Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
Part Numbers: C84VV,C51382
Retail:$166.00
Our Price: $132.77
You Save: $33.23
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed
part number: C84VV
An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity.
Features:
- Brake controller activates trailer brakes with preset intensity
- Adjustable power output control lets you select the amount of braking force
- Rocker switches located on left front of module for easy access
- 10 Gain settings and 9 load settings allow you to adapt to various driving conditions
- Select a higher setting for harder braking and lower for more gradual braking
- Pinch-trigger manual override is within easy reach for controlling trailer sway or stopping in emergencies
- Simple LED display shows the amount of power output
- Self-diagnostics monitor trailer connection and check for shorts
- LCD display shows power adjustments in 0.5 increments
- Brightness is adjustable for optimal visibility
- Auto-sleep mode prevents battery drain after 5 minutes of idle time
- Quick and easy installation with no mounting restrictions
- No need to mount level - install anywhere at any angle
- Included mounting bracket and hardware designed to hold the brake controller flush against the dash
- Plug-in, vehicle-specific brake control adapter (sold separately) available for select vehicles to reduce installation time
Specs:
- Application: trailers with up to 4 axles (8 brake assemblies)
- Compatible with low-volt, PWM, ABS, cruise control, and electric-over-hydraulic trailer brakes
- Dimensions: 4" long x 3-1/8" wide x 1" tall
- Limited lifetime warranty
Gain Adjustment
Gain control lets you set the maximum amount of power that will be applied to your trailer's brakes, adjusting in increments of 0.5. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to go as high as you can without the trailer brakes locking up. Typically, the gain is only readjusted when you experience changing road conditions or if the weight of your trailer changes. To get more power to your brakes, press the upper orange rocker switch. To decrease the gain, press the lower switch. When you make your adjustment, the gain setting will show on the LED screen for 10 seconds as a series of bars and then go into sleep mode.
Load Control
Once you have the gain set, you can fine-tune your braking by adjusting the load control on a scale of 1 to 9. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. Load control can get the braking power to your trailer faster and with more intensity so that it doesn't push your tow vehicle forward. If your vehicle takes too long to come to a stop, increase the setting by pressing the upper black rocker switch. If it stops too abruptly, decrease the setting by pressing the lower switch. You can alter the setting to suit your driving preferences or to improve handling based on changing road conditions or varied trailer loads.
Pinch-Trigger Manual Override
The Discovery comes with a easy-to-reach, pinch-trigger manual override, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just push in the trigger. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
LED Display
The LED display on the Discovery is large and easy to read at a glance. It will show you what setting the brake controller is on as well as give you information for troubleshooting. You can adjust the screen brightness or trigger night mode so it won't glare obnoxiously on your dash. Press the control button to cycle through the different modes.
Quick Installation
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, so long as you can still easily access the controller and the manual override. The included bracket is designed to mount the brake controller flush to the dash so it takes up almost no space at all.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Time-Delayed Braking
The Curt Discovery comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the Discovery. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. Both the amount of braking power (gain) and rate of application (load) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
51126 Curt Discovery NEXT Time Delay Trailer Brake Control - 1 to 4 Axles
Replaces Curt 51120
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
part number: C51382
Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your controller and then plug the other end into the built-in port beneath your vehicle's dash.
Features:
- Plug-in wiring adapter allows for quick, simple installation of your electric trailer brake controller
- No cutting or splicing required on most applications
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible with time-delayed and proportional brake controllers from Curt
- Brake controller must have built-in plug for adapter to connect - will not work on controllers with pigtail wiring harnesses
- 2' Long, 12-gauge wires have protective covering to deter damage
- Limited 1-year warranty
Note: The factory brake controller plug on certain Nissan Titan XE models has a pin configuration that does not match up with this adapter plug. To install this adapter in those vehicles, hardwiring is required.
Installation of Curt Brake Controller Adapter
To install your Curt electric brake controller, you need to connect the wiring of the controller to your vehicle. Certain auto manufacturers offer pre-wired options, typically known as tow packages, wherein wiring is run for you from the dash to the trailer connector on the back of your vehicle. When this is done, a port is installed at your dash so that you can easily plug in a brake controller.
This adapter plugs into the port on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, and it is taped to another harness near the emergency brake pedal.
No hardwiring is required to install this adapter in most vehicles. After you plug it into the factory port, you simply plug the other end of the adapter directly into your electric trailer brake controller. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time to transfer it to another vehicle or securely stow it away.
51382 Curt Quick Plug Brake Control Adaptor Harness
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Defective
- Product did not meet expectations
- Alternate product found
Customer Reviews
Curt Discovery NEXT Trailer Brake Controller - 1 to 4 Axles - Time Delayed - C84VV
Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In - C51382
Average Customer Rating: 4.8 out of 5 stars (205 Customer Reviews)
An easy-to-read digital number display, 10 power levels, and a pinch-trigger manual override make this time-delayed brake controller easy to use. Installation is simple with no mounting restrictions. Activates brakes with a preset intensity. Install your Curt electric trailer brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your controller and then plug the other end into the built-in port beneath your vehicle's dash.by: KENNY09/06/2016
2016 Nissan Frontier
I installed the Curt C51110 controller with the Plug & Play C51382 into my 2016 Frontier, works perfectly.
by: David04/17/2024
Nissan Armada
The Curt Echo is now on my Nissan Armada and works perfectly. It was an easy hookup with the supplied harness and does its job.
by: Timothy04/22/2021
I've had the brake controller in use for over a year in my 2012 Nissan Frontier. The install was easy and took about an hour. My truck is a 2WD model so I mounted the controller in the plug that is used to select between 2WD and 4WD on vehicles equipped with 4WD. So the install look like factory.
by: bbells02/20/2024
Simple connection. FYI: On the 22-24 Nissan Frontier the plug-in is left of your left knee, above the kick panel. It is the larger of the 2 white connectors. No need to take kick panel off.
by: Philip 02/09/2024
Nissan Frontier
This custom wiring adapter made hooking up my Curt controller very easy to my factory wired nissan frontier.
by: John R05/24/2024
Took about 10 minutes to install. Have not made all the adjustments yet, but is easy to understand.
by: John R05/24/2024
2017 Nissan Frontier
Plugs right in without effort. Stiff enough that it loops behind dash and is well hidden
by: Jerry 04/25/2024
Nissan Pathfinder
exactly product, fits perfect in my Nissan Pathfinder platinum 2014
by: Peter 04/25/2024
it worked as it was designed to
by: Jerry 04/25/2024
Tested . Work fine and advertised
by: Forrest11/30/2021
2019 Nissan Frontier
For the most part I have been very happy with the merchandise that I have ordered from etrailer. But right now, I think that the people pulling the orders have to slow down a little and look closer at the details. I had ordered a C51382 cable but was sent a C51362 cable. They are not inter-changeable. They are shipping a new cable today (Tue.) I am supposed to get it by Thursday, depending on what time it gets here I may be able to get it done Thursday night and then calibrate the brake controller. Otherwise I am supposed to be on the road Friday but first I will have to take care of this and calibrating the brake controller on top of everything else.
Jenny N.
12/1/2021
I will have our customer service team reach out to you.
by: Brian C06/07/2016
2010 Nissan Armada
So much easier than cutting wires and crimping butt splices. Plus it make un-installation easier and doesn't void the warranty for the brake controller. the time saved was worth the money for me.
Bri
6/7/2017
One year later and unlike my guitar hero drum kit the insulation on the wires has not cracked and fallen off yet. Plus its nice to be able to unplug the unit from the car.
by: Ethan 03/15/2024
excellent service and delivery.
by: Russell11/03/2017
2004 Nissan Titan
I ordered this wiring harness because it said it would work with my 2004 Nissan
Titan. It does not. The plug on one end of the harness matches none of the plugs on the truck wiring.
Laura E.
11/8/2017
Thanks for pointing this out, Russell. The factory brake controller plug on some vehicles primarily XE models do not have the 4 pins to match up with the adapter plug. The factory plug will need to be hardwired onto the brake controller adapter that was purchased.
by: Debbie08/10/2022
Your company is awesome! I can’t write about the brake controller because my mechanic is putting it on today and it is the one he recommended. What I can write about is the customer service. You made ordering simple and the follow-up is fantastic. Delivery was quick and there were no delays. I will use your company again — and again. Thank you…
by: Sidney 09/21/2023
Like its compact size and simple operat ion.
by: Michael01/22/2023
Nissan
Worked great. Exactly what I needed to hook up my brake controller on my 2018 Nissan Armada
by: Dusten09/21/2023
Very helpful, knowledgeable and friendl y!
by: Anthony03/25/2020
Nissan Frontier
The trailer light kit I got was very easy to install with the helpful video and instruction etrailer has. etrailer made it very easy to select the correct trailer accessories for my Frontier. They were helpful when I called and the website is very easy to use! I have made other purchases through etrailer because it is easy to use and they have what I needed all in one place. Thanks!
by: Ralph M.09/11/2013
Great product!!! Installed in a matter of minutes. Determining where to attach the control took longer than the install. Pulled the trailer on a trip on roads with several steep inclines and applied the trailer brakes sparingly on the decent. Was able to adjust with the proper brake applications needed. Worked great. Made me feel confident that I could control the trailer on any road way. I very much recommend this trailer brake control for two axle trailers.
by: Mark 04/22/2023
Item arrived 3 days early and was exactly what I needed. Customer support was excellent. I highly recommend and would gladly use etrailer again.
by: Ricky F.03/09/2017
Ordered gooseneck hitch, wiring harness and break controller for my truck. Perfect fit , easy connections best purchase ever made on internet. Very good price and great customer service! ??
by: David04/02/2019
This product is easy to install with the correct harnesses. It is relatively basic, but it handled our application quite nicely. I was a complete novice when I started this project and had to learn as I went, but this is a nice brake controller.
by: George09/22/2020
Truly plug and go, except at the back of the truck when the trailer plug harness plugged in, the brake wire and power wire were crossed. Research explained that Nissan Frontier's are known for the unconventional switch with aftermarket wiring. I simply cut, switched, soldered. All good now.
by: Robert J.06/21/2015
etrailers out did my expectations. I ordered a trailer brake controller and pigtail one day, and they were at my doorstep the very next day. Boy, talk about fast. My rig works great , easy as pie setup, good price ( and I did look around), no problems at all. You guys are great. I will be buying from etrailer.com again for any of my trailer and accessories. Great job guys and girls.
25
205
Show More Reviews Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
- How Does Brake Controller Install in 2012 Ford F-150
- When installing the Curt Discover part # C84VV with the harness for your 2012 Ford F-150, part # C51436 all you'd have to do is plug in the controller and harness and you'd be set if you have the factory 7-way like it sounds like you do. It's really a pretty simple install.
Otherwise you'd need a 4-way to 7-way adapter like part # 37185 and you'd have to run the wire from the truck's frame rail to the adapter and you'd be set. See attached picture for more info on that.
view full answer... - Brake Output on Connector with No Trailer Connected Using Curt Discovery Trailer Brake Controller
- In regards to the Curt Discovery Trailer Brake Controller part # C84VV, there should not be power on the brake output pin inside the trailer connector without a trailer hooked up. There could be a few different things causing this but in order to rule out the brake controller you'll want to do a bench test outlined below. If the controller test good then that means you have a short on the brake output wire on the vehicle and you'd need to start tracing and checking for shorts. It may also
view full answer... - Curt Discovery Brake Controller Shows OL Error When Trailer is Connected
- It is possible that it is a simple wiring issue that is causing the errors on your Curt Discovery brake controller # C84VV. On your 2010 Chevy Silverado, there is a tow package wire bundle under the dash to wire in a brake controller.
The tow package red goes to brake controller black. White goes to white, blue to blue, and the light blue or orange wire on the truck goes to the brake controller red wire.
The OL indicates an overload and if all of the connections at the brake controller
view full answer... - Parts Needed to Install Curt Discovery Brake Controller in 2014 Chevy Tahoe
- To install the Curt Discovery brake controller # C84VV in your 2014 Chevy Tahoe you'll need the install harness part # C51515. This wires to the blunt cut wires that are under the dash of your Tahoe.
To see how it installs check out the install video that shows this controller installed in a similar 2015 Chevy Tahoe.
view full answer... - Replacement Brake Controller that is More Reliable Than Curt Discovery
- You have successfully diagnosed your Curt Discover brake controller part # C84VV as having an internal issue. It really is a bummer if this is the second one you recieved with an internal issue but I can't say I am too shocked since we've seen the Curt brake controllers be pretty problematic. The Draw Tite Activator part # TK90160 is a similar controller that is MUCH more reliable.
view full answer... - Brake Controller Installation on 2011 Toyota Tundra
- If your 2011 Tundra has the factory tow package, which includes the factory installed 7-way trailer connector on the rear bumper, it will be equipped with the tow package plug under the dash, as shown in the photo I've edited for you. Some models with the factory 4-pole (or 4-pin) trailer connector will also have the plug under the dash, you'll need to look for a white plug located above and to the left of the emergency brake pedal, above the toe kick. Occasionally, the plug will be located
view full answer... - Troubleshooting Aggressive Trailer Braking with Curt Discovery on a 2018 Chevy Silverado 1500
- Have you tried going different speeds when you are adjusting the power output of the Curt Discovery Trailer Brake Controller # C84VV on your 2018 Chevy Silverado 1500?
If you are only testing it at a slow speed and the brakes on your trailer are already set to be aggressive then it wouldn't take very much for your trailer to brake. Try putting the power output at the lowest setting for the Discovery, test it, and then go to the highest setting and see if that makes a difference.
Let
view full answer... - Troubleshooting "Short" Error Code On Curt Discovery NEXT Trailer Brake Controller C84VV
- Hello Surg. It is definitely odd that you are seeing the "short" error code on the Curt Discovery NEXT Trailer Brake Controller # C84VV, especially since your Tacoma was pre-wired from the factory. Nonetheless, this error code is definitely not normal, and is an indication that something is wrong. The display should show the current gain setting when the manual override is applied.
With no trailer connected, the "short" code means that the red wire is connected to ground side of the stoplight
view full answer... - Curt Discovery Brake Controller Displays Decimal Point When Not Connected To Trailer
- The Curt Discovery Trailer Brake Controller - 1 to 4 Axles - Time Delayed, # C84VV, is working properly. It is designed to display the decimal when no trailer is connected and number when connected. The numbers should increase as you activate your manual override when connected to the trailer as well. I have attached the installation details for you and a video to help.
view full answer... - Help! Curt Discovery Trailer Brake Controller # C84VV Only Shows Decimal When Brake is Applied
- Since the Curt Discovery Trailer Brake Controller, # C84VV, is still displaying the decimal when the trailer is connected, the controller is not sensing a connection with the trailer brakes. In this case the issue is most likely related to a wiring problem or brake magnet problem. I would start by making sure that there isn't any corrosion in either connector. Next, I recommend using a circuit tester like part # PTW2993, to make sure that you have power on the brake controller output pin
view full answer... - Harness Needed To Install Curt Trailer Brake Controller On 2021 Nissan Frontier w/ Tow Package
- In order to install the Curt Discovery part # C84VV on a 2021 Nissan Frontier with factory tow package you'll simply need the Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51382.
view full answer... - Troubleshooting Brake Controller that Only Works with Manual Override Lever
- This is a fairly common problem and the solution is the red wire of the brake controller.
Make sure it is connected to a circuit that only sees voltage when the brakes are applied and none when released. Most likely the connection is the issue and just reconnecting the circuit will cause the controller to work again.
You can also check to make sure that the third brake light fuse is in good condition under the hood of the vehicle as well.
view full answer... - Adding a 7-Way Trailer Connector and Brake Controller to a 2004 Nissan Xterra
- I will be happy to clear up what all you will need to add the equipment to tow the trailer and activate the electric brakes.
First, if your 2004 Nissan Xterra does not already have a trailer hitch you will need to add one. A popular option is Curt trailer hitch # 13183. This is a Class III hitch with a 2 inch receiver. The hitch itself is rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight but limited to the vehicle capacity if lower.
I also recommend etrailer
view full answer... - OL Message on Curt Discovery Trailer Brake Controller
- There could be a few different things happening with your Curt Discovery Trailer Brake Controller part # C84VV. The first thing that could be happening is that you have a short on the red stop light switch wire. In order to rule this out you will need to probe the red wire going into the back of the brake controller. There should only be power on this wire with the brake pedal depressed. If there is when it is not then you know there is either a short in this wire or the stop light switch
view full answer... - How to Find and Access the Brake Light Switch Wire on a 2015 Toyota Highlander for Brake Controller
- If you check out the video I attached you will see how we installed a brake controller in a very similar 2014 Toyota Highlander as your 2015 model. We had to remove the lower dash panel (13:00 mark of the video), to make accessing the green wire possible.
The kit used for the install in the video is the part # ETBC7.
view full answer... - Installing a Brake Controller in a 2009 Chevy Suburban
- The 2009 Chevy Suburban does not have a port to plug in a brake controller which is the same as the trucks of the same year. But it does have the tow package wire bundle up under the dash, to the left of the steering column, held together with a white tag.
Pull the wire bundle out to wire in a brake controller. With Curt brake controller # C84VV you will also need pigtail # C51515. Then you can make the following connections:
Vehicle red/black wire to controller black wire for 12
view full answer... - Troubleshooting a Curt Discovery Brake Controller That Has Jerky Brakes
- Wes, it could be possible that your brakes are jerky after they are warm because you adjusted them while they were cold. So what you can do recommended to warm the brakes by applying the manual lever for a bit while driving at slow speed; once they're warmed you can adjust them properly.
Another possibility is that the delay is set too long on the controller. I'd suggest trying to set the delay to activate sooner and see if that fixes it. If all that does not work, then there could
view full answer... - Wiring Adapter for Installing Curt Discovery Brake Controller on 2014 Ford Explorer
- To install the Curt Discovery # C84VV brake controller on your 2014 Explorer, you'll need the Curt wiring adapter, part # C51322.
view full answer... - Can I Use the Curt Discovery Brake Controller in a 2021 Honda Pilot
- Yes. You could use the Curt Discovery # C84VV on your 2021 Honda Pilot with the plug and play adapter # C51392 to allow for an easier installation that won't require cutting into any wiring. However, the Discovery is a time delayed brake controller, which means that it applied the brakes with the same intensity and with a slight delay in response to the tow vehicle's brakes being pressed. I do typically recommend going with a proportional brake controller, which uses gyroscopes and sensors
view full answer... - Parts Needed to Install the Curt Discovery Brake Controller # C51120 on a 2013 Dodge Durango
- The Curt Discovery Trailer Brake Controller, # C84VV, and the Custom Wiring Adapter, # C51446, will work on your 2013 Dodge Durango without splicing as long as your Durango came with a factory 7-way trailer connector at the trailer hitch. The 7-way trailer connector would indicate that your truck has the factory tow package, which would include a brake controller plug under the drivers side dash. You should see a gray connector just to the left of the steering column.
If your Durango
view full answer... - Brake Controller Recommendation For 2013 Nissan Titan With Factory 7-Way
- There is a brake controller I really like for you 2013 Nissan Titan, and the good news is that since you have the factory 7-way, you don't have to do any installation as your truck is already wired. All you will need is the brake controller and the wiring harness and you're set. With that said, the controller I highly recommend for you is the following:
- Curt Assure Trailer Brake Controller with Dynamic Screen # C49UR
- Curt Custom Wiring Adapter for Trailer Brake Controllers # C51382
The
view full answer... - Redarc Brake Controller for 2014 Pathfinder
- Yes, the diagram is correct. Please also note the attached "official version" from installation instructions. Only the black wire needs to be pulled from the TPH-014 and run to the battery with the breaker fit inline. The remaining wires within the TPH-014 can be left in place and the Tow-Pro harness plugged into the vehicle trailer brake connector. I verified this with the Redarc too just to ensure.
view full answer... - Troubleshooting 2018 Nissan Frontier SV with Brakes that Lock Up when Key is Turned On
- The brake controller and the brake controller wiring you mentioned does not affect the 12 volt accessory circuit of the 7-way that you are wanting to use to charge your trailer battery. Now with that said if your trailer brakes are locking up as soon as the ignition comes on that to me indicates that you have the brake output and the 12 volt accessory circuits either wired backwards (most likely) or there's a short between the two circuits.
The 12 volt accessory circuit should be in
view full answer... - Recommended Curt Brake Controller Wiring for 2017 Nissan Titan
- If you have a factory 7 way in your 2017 Nissan Titan, then the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In # C51382 is all you need for your brake controller.
If you don't have the factory 7-way, then you will use that same harness and then also the Factory Style 7-Way and 4-Way Flat Vehicle End Trailer Connector # N40975.
view full answer... - Availability of Curt Brake Controller Plug-In Harness for 2018 Nissan Armada
- I spoke with my contact at Curt regarding a brake controller plug-in harness for your 2018 Nissan Armada.
If you had previously used the Custom Wiring Adapter # C51382 for the controller in your Pathfinder, this same harness should carry over to your 2018 model Armada without issue. They have not been able to physically test/confirm the fitment simply because they have not yet had access to the 2018 model vehicle, but there have been no generational changes between the model years so
view full answer... - Installation of Redarcs Tow-Pro Liberty Brake Controller on Nissan Pathfinder with CAN Bus System
- Yes, per the installation instructions, your 2014 Nissan Pathfinder with the Controller Area Network, or CAN Bus system, it is recommended by the manufacturer that you use the 30-amp circuit breaker kit # 331-CBK30-EB. This, along with your Redarc Tow-Pro Liberty Brake Controller, # RED24FR and the Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers, # RED39FR (TPH-014) will have you all set. As long as your Pathfinder has the factory 7-way already. However, to add
view full answer... - Which Curt Brake Controller Install Harness for 2017 Nissan Titan
- The correct Curt brake controller install harness for your 2017 Nissan Titan S is the part # C51382 which explains why the # C51383 is not working for your truck.
view full answer... - Parts Needed to Install Curt Venturer Brake Controller in 2004 Toyota Tundra with 7-Way
- To install the Curt Venturer part # C74VV in your 2004 Toyota Tundra will require the install harness part # C51362.
view full answer... - Curt Brake Controller Install Harness Recommendation for 1999 Ford F-250
- For installing a Curt brake controller like the Triflex part # C24VV in your 1999 Ford F-250 the correct install harness is the part # C51322 which is a confirmed custom fit and would work well.
view full answer... - Where to Connect the Adapter to Install a Curt Brake Controller in a 2017 Nissan Pathfinder
- To install a Curt Brake Controller, like the Discovery # C84VV, on your 2017 Nissan Pathfinder you will simply need to plug the Custom Wiring Adapter # C51382 under your dash like you mentioned.
I am attaching a video where one of our install guys installed a Tekonsha Prodigy P2 # 90885 in a 2013 Pathfinder using the Tekonsha Wiring Adapter # 3050-P. If you skip to the 2:45 mark you can see where he plugs in the adapter for the Prodigy P2. Your Curt adapter will plug into the same place.
view full answer...
Info for these parts were:
Edited by:
Leah B
Written by:
Lindsey S
Expert Research:
Jameson C
Installed by:
Cole B
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Kenny
9/6/2017
ITS BEEN A YEAR SINCE INSTALLATION, ITS BEEN IN THE SAME LOCATION, HAVENT HAD ANY PROBLEMS! GREAT PRODUCT, GREAT PRICE!