Expert Answers about Toyota Camry

• Roof Rack For 2006 Toyota Camry That Is Compatible With Rhino-Rack Kayak Carrier S512
• The Yakima roof rack that fits your 2006 Toyota Camry naked roof is as follows: -Round Crossbars # Y00409 -Towers # Y28TR -Round Bar Adapters # Y03536 -Fit Kits # Y06121 AND # Y06144 Then you can install the Rhino Rack Carrier # s512 or many other accessories.
  view full answer...


• Parts Needed to Tow a 2009 Toyota Camry With a Fleetwood Revolution
• If your 2009 Toyota Camry has an automatic transmission, then it will require a tow dolly like the Roadmaster Tow Dolly, # RM-2050-1, that you referenced on our website. One advantage to using this tow dolly is that it already comes with brakes and lights which will minimize the amount of additional items you will need. In order to operate the electric brakes on this tow dolly, you will need to have a 6-Way round trailer connector on the motor home, and an electric brake controller. I...
  view full answer...


• Solution To Go From A 1-1/2 Inch Hose Fitting To A 3 Inch Bayonet Fitting
• We have the LaSalle # 34466V153 which will slide on over your 1-1/2" pipe to give you 3" pipe. From here you can use # T1028 to give you the bayonet fitting you're needing. Use the solvent cement # 3447530889 to complete installation and prevent leaks.
  view full answer...


• What is Needed to Install a 4 Way Flat Wiring Harness on a 2014 Toyota Camry
• What you are needing is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118405. This will provide you with a 4-way flat trailer connector at the back of your 2014 Toyota Camry to power your trailer's signal lights. This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk or cargo space, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to...
  view full answer...


• Do Roof Racks on 2017 Toyota Camry Come with Locks
• There are locking kits available with roof racks for your 2017 Toyota Camry. The Rhino Rack 2500, # DK321 has built-in locks, but you'll need kits for the Yakima rack that fits your Camry. The Yakima roof rack consists of the Crossbars # Y00421, Fit Kit # Y06119 and Towers # Y28TR. You would only need to install the Yakima Same Key System # Y07204 on the Towers to lock it. I added a link to the instructions of this part, as well as a link to an installation video of this system. I have...
  view full answer...


• Driver's Side LED Tail Light That Matches Optronics Combination LED Trailer Tail Light
• The correct Combination LED Trailer Tail Light that goes with the Optronics # STL8RB is the part # STL9RB like what you were talking about. The reason why it has that extra function and the extra diodes is because there is a clear light/lens on the underside of that light which is used to illuminate a license plate. You can definitely upgrade your incandescent lights to LED. This is becoming more and more common simply because LEDs last longer and typically burn brighter so they are...
  view full answer...


• Curt Trailer Hitch Receiver # C12343 Replacement Hardware Needed for 2007 Toyota Camry
• We have exactly what you need! Replacement Hardware Kit for Trailer Hitches, # RHK, includes all of the mounting hardware needed. Just go to the # RHK product page, enter the hitch number (C12343) and manufacturer (Curt) and you'll be set.
  view full answer...


• Trailer Hitch Receiver For 2002 Toyota Camry
• We do have available hitch options for your 2002 Toyota Camry, part # C12339 works for your application. I also recommend picking up # F-4 to secure your hitch mounted accessories. If you are planning on pulling a trailer I recommend part # C55308 for your wiring. The Curt T-Connector harness is a plug and play system which makes it simple to install.
  view full answer...


• Can Roadmaster Base Plates be Used with a Blue Ox Avail Tow Bar on a 1985 Toyota Camry
• Yes, you can use the Blue Ox tow bar, # BX7420, with Roadmaster base plates but you will need to use and adapter, # RM-033. You will also need to add lighting to your 1985 Toyota Camry. An easy solution is a magnetic lighting kit like # RM-2120. Most states now require a supplemental braking system on the vehicle being flat towed. The easiest to set up and use is a proportional system like # RM-9400 that applies the vehicle brakes in proportion to how much the towing vehicle is braking....
  view full answer...


• Accesories Needed to put a Hitch Bike Rack on a 2008 Toyota Camry SE with Draw Tite # 36416 Hitch
• There might be some products you may be interested in purchasing, but once you have this Draw-Tite Hitch Receiver, part # 36416 installed onto your 2008 Toyota Camry you would not need anything else to put a bike on the 1-1/4 inch receiver of the # 36416. I included the installation instructions and a video of the install being done on a similar Toyota Camry below. You will not need lights because the lights from your Camry should still be visible, and the bike rack attaches to the hitch...
  view full answer...


• Hitch Adapter To Make My 1-1/4 Inch Hitch To A 2 Inch Hitch On My 2022 Toyota Camry
• There will be no hitch adapters from 1-1/4 inch to 2 inch hitch that will not reduce the tongue weight capacity of the hitch by 50%.This adapter will reduce your tongue weight of your trailer hitch because it alters the distance and the geometry of the hitch tube, but with with the quality of the item The Hitch Adapter 1-1/4 inch to 2 inch Trailer Hitch Receiver # HTAD will be your best option. I attached a review video link below.
  view full answer...


• Parts Needed to Mount a Transmission Cooler on a 1999 Toyota Camry
• Derale Series 7000 Tube-Fin Cooler Core # D13317 is just a core, not a kit, so it does not include mounting hardware, hose, or fittings. The kits can be found in the link provided and do include all of these items. Since you already have the core though you will not need another kit. The kits include the following parts: Hose clamps, # D13008 Hose, # D13003 Universal mount kit, # D13001 Insta-Dapt fitting, # D13004 These are the parts you will need.
  view full answer...


• Information Needed to Replace the Lock Cylinder on an Older Thule Atlantis 2100 Roof Box
• I'd love to get you setup with a brand new lock for your Thule Atlantis 2100, however to do that I am going to need to know what number is stamped on the lock cylinder itself. This number will correlate to a key which will allow you to lock and unlock your box again. If the lock is unlocked and you want to start over with a different lock and key, then you could use the change key # 853-1251 to remove the old lock core, and then use the Thule One-Key System Lock Cylinders # TH450200 to...
  view full answer...


• Trailer Wiring Harness For A 1996 Toyota Camry
• The Hopkins Active Tail Light Converter with Install Kit # 46255 is confirmed for your 1996 Toyota Camry but I recommend choosing The Upgraded Modulite Vehicle Wiring Harness Kit # C59496. This kit has a stronger grade of wiring and will last a lot longer then the Hopkins model. This kit will power your trailer's stop, turn, tail and running lights directly from the tow vehicle's battery. This harness also virtually eliminates the draw on the vehicle's taillight circuit.
  view full answer...


• Tow Dolly That Is Capable Of Towing A 3,000-lbs Toyota Camry
• We do have a couple of dollies that will work great for you. The Demco Kar Kaddy SS Tow Dolly with Disc Brakes # DM9713045 will fit most vehicle's with a tire tread width of 42"-76", and has a maximum carrying capacity of 4.800-lbs. Or You can use the Roadmaster Tow Dolly with Electric Brakes # RM-2050-1 which has adjustable sliding ramps that can adjust 34"-77" to accommodate most vehicles, and has a maximum carrying capacity of 4,250-lbs. I recommend the Roadmaster Tow Dolly with...
  view full answer...


• Parts Needed to Tow a Small Trailer With a 2015 Toyota Camry
• You can install a trailer hitch on your 2015 Toyota Camry without voiding your warranty per the Federal Magnuson-Moss Warranty Act. The Act states that if something breaks on your vehicle and you take it in for warranty repair, the dealer must honor your warranty unless whatever modifications you have added to your vehicle actually caused the problem in question. If you still choose to tow then I recommend using the Draw-Tite # 36540 trailer hitch, Tekonsha Wiring # 118405, and Ball Mount...
  view full answer...


• Parts Needed to Tow With 2018 Toyota Camry XSE
• You can add parts to your 2018 Toyota Camry XSE in order to tow and you will need to start with a trailer hitch and I recommend the Curt Trailer Hitch #C11576 due to the company's reputation for high-quality trailer hitches. This is a Class I hitch with a 1-1/4" receiver that has a 2,000 lb towing capacity and 200 lb tongue weight capacity. Adding a wiring harness will also be necessary in order to power the lights on your trailer and the T-One Vehicle Wiring Harness with 4-Pole Flat...
  view full answer...


• Trailer Hitch Receiver for a Bike Rack on a 2018 Toyota Camry Hyrbrid
• The Curt hitch # C11576 is a confirmed fit for your 2018 Toyota Camry. It is also a confirmed to fit your hybrid model. All of the hardware is included so you won't need anything extra and it's a Class I hitch, so your Swagman rack will fit. You will also need a stabilization strap, part # 18050, per the hitch warranty.
  view full answer...


• Blue Fog Light Bulb to Fit 2005 Toyota Camry
• From my research your 2005 Toyota Camry uses a 9006 bulb for its fog lights. So the CIPA EVO Formance Spectras, # CM93423F is the correct blue bulb we carry that fits.
  view full answer...


• What Ball Mount Will Work With My Draw-Tite Class II hitch
• With The Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4 inch # 36540 you would need The Curt Class II Drawbar - 2-5/8 inch Rise, 3-1/4 inch Drop - 7-1/4 inch Long - 3,500 pounds # C45521. This ball mount has a 3/4 inch ball hold diameter which means you need either The 2 inch Hitch Ball - 3/4 inch Diameter x 2-1/8 inch Long Shank - Stainless Steel - 3,500 pounds # A-82 or The 1-7/8 inch Hitch Ball - 3/4 inch Diameter x 2-1/8 inch Long Shank - Stainless Steel - 2,000 pounds...
  view full answer...