Filter Results
$161.95 - $161.95
$389.95 - $389.95
$161.95 - $339.95
Filter by Storage Location
$161.95 - $161.95
$389.95 - $389.95
$161.95 - $339.95
Videos
for Under Seat Storage
Help Articles
for Under Seat Storage
Expert Answers
for Under Seat Storage
Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower…
view full answer...The Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs item #TDHP are going to be the shortest option we carry. With the hooks on the turnbuckle portion out from the inside of one hook to the inside of the other hook is 12". The minimum…
view full answer...Yes, it is! I checked with BAK Industries and the BAK Revolver X4s Hard Tonneau Cover item #BAK62VR you were looking at is compatible with the BAKBox 2 Collapsible Truck Bed Toolbox item #BAK92120. I can confirm that both of these parts will fit the…
view full answer...Hey Perry, so due to the door style that is at the rear of a 2023 Mercedes Sprinter the Inno tilt cargo carrier part #IN94MR wouldn't allow the door to open as it would sit up too tall even folded down but I do have a similar solution that would…
view full answer...Yes, the BAKBox 2 Collapsible Truck Bed Toolbox for BAK Revolver X2, BAK Roll-X, and BAKFlip Tonneau Covers #BAK92120 will work with your Bak Revolver X4 tonneau cover.
view full answer...The Thule TracRac SR Sliding Truck Bed Ladder Rack #TH43002XT-781 comes with the needed expansion block pocket mounts so there is no need to order them separately if you are getting this ladder rack for your 2015 GMC Sierra 2500 with a 6-1/2 foot…
view full answer...Using the Gen-Y Hitch Shock Absorbing 5th Wheel-Gooseneck Pin Box #325-GH-8045 will result in clearance issues because of the Rambox. You also do not want to use a sliding hitch for the same reason. In order to make this work, you will need a fixed…
view full answer...In regards to the Curt Trailer Hitch Receiver part #C15302 which is a fit for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, there are only two factory weld nuts in the frame which get reused, they are the two closest to the bumper. The other…
view full answer...I attached a picture that shows what the three different styles of wiper blades look like. Beam and Frame are the most different and Hybrid is mix of the two. The #MCH8519 is the hybrid style in the middle.
view full answer...The B&W Continuum Weight Distribution System part #BW28FR is great for varying loads since you can easily adjust the tongue weight setting. That said, I don't recommend this system when going off-road as it hangs down too low and could create…
view full answer...We do have a trailer hitch receiver that fits your 2024 Nissan Pathfinder, from Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C46DR
view full answer...Thanks for the picture! The longest weight distribution shank we have that fits a 2-1/2" hitch receiver is the Equal-i-zer Weight Distribution Shank item #EQ94FR. From hitch pin hole to the end of the shank is 12". It has a maximum tongue…
view full answer...Videos
for Under Seat Storage
Help Articles
for Under Seat Storage
Expert Answers
for Under Seat Storage
Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will…
view full answer...The Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs item #TDHP are going to be the shortest option we carry. With the hooks on the turnbuckle portion out from the inside of one hook to the inside of the other hook is 12". The…
view full answer...Yes, it is! I checked with BAK Industries and the BAK Revolver X4s Hard Tonneau Cover item #BAK62VR you were looking at is compatible with the BAKBox 2 Collapsible Truck Bed Toolbox item #BAK92120. I can confirm that both of these parts will fit…
view full answer...Hey Perry, so due to the door style that is at the rear of a 2023 Mercedes Sprinter the Inno tilt cargo carrier part #IN94MR wouldn't allow the door to open as it would sit up too tall even folded down but I do have a similar solution that…
view full answer...Yes, the BAKBox 2 Collapsible Truck Bed Toolbox for BAK Revolver X2, BAK Roll-X, and BAKFlip Tonneau Covers #BAK92120 will work with your Bak Revolver X4 tonneau cover.
view full answer...The Thule TracRac SR Sliding Truck Bed Ladder Rack #TH43002XT-781 comes with the needed expansion block pocket mounts so there is no need to order them separately if you are getting this ladder rack for your 2015 GMC Sierra 2500 with a 6-1/2 foot…
view full answer...Using the Gen-Y Hitch Shock Absorbing 5th Wheel-Gooseneck Pin Box #325-GH-8045 will result in clearance issues because of the Rambox. You also do not want to use a sliding hitch for the same reason. In order to make this work, you will need a fixed…
view full answer...In regards to the Curt Trailer Hitch Receiver part #C15302 which is a fit for a 2001 Chevrolet Silverado 2500 HD - 6-1/2 Foot Bed, there are only two factory weld nuts in the frame which get reused, they are the two closest to the bumper. The other…
view full answer...I attached a picture that shows what the three different styles of wiper blades look like. Beam and Frame are the most different and Hybrid is mix of the two. The #MCH8519 is the hybrid style in the middle.
view full answer...The B&W Continuum Weight Distribution System part #BW28FR is great for varying loads since you can easily adjust the tongue weight setting. That said, I don't recommend this system when going off-road as it hangs down too low and…
view full answer...We do have a trailer hitch receiver that fits your 2024 Nissan Pathfinder, from Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C46DR
view full answer...Thanks for the picture! The longest weight distribution shank we have that fits a 2-1/2" hitch receiver is the Equal-i-zer Weight Distribution Shank item #EQ94FR. From hitch pin hole to the end of the shank is 12". It has a maximum…
view full answer...