The overall size of the Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 is 33-9/16" long x 3-7/16" wide x 1" deep, and includes a white adapter plate for a flush mount installation. view full answer...
The Kodiak Trailer Wheel Lug Nut # KALN1375S that you referenced is a solid, stainless steel lug nut. The jacketed ones tend to swell over time from corrosion which makes it hard to fit wrenches on them but the solid ones will not swell. view full answer...
The Draw-Tite # 75699 has 1-3/4" from the center of the hitch pin hole to the edge of the receiver. I've linked an installation video of this hitch for you to check out as well. view full answer...
I apologize for any confusion but the Furrion 2-in-1 Range Oven with Glass Cover - 21inch Tall - Black Item # FR37KR that you referenced is definitely 21 inches tall. For some reason it's in a dimension category that show it as 16 inches tall but it definitely is 21. view full answer...
Most bike racks do have a 35-lb weight limit for each loaded bike and while it might seem fine to load one 50-lb bike instead of two 35-lbs bikes this is not something most rack makers recommend because the cradles, straps and other parts that hold the bike safely may not be rated for supporting one bike that is that heavy.
Nowadays there are many racks made for heavier bikes like electric bikes, beach cruisers and fat bikes which tend to be on the heavier side. All racks for heavy bikes... view full answer...
Your 2017 Chevy Equinox AWD is flat towable with a max speed of 65 mph as stated in the owners manual of your vehicle. Now if you hit 66 miles per hour for a few seconds when towing is the car going to immediately be damaged? Probably not, but to be on the safe side since transmission repairs aren't cheap I'd recommend sticking with 65 as the max.
For flat towing your Equinox, I recommend the Blue Ox Base Plate Kit - Removable Arms # BX1689 along with the Blue Ox Tow Bar - Motorhome Mount... view full answer...
On the Bulldog Winch Truck Winch Roller Fairlead # BDW20002 the mounting hole spacing, measured hole center to hole center, is 10-inches horizontally and 3/4-inch vertically. I took these measurements myself in our warehouse.
Usually only the upper two holes are used for installation in most applications, according to my contact at Superwinch. view full answer...
Yes, it will. The T-One Vehicle Wiring Harness item # 118727 you were looking at will work with or without the Auto Stop/Start feature on. It gets it's signal directly from the tail lights which stay on when your vehicle is stopped at a light. This wiring harness is custom fit for the 2017 Jeep Grand Cherokee's that do not have the tow package.
I have linked an installation video below to help you get it set up.
If you are planning on towing you will also need a hitch item # 75699 and... view full answer...
The Aries Bull Bar with Removable Skid Plate item # AAB35-1003 comes with some of the hardware needed to complete the installation but it does use the bolts that hold your tow hooks in place. I recommend sourcing the replacement hardware at your local Autozone or Oreilly.
The Aries Bull Bar with Removable Skid Plate item # AAB35-1003 is confirmed to fit your 2018 Jeep Grand Cherokee Laredo. view full answer...
Someone else has recently asked that question and a coworker made a lovely picture showing the measurement you are looking for on coupler # BD43805W0317. I have included that picture for you here. The inner width is 10-1/4 inches and the outer is 10-3/4 inches. view full answer...
On your 2015 Jeep Grand Cherokee Limited, The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75699 will have a 4-3/4 inch measurement from the center of the hitch pin hole to the outer most part of the bumper. The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13065 will measure 4 inches from the center of the hitch pin hole to the outer most part of the bumper.
The Kuat Transfer V2 Bike Platform Rack # KU74FR has a measurement of 7-1/2 inches... view full answer...
The Rhino-Rack Fairing for Roof Racks - 38" Long # RRRF2 will extend about 4-1/2 inches in front of your crossbar. The overall dimensions are 38 x 5 inches. I've attached a video to assist with the installation. view full answer...
The Draw-Tite Trailer Hitch item # DT42GR does not require any wiring to install on your 2023 Jeep Grand Cherokee. It is custom fit and bolts to your Jeep with included hardware. This is a class III hitch with a 2" receiver that has a 7,500 lbs towing capacity and a 1,125 lbs maximum tongue weight. You will want to verify your Jeep's actual capacity and go off of it though.
It looks like the 2023's come with a wiring harness and factory 7-way if you have the towing package. Some other... view full answer...
When towing, you're always going to be limited by your lowest rated component. No matter what you do, you're only going to be able to tow what your vehicle's capacity will allow. The components you mentioned would be good additions for your towing setup, but are meant to help stabilize your tow load and lower the stress on the vehicle components under towing conditions. They won't actually help you tow more weight; they will only make your towing experience much safer and the ride more... view full answer...
The 600 lb tongue weight round bar Fastway e2 Weight Distribution Hitch # FA94-00-0600 will hang down about 2-1/2 inches underneath the head system, and for an SUV like your 2015 Jeep Grand Cherokee there is likely not going to be any clearance issues, though there is no guarantee of course.
The best option - both for clearance and ease of install - really is the 600 lb tongue weight trunnion bar Fastway e2 Weight Distribution Hitch # FA92-00-0600.
This does not extend down past the... view full answer...
I did some digging around and could not find the exact weight. I can tell you that the shipping weight is 29 pounds and I would think the packaging would be around 3 pounds. So, the best estimate would be 26 pounds. view full answer...
There's quite a bit of adjustment in the brackets that install the Aries Step Bars # AA2061032 to your 2019 Jeep Grand Cherokee. If you check out the attached picture you can see the holes in the brackets are slotted where the steps attach to them. If you wanted them to sit closer to your vehicle you'd just need to loosen them and push them where you want and tighten them. It's hard to say why yours were installed the way they were but you can certainly make adjustments if you wanted them... view full answer...
Jeep rates the towing capacity of the 2015 Grand Cherokee with Pentastar V6 and Trailer Tow Group Package as 6200-lbs. The GC with the V8 hemi carries a 7200-lb rating as do the versions equipped with the EcoDiesel V6. So long as your vehicle is rated for at least 6200-lbs you should be fine to tow the Vette and trailer with a combined weight of 5500-lbs.
A vehicle's towing capacity is set by the auto maker and takes into account drivetrain components like the engine, transmission and... view full answer...
According to my technical contact at Timbren, the Axle-Less Trailer Suspension System # ASR1200S01 has a deflection of 2-1/8 inches.
He also told me if you are running right at 1200 lbs you would be better off installing the 2000 lb system. I have attached a link to take you to all of the 2000 lb systems we offer. The deflection of a 2000 lb system is 1-5/8 inches. view full answer...
I went out to our warehouse to take a look at the Curt 2" Hitch Ball # C40004 that you referenced and I measured a height of 2-3/4" from the mounting base to the top of the ball. I have attached an image to assist.
If this doesn't provide the height you need we also have the 2" ball available with an additional 1" rise with part # C40033 or an additional 2" rise with # C40034. These rise measurements would be added to the 2-3/4" height mentioned above. view full answer...
Go To Results