Expert Answers about Toyota RAV4
- Parts Needed To Add Curt Echo Trailer Brake Controller To a 2022 Toyota RAV4 With Factory 4-Way
- As you already have the Curt Trailer Connector Adapter # C57672 to connect to the 4-way on your 2022 Toyota RAV4, the Curt Echo Wireless Trailer Brake Controller # C51180 only requires an additional charge line to be ran. For this you will need some 10 Gauge Wire # 10-1-1 to run to the battery. This wire is sold per foot so be sure to get enough for routing safely and away from rotating parts or exhaust to prevent damage to the wire. Cable Ties # DW05724-25 will work well to secure the...
view full answer... - All Parts Needed to Flat Tow a 2001 Toyota RAV4
- I can list all the parts you need in order to flat tow your 2001 Toyota RAV4, though you need to verify with your Toyota dealer that a 2001 RAV4 can be flat towed (I checked an online copy of the owner's manual, which did not specify).
There are a number of parts needed in order to flat tow your 2001 RAV4, which I'll list for you:
- Base Plate Kit: Demco Classic Base Plate Kit # DM9517115
- Tow Bar: Demco Excali-Bar III Non-Binding Tow Bar # DM9511013
- Wiring Kit: Roadmaster Diode 7-Wire...
view full answer... - Wiring Harness For A 2010 Toyota RAV4
- The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118412 is confirmed to fit your 2010 Toyota RAV4.
The trailer harness will give you the 4-flat connector and make it to where your trailer's stop, turn and taillights will mirror your vehicle's stop, turn and taillights.
The custom-fit T-One connector will plug into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area. Once you've...
view full answer... - Parts Needed To Add 7-Way Wiring Harness to 2017 Toyota RAV4
- We do have a 7-way you can add that will do exactly what you need on your 2017 Toyota RAV4. If you don't already have a 4-way you will need to add that first. You can use the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118578. Like you said, this is what you would normally use to power your trailer's signal lights.
Once this is installed you can add the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires # ETBC7L. This is designed for a...
view full answer... - Parts Needed to Switch a Thule WingBar Evo from a 2012 VW to a 2022 Toyota Rav4 w/ Flush Rails
- It looks like you will most likely need new feet as well as the fit kit. From what I can find, most 2012 VW's with a bare roof used the Evo Clamp Feet for Thule Crossbars # TH710501. The fit kit for the 2022 Toyota Rav4 with flush mounted rails uses the Evo Fixpoint Feet for Thule Evo Crossbars # TH49SC.
Fit kit and feet for Thule WingBar Evo on a 2022 Toyota Rav4 with Flush Mount Rails:
- Fit Kit for Thule Podium-Style Roof Rack Feet # TH78RE
- Evo Fixpoint Feet for Thule Evo Crossbars...
view full answer... - Parts Needed to Flat Tow a 1996 Toyota RAV4 Behind an RV
- In order to flat tow your 1996 Toyota RAV4, all wheel drive with manual transmission, I have found that you will need to have a transmission lube pump installed. For other towing requirements for your vehicle, be sure to consult the owners manual.
There are several other components that are needed to flat tow a vehicle starting with base plates. Base plates provide a safe and secure attachment point for a tow bar. You can use XL Base Plates, # 1142-1. For a tow bar, you will need one that...
view full answer... - Recommended Roof Rack For Thule TH898 Hullavator Kayak Carrier on 2019 Toyota RAV4
- In order for the Thule # TH898 Hullavator to be compatible with your RAV4, the crossbars would need to extend at least 4 inches beyond the foot that attaches the crossbar to the raised rails. Thule recommends the # TH710401 roof rack feet and the # TH711400 53 inch crossbars for your vehicle, but you'll need to take a measurement to see if those crossbars will be long enough. You'll need to measure the outside to outside distance of the raised rails on your roof. If this distance is 45...
view full answer... - Parts Needed To Attach Rhino Rack Aero Roof Rack On a 2023 Toyota RAV4 With Naked Roof
- First you will need the Rhino-Rack Vortex Aero Crossbars # RRVA126B-2. These will attach to the Legs # RRRLKVA which connect to your 2023 Toyota RAV4 using the Fit Kit # RR27QP.
view full answer... - Parts Needed to Install Autowbrake and 7-Way for Towing with a 2016 Toyota RAV4
- To use the Autowbrake with your 2016 Toyota RAV4 you need the following parts:
7-Way RV Upgrade Kit - # ETBC7L
Curt No-Drill Bracket - # C57202
Autowbrake Electric Brake Controller - # 3430001
Junction Box and Installation Kit - # 3430001-JBK
The 7-Way kit plugs into your 4-Way and then has a power lead that connects to the battery on your RAV4 which is needed for the Autowbrake, and the Curt bracket is needed to hold the 7-Way plug near your hitch receiver. Then the junction box gives...
view full answer... - Will the Saris Bones 2 Fit My 2018 Toyota RAV 4 and Will I Need Hatch Huggers?
- Yes, the Saris Bones 2 # SA805BL is confirmed to fit your 2018 Toyota RAV4. As far as the hatch huggers, you will need to order two sets of Hatch Huggers for Saris Trunk Mount Bike Racks # SA3035 to replace the side hooks and the lower hooks.
view full answer... - 2023 Toyota RAV4 Wiring Needed for Thule Epos Bike Rack w/ Lights
- The Thule Epos Bike Rack w/ Lights # TH49XE has a standard 4-Way flat connector (see attached) so you just need to install the Curt T-Connector # C56434 on your 2023 Toyota RAV4 for the lights to properly work.
I also recommend picking up the Mounting Brackets # C42CR and # C57202 so you can mount the 4-Way plug near the receiver on your Draw-Tite Hitch # DT82QR for easy access.
view full answer... - How to Add 7 Way Connector to 2021 Toyota RAV4 with TRD Off-Road Package
- In order to add a 7 way connector to your 2021 Toyota RAV4 TRD you'll need the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7 (for wired brake controllers) or the # ETBC7L (for a wireless brake controller). This will use your existing 4 way plug and you'll just need to make a connection to the ground, auxiliary wire for 12v power, and the reverse light circuit and the brake control output wire (not required when using the ETBC7L)....
view full answer... - Recommended Brake Controller and Trailer Wiring for 2009 Toyota RAV4
- There is no one kit that includes the 4-pole harness you need along with the other brake controller installation parts but you have done a fine job of identifying the components you need. I would usually recommend the Curt harness # C56165 over the Tow Ready - its the same price and same install - because of its higher current output capacity. But if you already have it then it should work fine as long as your trailer lights do not demand more current than it can provide. An install video...
view full answer... - Is There an Adapter Needed to Use the Thule Spare Me with Mountain Bikes
- The Thule Spare Me # TH963PRO doesn't require any adapter for mountain bikes.
The only adapter you need is a frame adapter bar like the Kuat Ubar # UB01. This is used to create the horizontal top cross tube on bikes that don't have one like a women's bike. It creates the contact point for a hanging rack and helps keep a bike level.
view full answer... - Parts Needed to Use a Brake Controller in a 2011 Toyota Rav4 with 4-way Connector Present
- You are already on the correct track. In order to install a 7-way on your 2011 Toyota Rav4 you have to have a 4-way installed first. Since you already have a 4-way you can use the Universal Installation Kit for Trailer Brake Controller # ETBC7 to adapt your 4-way into a 7-way. You would still want to run the second power wire to the battery. The wire for the 4-way is only 10-amp while the 7-way wire is 40-amp and they are serving different purposes. I also recommend picking up the Curt...
view full answer... - Replacement Key for Sears Sport Cav-15 Cargo Box
- We offer many replacement keys for your Sears Sport Cav-15 Cargo Box. In order to ensure you get the correct key for your box, you just need the key number that is engraved on the lock core.
For your key number 2818, you will use the Replacement Key # THKEYN2818. This includes one key.
view full answer... - Tow Dolly for Towing 2011 Toyota RAV 4 Behind Motorhome
- FWD models of the RAV4 can be successfully dolly towed.
Given the weight of your RAV4, the Demco # DM9713045 Kar Kaddy SS you'd looked at would be the best choice. The dolly features hydraulically actuated disc brakes for exceptional braking performance. The surge brake system eliminates the need for a brake controller makes the dolly easier to use.
I've linked to a product demonstration video for the Kar Kaddy SS tow dolly.
view full answer... - Replacement Housing For Hopkins Adapter 4-Pole to 7-Pole and 4-Pole socket
- I spoke with Hopkins and they confirmed the housing is not replaceable, the only option is to replace the entire adapter with the Adapter 4-Pole to 7-Pole and 4-Pole # 37185.
view full answer... - Parts Needed To Install a 7-Way On a 2024 Toyota RAV4
- If you already have a 4-Way # C56434 you simply need to add our 7-Way Kit # ETBC7 to your 2024 Toyota RAV4. This kit will connect to your 4-way and includes wiring for the charge line and installing a Brake Controller # RED52VR.
view full answer... - Available 1-1/4" Hitch for 2015 Toyota RAV4
- Yes. There is a Class II hitch with a 1-1/4" receiver available for the 2015 RAV4 with the Curt # C12108 and the wiring harness I recommend using is the Tekonsha # 118578; Tekonsha harnesses have extremely reliable converter boxes and will do a great job for you.
You'll also need a ball mount, hitch ball, hitch pin and clip. For the ball mount I recommend using the Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs # C45518, which needs a hitch ball with a 3/4" shank...
view full answer...
Go To Results