Expert Answers about Suzuki SX4
- Recommended Trailer Hitch for Class I or Class II Ball Mount on 2008 Suzuki SX4
- Class I compatible ball mounts, such as the Draw-Tite # 3593, will typically have a shorter hitch pin hole measurement to the end of the shank. This allows it to be used on Class I trailer hitch receivers that have the stopper inside the receiver that can prevent higher-class accessories from fitting. There is not a standard measurement that will indicate whether you have a Class I or Class II ball mount, but if you are able to tell me the manufacturer/brand of your existing unit, I will...
view full answer... - Recommended Trailer Hitch for 2009 Suzuki SX4 Sedan
- The Curt Class I Round Tube Receiver Hitch # C11446 referenced in your question is indeed confirmed to fit your 2009 Suzuki SX4 Sedan. The is a custom hitch that is specifically designed for your vehicle, as it will use existing holes in its frame for a no-drill installation. It will provide you with a 1-1/4 inch receiver opening and it has a 200 pound tongue weight and 2,000 pound towing weight capacity.
I have attached the complete installation instructions that you can also check out....
view full answer... - Does the Yakima JayLow Kayak Carrier Come With Locks
- The Yakima JayLow Kayak Carrier part # Y04073 does not come with locks. They will need to be purchased separately using the Yakima Same Key System part # Y07202. The Yakima Same Key System will come with a random key code. There are several different key codes so although it is not impossible for someone to have the same key as you, the odds are very low.
view full answer... - Replacement Arms for Roadmaster Base Plate Kit and Adapter to Blue Ox Tow Bar
- You can order replacement arms for the Roadmaster base plate kits with the part # RM-ARMS. Then to convert to a Blue Ox tow bar you'd need the part # RM-032 and you'd be set.
view full answer... - Hitch Recommendation for a 2012 Suzuki SX4 Crossover Wagon
- I checked with Curt and the Curt Hitch part # C11446 that you referenced is confirmed to fit your 2012 Suzuke SX4 Crossover Wagon. The install will be pretty straightforward and not very difficult at all. Check out the installation instructions I attached to the right for more info.
For a ball mount you would want the Curt Class II Drawbar part # C45521, and then for a hitch ball you would want the 2 inch ball part # A-82 and then for a 1-7/8 inch ball you would want the # A-80.
view full answer... - Yakima Extended LoadWarrior Cargo Basket Recommendation
- The extension piece for the Yakima Loadwarriors are available separately, part # Y07074. But the rest of the basket is not.
Your best option would be to get the # Y07070-74 that is the extended Loadwarrior. The upside is you will still have your spare install brackets in case you were to lose any.
view full answer... - Trailer Hitch and Cargo Carrier Recommendation for 2013 Suzuki SX4
- For your 2013 Suzuki SX4 we have the Curt hitch part # C11446 which is a fit for the sedan models and the part # C11443 which is a fit for the hatchback models.
We have 2 carriers that you could use, the Curt # C18145 that weighs 28 pounds with rails or the Curt #C18110 with a mesh floor and no rails that weighs 30 pounds.
Curt requires the use of their stabilizer strap part # 18050 when using their hitch to carry a non-supported load like a cargo carrier. I attached a review video for...
view full answer... - Are Crossbars of Malone AirFlow2 Roof Rack # MPG215 Sold As Pair or Individually
- The Malone AirFlow2 Roof Rack # MPG215 that you referenced is sold as a pair.
view full answer... - 2007 Suzuki SX4 Crossover Hitch Cargo Carrier Recommendation with Curt Hitch
- For a Class I hitch like the part # C11443 which is what you'd have installed on your 2007 Suzuki SX4 you are putting quite a bit of leverage on it with a hitch adapter/riser. You most likely are straining the hitch beyond what it can safely handle too which is asking for trouble. The sag you mentioned is a good indicator of that.
Your best option is a cargo carrier that fits the hitch without the use of an adapter like the # C18145. You would also need a stabilizer strap # 18050, this...
view full answer... - Will Curt Hitch part # C11443 Work With Surco Hitch Cargo Carrier 52017
- The Draw Tite hitch part # 24817 that you referenced will work well with the Reese hitch cargo carrier part # 63155. This is very similar to the Surco Carrier that you referenced. The two notable differences is the size is 1 inch shorter at 20 X 47. and it weighs 4 pound more. The hitch is a Class I hitch and the carrier is Class I compatible so there would be no issues.
I attached a review video for the carrier being installed and used in a Class I hitch for you to check out as well.
view full answer... - Parts Needed to Flat Tow 2012 Suzuki SX4 with Ready Brute Elite Tow Bar
- The only adapter we have that will work with a Ready Brute Elite Tow Bar is the part # BX88297 which is designed for Blue Ox base plate kits. For a Blue Ox base plate kit that fits your 2012 Suzuki SX4 we have the part # BX3522 which is a confirmed fit.
view full answer... - 7-Way Extension for Use with 36 Inch SuperTruss Extension
- To extend the 7-Way trailer connector out from the back of your truck to the mount on the SuperTruss extension I recommend # TLW6036 which is 36 inches long. Then you could use the Flexo-Coil kit # RM-146-7 like normal.
view full answer...
Go To Results