Thanks for reaching out, Josh!
The only carrier I can see working with the Curt Trailer Hitch Receiver # C12092 on your 2017 Ford C-Max is the 19x47 Curt Cargo Carrier # C18110 which is rated for 300 lbs. Since this is only 19" deep you'll have about 5" of the lawn aerator hanging over each side of the carrier but it's the best option for your situation.
Any other cargo carrier we have will use a higher wall profile so the aerator will have to sit a bit awkwardly on/in the carrier and... view full answer...
Well Curtis, we do have the Draw-Tite Max-Frame Trailer Hitch Receiver # DT84YR which I do see you already found for your 2017 Honda HR-V. This has the 2" opening and is rated up to 300lbs of tongue weight like you are looking for so it does meet your requirements.
I do recommend adding the 4-Way # 118673 when you install the receiver as you may need to add some Lights # 20174 to the Cargo Carrier # 63153. view full answer...
Hey John, thanks for reaching out!
We have a variety of ways to get your cargo (and spare!) traveling down the road with you, and part of it just depends on what exactly you're looking to get out if it, along with how much you're willing/wanting to spend.
My initial reaction to your question is to recommend installing the etrailer Trailer Hitch Receiver # e98853 on your 2017 Toyota Sienna and then using the Yakima EXO Swing Away Storage System w/ Enclosed Cargo Carrier and Cargo Carrier... view full answer...
Hello Don. So, there are technically no speed limitations when using the 22x60 Flint Hill Goods Cargo Carrier # FHG49ZR. Obviously, you will want to obey all posted speed limits and any other DOT regulations. The carrier is made to withstand bumps and ruts in the road within reason. If your roads are anything like ours here in Missouri, you are likely to run into a few potholes that are simply unreasonable, and in those scenarios, simply do your best to slow down and use caution. Basically,... view full answer...
Hello Craig. I do have a solution for you, but the Flint Hill Goods Wheelchair Carrier # FHG99ZR is not recommended for use behind RVs, campers, or trailers. The ride on the back of a 5th wheel or RV is a lot more rough than on the back of a car or SUV and the carrier simply is not rated for this kind of use.
What I recommend using instead is the 32x48 Reese Steel Solo Cargo Carrier # PS10401-10402. This is made for a 2" hitch and is rated for 400 lbs, so more than enough for your 100... view full answer...
The Spare Tire Carrier # FHG57ZR I feel is the best option to use with the 24x84 etrailer Cargo Carrier # e96ZR. This carrier has multiple bolt hole options and the bars on the other side allow you to distribute the weight across multiple bars on the rack. view full answer...
I recommend going with the etrailer Trailer Hitch Receiver # e98844. I'd choose this hitch over the primarily because it's got a the highest GTW rating, as well as the highest tongue weight rating, which is going to be pretty useful when using the 19x60 Curt Cargo Carrier for 2" Hitches # C18100. view full answer...
I do not see that Inno makes a license plate mount for their 39x25 Cargo Carrier with Removable Cargo Box # IN94MR. When I tried to contact them for input they only took my information and never returned my phone call. The Thule License Plate Holder # TH35JV looks like the best option as you can attach it with straps rather than having to drill into the the frame or box. view full answer...
Hey Nathan; since it looks like the front of your Haulmaster cargo carrier is solid, I recommend going with a light kit that has strong 3M adhesive for mounting as opposed to brackets which would be difficult to securely connect to a solid surface. With that I would go with the following LED kit:
- Curt Auxiliary LED Indicator Lights # C53201
The # C53201 gives you brake lights, turn signals, and running lights so you get the full package. This is super easy to use as all you do is stick... view full answer...
I have one hitch for your 2013 Mazda MX-5 Miata however, none of our spare tire carriers are small enough to fit it. The Curt Trailer Hitch item # C11028 is a class I hitch with a 1-1/4" receiver. Due to the small size and weight of your car this is the largest capacity hitch available.
All of our spare tire carriers like the Curt item # c31006 you were looking at fit a 2" class III receiver. Additionally, the owner's manuals prohibit the use of adapters like item # HTAD that would allow... view full answer...
Hi Tony,
For your specific needs I recommend the Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes # LGA77FR. This rack is rated for use on all vehicles, trailers, motorhome, etc. and has a 75lb per bike capacity. It has an adjustable base so that you can place the bikes further out if you need more space for a cargo carrier or spare tire and comes with an anti-rattle hitch pin to prevent any movement of the rack in the trailer hitch.
I've attached a short video below where... view full answer...
With the size of your Champion Generator 200953(23.4" wide, 27.9" long and 21.7" tall I recommend using the 32x48 Reese Solo Cargo Carrier # PS1040100. This has a 47-3/4" long by 31-3/4" wide inner tray and can support up to 400lbs so you could carry additional items with your 90lb generator if needed. Do be sure to verify with Coachmen you do not exceed any capacities on your hitch or trailer with the additional items. We do have the Cover # CH97FR which will protect your generator when... view full answer...
The simplest and most economical option is going to be the Hollywood Racks SR1 2-Bike Carrier # HRSR1. This does mount on the spare tire but the arms which hold the bike can be slide to the side allowing you to better center the bikes behind your 2004 Honda CR-V. Do understand the maximum weight for each bike is 35lbs for this and is common among these types of racks.
For a stronger rack that will be easier to use with your rear door you would want to add our Receiver # e69AR. This would... view full answer...
I did a little digging around and it looks like the roof on your 2021 Suabru Ascent is around 63 inches, making the Yakima LockNLoad Platform Roof Tray # Y05045 with the TimberLine Towers for Yakima Crossbars # Y33TR, and the LockNLoad SL Adapter for Yakima SkyLine and TimberLine Towers # Y05042-2 near perfect.
This platform rack measures 60" long, 54" wide, and will be a perfect addition to your Subaru for all your camping and luggage needs.
This rack also has top channels so you can... view full answer...
Hey Susan, the etrailer Trailer Hitch Receiver # e98853 will work fine as a mounting point for a spare tire carrier like # c31006. The receiver tube on this hitch is open all of the way through and theoretically you could access the back end of it but you wouldn't ever need to.
Finally, for a wiring harness I recommend going with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56261 which just plugs into your OEM wiring, and gives you with a 4-pole connector. view full answer...
I have a solution for you but those kind of roof racks don't work with vans because of the sliding doors. This explains why you aren't able to find any on the site.
To add a roof rack to a 2016 Dodge Grand Caravan, I recommend the SeaSucker Monkey Bars Roof Rack - Round Bars - 48" Long item # 298-SX6000B or the 60" item # SEA99FR. The Monkey Bars come with the easiest installation and removal process out of any roof rack. They suction cup to the top of your roof.
Since the diameter... view full answer...
I just want to ensure I am understanding you correctly because you say trailer but I think you are referring to carrier like the Flint Hill Goods # FHG77ZR. If this is similar to what you are meaning then yes, you will be able to use it with the EcoHitch Hidden Trailer Hitch Receiver # 306-X7221 on your 2016 Nissan Leaf. I do recommend also installing the Wiring # C56227 when you install the receiver as you will most likely need to add some Auxiliary Lights # C53201 to the carrier. This... view full answer...
Hello Paul. This is a common problem with a lot of factory crossbars. Just last week we tried to mount a kayak carrier on some Ford factory bars and we had the same problem. The factory crossbars were way too thin and curved and it made things difficult. Unfortunately, there is no alternative mounting kit that can be used the Thule Canyon XT Roof Cargo Basket # TH859XT-8591XT.
The best solution that we can offer is to remove the factory bars, and install an aftermarket roof rack. I recommend... view full answer...
The 2017 Toyota Tundra CrewMax has a 5.5' bed correct? If so, a great option for a ladder rack is the TruXedo Elevate Truck Bed Rack System # TX96NV. This is made to be compatible with many tonneau covers, including your Bakflip MX4 and it will allow you to open and close the cover normally with the rack installed.
Another thing I like about the TruXedo Elevate ladder Rack is the adjustable height. It can be used at full height (cab height) or there is an 18" setting if you want to lower... view full answer...
Hey Jeremy, thanks for reaching out!
I have a potential creative solution for you, but we unfortunately don't have any fishing rod carriers that mount on an RV ladder.
With that being said, the SeaSucker Ski and Snowboard Carrier # SEA46ZR can be mounted vertically on the body of an RV as long as it isn't a "warp" that it vacuum cup mounts to. Then you'll just need to make sure you have the reel mounted at the top just to ensure that the rod and reel don't work their way down and out... view full answer...
Go To Results