We don't carry the replacement hardware for the soft top of your 1987 Suzuki Samurai, but the Bestop Replace-A-Top # B5136101 comes with everything needed to replace the top of your vehicle and attach to factory hardware. view full answer...
It sounds like you have a bolt pattern of 4 on 4 inch, but the dimension you listed is slightly off from what this bolt pattern is. What you will want to do is measure from one hole center straight across to the hole center opposite of it. If this dimension is right at 4 inches then you do have a 4 on 4 inch bolt pattern and all of the rims at the attached link will fit. view full answer...
It sound like you want the opposite of adapter # 30104. That would mean your tow vehicle has a 6-Way square connector. What you can do is use # 37995 which has both the vehicle end and trailer ends.
On the trailer end, you can wire the loose wires to a vehicle side 4-Way, # HM48190. Then you will have a 6-Way square to 4-Way flat adapter.
The other option is to just replace the 4-Way flat on the trailer with the trailer end 6-Way that comes with # 37995. view full answer...
For the floor mats, we have a selection of semi-custom fit front mats like WeatherTech All-Weather Front Floor Mats in gray # WTW3GR or tan # WTW3TN. For the rear, it's a semi-custom fit from Weather Tech in gray # WTW20GR, tan # WTW20TN, or black # WTW20. I linked our full selection below.
As for snaps, we don't have exact replacement snaps for the replacement soft top for the Suzuki Samurai # B5136101. We do have extra snap fasteners though like the Snap Fasteners for Cloth # 37281575... view full answer...
For your 1987 Suzuki Samurai we have the Inno roof rack part numbers # INB117 and # INLD as a confirmed fit which would be an excellent choice! It's a square bar roof rack with a higher capacity at 220 lbs. view full answer...
When you lift a trailer you potentially change the suspension geometry which might affect handling characteristics. So based on that it sounds like Lance would want to void the warranty of the camper. It would be like installing a lift kit on a truck and then trying to have a suspension issue after that claimed as a warranty fix. That said, we've not had anyone install a lift on their trailer and then come back and tell us their trailer handled poorly. view full answer...
The only recommended way we have to connect a Roadmaster Stowmaster part # RM-501 to your 1987 Suzuki Samurai is to use a Roadmaster base plate kit like part # 1003-1. The bracket kit part # 40602 is not compatible with Roadmaster tow bars. view full answer...
Yes, you can flat tow your 2017 Jeep Wrangler JK, that has a AEV front bumper, using a Blue Ox # BX1133 Base Plate Kit, as long as your Jeep has the bolt on tabs as shown on page 4 of the Blue Ox installation instructions attached.
Most Jeep owners pair the Blue Ox base plate with the Blue Ox # BX7420 Tow Bar. This tow bar kit is heavy duty and will perform in most terrain and work with loads up to 10,000 pounds. It also comes with safety cables.
For lighting you can use the diode kit,... view full answer...
From the research I did it looks like you have a separate tail light circuit. Which means your turn signals and brake lights are carried on separate circuits. The easiest way to install diodes on your setup would be to use 4 diodes and have it so that the tail lights of your 1991 Suzuki Samarai will operate as a combined circuit, so basically your current brake lights will perform the turn signal and brake light functions.
Check out the picture I attached that shows how the 4 diodes of... view full answer...
Your Convert-a-Ball 5th Wheel to Gooseneck Adapter part # CAB-C5G can be locked with a padlock like our part # ML4140LH.
You'd pass the shackle of the lock through the locking handle slot and out the hole in the foot of the coupler. This prevents the coupler from being opened, so it can be used while the trailer is hitched or when it's not. Either way, the lock will help deter theft by making it difficult to unlock the coupler. view full answer...
No, the Roadmaster adapter # RM-033 itself isn't base plates. It is an adapter that attaches to Roadmaster base plates and allows you to then use certain Blue Ox and Demco tow bars. For actual base plates for the 1988 Suzuki Samurai we have Roadmaster base plates # 1003-1 and Blue Ox base plates # BX3501.
If you go with the Roadmaster base plates I recommend the Falcon 2 tow bar # RM-520. Or if you are looking for a more economical option I recommend the Tracker # RM-020. The Tracker costs... view full answer...
For your 1986 Suzuki Samurai, you can absolutely use your Tekonsha Prodigy P3 brake controller # 90195. You will need to start with the Curt Circuit Protected Converter w/ SMT # C56175 to get a 4-way trailer connection if you don't already have one. Then you will use the Universal Brake Controller Wiring Kit # ETBC7 to add the other features and install your brake controller.
You can use the Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers - 34" Long # 7894 to connect... view full answer...
You qukk need a car cover for your 1987 Suzuki Samurai but we do not carry car covers.
When your 2720 Trail Manor is closed the length is 20 foot 3 inches so for a cover the Adco Tyvek All Climate Cover part # 290-12252 would fit and work well. This works great basically in all climates and is the correct size for your pop up as well. view full answer...
The only ones we carry are universal style kits that require splicing with the exception of the ZCI # 119250KIT which is a fit for your 1987 Suzuki Samaria and is a universal kit but due to it's design does not require cutting of turn signal wires. view full answer...
The important thing is that the tow bar stays level, or more specifically stays within the "Safe Zone" which is 3 inches above or below level. As long as you are able to get the curved tow bar within this range with the height of the hitch ball on your RV the actual height is not a big deal.
To do this you will most likely need a high-low adapter like the Roadmaster # RM-048-8 on the RV. I have attached a great article that explains exactly how to choose the correct one for your setup.... view full answer...
The trailer tire size 5.70-8 is designed to fit a 3-3/4 inch wide wheel like the part # AM30153 which has a 4 on 4 inch bolt pattern or the part # AM30100 which has a 5 on 4-1/2 inch bolt pattern. view full answer...
Go To Results