Expert Answers about Jeep Trailer Spindles

• Replacement Bearing Kit for a 2015 Karavan Boat Trailer with 2,652 lb Capacity
• It sounds like you either have a 1" BT8 spindle or a tapered #84 spindle on your Karavan trailer so you'll need one of the following kits: - Bearing Kit for 1" BT8 Spindle # BK1-100 - Bearing Kit for #84 Spindle # BK2-100 I recommend looking at the bearings on your trailer and comparing that to what comes in these kits prior to purchasing just to make sure everything will match up.
  view full answer...


• Hub & Drum And Electric Brakes For 2,000 lb & 2,200 lb Timbren Axle-Less With Long Spindle & 4" Lift
• Hey Dan, So I'm not quite sure if you are just wanting new hub/drums and electric brakes for your current 2,000 lb Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift # ASR2KHDS03, or you want to replace it with the 2,200 lb version which is part # ASR1THDS03. Either way, I can tell you the exact hub and drum along with electric brakes that you need, as the same hubs and brakes fit both systems. What you will need for either the 2,000 lb or 2,200 lb Axle-Less with...
  view full answer...


• What Brakes and Hubs Are Going To Be Used With The Timbren Axle-Less Trailer Suspension # ASR35HDS05
• The Timbren Axle-Less Trailer Suspension # ASR35HDS05 uses a larger spindle so you are going to need hub and brake components for a 5,200lb axle. We have our Standard Brakes # AKEBRK-6 or the Self-Adjusting Brakes # AKEBRK-7-SA which require less maintenance since they will adjust themselves as they wear. You will need 2 of the Hub/Drum Assemblies # AKHD-655-6-EZ-K for the spindle. These will have the 6 on 5-1/2" bolt pattern and works with 14-1/2" to 16-1/2" diameter wheels.
  view full answer...


• Bearing, Seals, And Caps For A 2008 Bear Boat Trailer
• Hi William, It looks like we have everything except for the grease seal. Could you measure the spindle for the inner diameter and hub bore hole for the outer diameter one more time to confirm? The Hub Bearing Kit # BK2-100 has the correct bearings and tang washer but uses a 10-19 grease seal # 58846 (ID: 1.719" - OD: 2.565"). For the grease caps you can use part # RG04-040 for easy lube spindles or # RG04-020 for standard spindles.
  view full answer...


• Parts Needed To Install 5 On 5-1/2" Bolt Pattern Hubs On a 1987 M105A2 Trailer
• To be able to run the same 5 on 5-1/2" bolt pattern for your Jeep Wrangler on the M105A2 trailer you are going to have to cut off your current spindles to have 2 Spindles # TRU77FR installed. This is the common size spindle found on a 3,500lb axle which will then let you install 2 of the Hub/Drums # AKHD-555-35-EZ-K. With these you will want to install Electric Brakes # 23-468-469 since they are much better on an Overlanding trailer than surge type brakes. We do have a Junction Box # 3430001-JBK...
  view full answer...


• Replacement 7K Dexter Axle with 95 Hub Face, 80 Spring Center and 9/16 Studs
• Hey Edward, thanks for reaching out! What you're looking for is the Dexter Trailer Axle Beam with E-Z Lube Spindles # 8327834. This is just the axle tube and spindles so to add brakes and the hub/drums to it you also need the following: - Nev-R-Adjust Trailer Brakes # 23-464-465 (1 kit per axle) - Hub/Drum Kit # 8-219-13UC3 (2 per axle)
  view full answer...


• How To Find Correct Idler Hub For 2004 EZ loader Boat Trailer With 2,999LB Axle Capacity
• There are 2 ways to figure out exactly what you need Chris as I cannot look up parts for your 2004 EZ Loader boat trailer based on just a model. If you have the VIN you or I can contact EZ Loader to verify the correct bearings and seals used on your current hubs or you can pull a hub off and get the part numbers off the parts. If the part numbers are not visible you could also measure the spindle using a Caliper # PTW80157. Based on the axle weight you most likely have the #84 spindle...
  view full answer...


• Info Needed to Pick Out Replacement Bearings/Seal for 2004 Glastron Boat Trailer
• Hey Jim, we have a way to help you pick out the bearings and seals you'd need but we don't have a way to know what you need with just the info you listed. Basically we need to determine what your axle capacity is and then from there we can find what you'll need. On the axle there should be a sticker or label that has the capacity listed but otherwise you can determine it by getting the diameter of the axle. Worse case scenario you can just pull the trailer hub off the spindle and from...
  view full answer...


• How to Identify Replacement Bearings for 2003 Jayco Kiwi 23B
• Based on the weight of your trailer it likely has a 3,500 lb axle. However, you will need to identify the axle first to be sure. You can either check the axle tag or pull off the hubs to check the bearings. If the bearings don't have part numbers in the side you can measure the inside diameter or the spindle where the bearing rides with a digital caliper like # PTW80157. Assuming I'm right about the axle you have a # L44649 outer and # L68149 inner bearing. The correct bearing kit would...
  view full answer...


• What Parts Are Needed to Replace Hub/Drums and Brake Assemblies 4,400 lb Trailer Axle
• Hey Rob, sorry to hear about the problems you had with your current hub/drums. The good news is you did order everything you would need and no additional parts would be necessary. The two pieces you pointed out with your yellow arrows do need to come off as they are parts of the old bearings that were destroyed.
  view full answer...


• Replacement Bearing Kit Needed for a 2006 Marine Master Model TR196-2S
• Hey Roger, thanks for the information! I reached out to Marine Master because I wasn't able to find any information, and this is what they replied to me with: "This trailer came with original oil bath hubs with the DB-42 brake system. The MMT03059 or the MMT-TB kit might work for it but I would need to know if the spindle has a hole in the front and if the wear sleeve has a hole also for the grease to go through." If you can get back with me on whether your spindle and wear sleeve has...
  view full answer...


• Oil Bath Conversion Kit for Ranger Trail Boat Trailer
• Your Ranger Trail boat trailer is not something we have information on so you will need to identify your axle/hubs to find the right parts. Once you have identified the axle you may be able to use one of the following: -Kodiak XL ProLube Kit for 3500-lb Axles # XLPROLUBE1980KIT -Kodiak XL ProLube Kit for for 5,200-lb to 6,000-lb Axles # XLPROLUBE2440KIT These kits are designed for standard axles. The 3,500 lb kit fits a 1.98" hub bore and the seals fit a 1.72" spindle. The 5,200-6,000...
  view full answer...


• How Does DeeMax 6k Disc Brake Kit Attach to Trailer Axle
• Hey Aaron, the DeeMax Disc Brake kit part # DE28YR that you referenced is designed to attach to a brake mounting flange that is on the trailer spindle. If your trailer was missing that the correct flange for a 6k axle would be the part # 4-44-1.
  view full answer...


• Are There Electric Trailer Brakes To Replace Warner Brakes On a 1960's Trailer?
• Unfortunately Bill, we are not going to have any parts that will let you keep your current axles. You can either look at getting replacement axles which I can help you find or you can look at installing the more common #42 Spindle # TRU37FR or # TRU39FR on your axle. These would need to be welded in by a shop with an axle jig to ensure they go on perfectly straight. If you can let me know what width axle you have from hub face to hub face and spring center to spring center I can determine...
  view full answer...


• How to Determine Trailer Bearings For 10 Inch Hub & Drum
• in order to find the correct bearings for your hub, you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If you are unable to find them, you need to use a digital caliper and measure your spindle where the bearings ride, like in the photo I added. It would also help to know your axle capacity (which should be stamped on the axle itself); and for a 10 inch...
  view full answer...


• Parts Needed To Add Electric Brakes To An Aluma 6812H Tilt Aluminum Trailer
• Hi Eric, The first step to adding brakes to a trailer is to check if your axle has a brake flange to mount the brake assemblies to. If your axle doesn't have a brake flange then you'll have to replace the axle with one that does. Assuming yours does the next step is to mount brake assemblies # AKEBRK-35-SA to the flange. To find the correct hub/drum for your spindle we'll need to know the bearing/grease seal part numbers. You can remove the current hub and check to see if the part numbers...
  view full answer...


• Determining The Correct Replacement Bearings And Grease Seal For A Keystone Cougar 29RLI
• Hey Curtis, You'll want to jack up one side of the trailer and remove the wheel and hub in order to get to your bearings, grease seal, and spindle. When removing the hub you'll first take out the outer bearing. When you take the hub off and flip it around you'll see the grease seal, which will cover the inner bearing. You can use a seal puller or a flathead screwdriver and hammer to pop the old grease seal out to see the inner bearing. Taking the grease seal out will ruin it so you'll...
  view full answer...


• Bearing Kit that Fits 2000 Yacht Club Motorcycle Trailer
• Hey Lance, we are pretty sure that the correct Bearing Kit is part # BK1-150 which has bearing numbers # L44649 for inner and outer but we would have to recommend you double check by pulling the bearing out or measuring the spindles where the bearings ride. They would need to be 1.06 inches for both bearing surfaces.
  view full answer...


• Could 2006 LoadRite Snowmobile Trailer Use 3,500 lb Trailer Axle Brakes
• Hey Frank, the 10 inch brake assemblies are tied to the 3,500 lb trailer axle so most likely the part # AKEBRK-35 would be what you would need but you'd want to make sure the brake pads are 2-1/4 inches wide on your current setup and there is a four bolt pattern that holds the flange to the trailer spindle. The bolt pattern is 2-7/8 inches apart vertically and horizontally.
  view full answer...


• Info Needed to Pick out Bearings for Four Winns Trailer
• We don't have a way to look up what your trailer axle would have but I can help you find it. You'd want to pull the hub off and either get the bearing numbers off the bearings or you could measure the spindle where the bearings ride. Due to age of your trailer there is chance it has parts that aren't available.
  view full answer...