake Controller For 2019 Jeep Wrangler
- Yes, you can use the Curt Adapter part # C51458 for the 2019 Jeep Wrangler Rubicon with the Redarc Tow-Pro Elite part # RED44FR. You would just need to cut off the end of the adapter that goes into the brake controller and hard wire it to the Red Arc controller. The other end would plug into the factory tow port.
view full answer...
Info for these parts were:
Edited by:
Lindsey S
Expert Research:
Jameson C
Installed by:
Cole B
Written by:
Chelsea B
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Kenneth
3/20/2024
Still doing a great job. Well satisfied with product.