The Gen-Y Adjustable 2-Ball Mount part # 325-GH-325 can be used for both towing and hitch mounted accessories at the same time. That said, the ball mount would likely need to be in one of the bottom two holes with the hitch mounted accessory in the top. In regards to weight, it has a very high 1,500 lb rating so as long as the tongue weight of the trailer and weight of the hitch mounted accessory are below this you will be fine. It's built like a tank so you should not have any concerns... view full answer...
Since you have a 2017 Armada the pre-wiring is on the right side of the steering column, above the accelerator (see pic). This is where you'll plug the part # 3050-P into for the Prodigy P3 part # 90195. view full answer...
If your vehicle has a 100 lb roof weight capacity the weight of the Yakima LockNLoad Platform Rack for Crossbars # Y05044-39 would count against that. So you'd have a total of 57 lbs of cargo weight you could carry. view full answer...
The Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 was designed to fit into a cutout like what the picture I attached shows. The wires on the back would prevent it from being able to mount flush.
Wall cutout size: 3-9/16" long x 3-7/16" wide x 1" deep view full answer...
You should be able to install the Tekonsha Voyager brake controller part # 39510 in your 2017 Nissan Armada with the install harness part # 3050-P and the 7-way install kit part # N40975 as our understanding is that every Armada in 2017 came wired for this setup.
Other option is to hardwire the brake controller with first wiring in a 4-way like part # C59236 and then using the kit part # ETBC7 to adapt this 4-way to a 7-way and allow you to hardwire in the controller. Check out the install... view full answer...
Yes, a weight distribution system will help keep your vehicle from sagging when hooked up. The spring bars of the weight distribution system work to transfer the load from the tongue of the trailer to the vehicle and trailer axles.
You will need to properly load your trailer so that the tongue weight is not too high and is within the limits of your towing system. This will also help keep your vehicle level. Generally your tongue weight should be within 10 to 15 percent of your gross trailer... view full answer...
I can help you determine what wire on your harness is for which function, but unfortunately we don't know what color wire holds what function on your 2017 Nissan Armada. What you will need to do is use a circuit tester like part # PTW2991 and test your wiring harness.
You will be able to find 2 of the functions easily. One will have constant power and one will only have power when you press your brake pedal. This leaves you with the ground wire and the wire that sends power to your trailer... view full answer...
The Curt Front Mount Trailer Hitch Receiver # C31081 will not have to be removed when changing the oil on your 2019 Nissan Armada. When the hitch is in place you will still be able to remove (and re-install) the factory skid plate, which is what needs to be taken off when changing the oil on this vehicle.
I have attached a full installation video below that you can use for reference, along with the written install manual. view full answer...
Yes you still need to ground the white wire for the Wiring Kit # ETBC7 because there are some additional functions that come with the 7-Way plug. You can actually use the same ground point that you used for your Vehicle Wiring Harness Kit # C59496 if it is nearby, otherwise you'll need to find another suitable location for this second ground. view full answer...
So long as you wire the side view cameras to the running light circuit, they will stay on continuously when using the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras # FCE48TASL-05.
When wired this way, the side cameras of the Vision S # FCE48TASL-05 won't just come on when the turn signals come on, and the monitor even has a tri-view display option so you can see both on the sides and behind you. view full answer...
The blue relay from the Curt Relay Kit for Nissan # C57000 is a replacement running light/turn signal relay for Nissan trucks and SUVs for trailer lights and tow package. One of the blue relays installs in a box under the driver-side dashboard to the left of the steering column.
This kit includes a brown relay to activate the 12-volt power circuit and two blue relays to activate turn signals. The linked video shows installation in a 2008 Armada. view full answer...
To install the Curt trailer brake controller wiring harness # C51382 you will need to locate the factory harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. I have linked a video and some instructions on another harness that fits that should help.
The Curt trailer brake controller wiring harness is compatible with Curt brand brake controllers that accept the plug, like the Echo Under-Dash # C27JR.... view full answer...
The Equalizer Weight Distribution system part # EQ37100ET that came with your camper is one of the nicest systems on the market. It can be adjusted to level your SUV and would be a much better solution than suspension enhancement.
The goal with an Equalizer weight distribution system is to get the distance from the ground to the wheel well half way back to the unloaded height when compared to the height of the vehicle with trailer connected.
So if the distance was 30 inches unloaded and... view full answer...
Yes, the factory style 4 and 7-Way connector # N40975 would be a perfect pairing with the Prodigy P2 brake controller # 90885.
You would simply plug the # N40975 connector into the factory socket you found near the driver side frame rail. The included relays would need to be installed in your relay panel, which would be located on the passenger side, near the battery.
The Prodigy P2 brake controller # 90885 and wiring adapter kit # 3050P would be used to complete the installation.... view full answer...
If your 2008 Nissan Armada did not come with a factory trailer connector then you can add one by first installing a 4-Way flat connector, # C59496, and then installing Brake Controller 7- and 4-Way Installation Kit # ETBC7. There isn't a kit that plugs in for models that did not come with the factory 7-Way so that is why this hardwire method is needed. I have included some links that show and explain the ETBC7 installation for you.
If your trailer has electric brakes that you want to use... view full answer...
Where the 3 inch tubing meets the air spring in kit # F4150 there is a collar that holds in the tubing. Push that collar towards the air spring and you will be able to pull out the tubing with your other hand. The little collar holds the tube in by compression. Pushing it in towards the spring releases the tension. view full answer...
Below the product images for the Firestone Coil-Rite Air Helper Springs # F4150 which fits your 2023 Nissan Armada you will find a link "Locate installers near me". This will allow you to search for installers along your route to determine which one will be able to help you during the timeframe you need.
I recommend also installing the Air Lift WirelessAIR Compressor System # AL58WQ when you install the air springs. This compressor includes a smart manifold which will allow you to make... view full answer...
On the Black Bracket with 2-Wire Plug for MC65 Series Clearance Lights # A68PB, I've attached a video to assist in showing you ground and power. If you have the light facing you with the wires to the left, the top wire will be power and the bottom will be your ground. view full answer...
You're very close, to see how your Tekonsha Voyager part # 39510 should install to the factory wiring of your 2012 Nissan Armada check out the chart I attached that shows how it all connects.
The red/blue wire you found will not be used, that is the third brake light circuit and is not needed. The B+ wire SHOULD be a red wire and will be the 12 volt circuit and would get run to the black wire of your controller. view full answer...
The green light on the Tekonsha Voyager Trailer Brake Controller # 39510 will only come on when a trailer with properly functioning brakes is connected. The light will turn red when either the brake pedal is pushed or the manual operation lever is used.
I have included a link to the instructions below that includes troubleshooting in case you have an issue when you do connect to the trailer. view full answer...
Go To Results