Where Does a Curt Venturer Brake Controller Plug In on a 2016 Ram 1500

Question

Question:

is there a video anywhere od the install of the curt venturer ebrake setup anywhere?Or would you know where the wires are under the dash?

asked by: Matthew D

0

Expert Reply:

In order to install the Curt Venturer brake controller # C74VV on your 2016 Ram 1500 you will need wiring harness # C51458. It plugs into the factory plug on the truck located under the dash, to the right of the steering column, taped to another harness.

I included a picture showing the location. the picture is from the instructions for # C51458 which I have also linked for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

The brake controller port for your 2019 Ram 3500 is a bit of an odd location relative to where the port is on other trucks; the port is underneath the control knobs like in the accompanying photo. You will be able to find the plug behind that panel,…

view full answer...

Answer 2

I have a solution for you, but the 7.00x 15 LT tire size you have is a light truck tire size. LT tires should not be used on trailers although some do without issue. Trailer tires are designed with a thicker sidewall that can accommodate higher air…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 10

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...