Will the BAKBox 2 Collapsible Truck Bed Toolbox Work W/ the BAK Revolver X4

Question

Question:

Will this box work with the BAK Revolver X4s cover?

asked by: Jared L

0

Expert Reply:

Yes, the BAKBox 2 Collapsible Truck Bed Toolbox for BAK Revolver X2, BAK Roll-X, and BAKFlip Tonneau Covers # BAK92120 will work with your Bak Revolver X4 tonneau cover.

expert reply by: Bryce D

0

Answer 1

When a BAK Revolver like the part #BAK39331 is rolled up it's diameter is 8 inches. So it would add 8 inches to the height of your truck bed at the very front of your truck bed where it would then be 8 inches wide. The width of your trailer nose…

view full answer...

Answer 2

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 10

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 11

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 12

Hey Bob, thanks for writing in, and you got yourself one heck of a truck with the 2024 Silverado 2500HD. And though you'll need an adapter since you have the factory prep package you can definitely use the Andersen Ultimate Connection 5th Wheel…

view full answer...

Will the BAKBox 2 Collapsible Truck Bed Toolbox Work W/ the BAK Revolver X4

Continue Researching