Although we do not have a package I would be happy to make a recommendation. The Curt # C11391 you looked at is the best option for a hitch on your 2014 Honda Civic SI. This is a Class I hitch with a 1-1/4" and a bolt-on installation.
For a Class I compatible bike rack I recommend the Hollywood Racks Destination Bike Rack for 2 Bikes # HLY94FR. This platform style rack is lightweight at 20 lbs and has a weight capacity of 35 lbs per bike. It comes with an locking anti-rattle hitch pin... view full answer...
No, there is not, sorry. The only hitch that fits the 2019 Honda Civic is the Curt item # C92UR and it does not fit the ones with center exhaust.
If you are looking to haul extra gear or a bike rack the Rhino-Rack ROC25 Roof Rack for Naked Roofs item # RR78TR you were looking at are confirmed to fit the 2019 Honda Civic Hatchbacks. view full answer...
Hey Anthony,
Yes, the Curt Trailer Hitch Receiver # C92UR is designed to fit both hatchback and sedan models of the Honda Civic from 2016 - 2024, excluding models with a center exhaust. With your model not having a center exhaust you'll be good to go with the # C92UR and can follow along with Brad's installation video below to get this installed at home. view full answer...
Yes it can change, which is why it's required for you to load your trailer and then get it weighed. You can either take this to a scale to get weighed or use the etrailer Tongue Weight Scale for Campers and Utility Trailers # e99044 and o it yourself. view full answer...
When it comes to picking the correct WDS you're going to need to go off of the trailer your towing, rather than the tow vehicle.
To figure out what's going to work work best, you'll need to essentially load the trailer up with everything you'd bring/need for a trip and get the trailer weighed. What we are looking for is your total tongue weight, so after it's weighed you'll need to take a note of what that is.
From here you'll just need to pick a system that roughly puts your trailer's... view full answer...
Hey Stephanie, the Curt hitch part # C68DR is a great hitch for a cargo carrier to be used with your 2024 Honda HR-V.
For a cargo carrier you have two options. The flatter Curt part # C18110 which has a mesh floor and lower side rails or the Curt part # C18145 which has a railed bottom and a taller side rail design. These are only two options that fit this hitch size. view full answer...
Hey Richard, it sounds like you are looking for a high low adapter for when you will be flat towing your 2013 Honda CR-V. So the Blue Ox base plate kit part # BX2258 that fits your vehicle has a bracket height of 15-1/2 inches so you'd want an adapter that drops right at 5 inches or so. Keep in mind if you are within 3 inches of level you are okay at that point.
For that the Curt part # C59KR would work great as it can provide a drop of 4 inches.
We do ship to Canada as well ay. view full answer...
Yes, installation instructions for Curt trailer hitch # C11212 (no longer available) are linked on its product page, right hand side of the page. I have also included a link to them here for you.
This is a Class I hitch so if you are using it for a bike rack you are limited to 2 bikes at most and any accessory used has to be compatible with a Class I hitch. Also with Curt if you are using the hitch for anything other than a trailer you also have to use stabilization strap # 18050 per Curt's... view full answer...
Hey Rick, so I have a similar crossbar solution that will work for your 2024 Honda Ridgeline but we don't have any ladder racks that fit your vehicle's bed at all. Instead your best option would be a roof rack for that would put crossbars on the roof of the vehicle like the Thule Wingbar Edge part # TH28RE, # TH79SC, and # TH79RV. view full answer...
Hi there Bob; you can definitely back into the water to launch your dinghy using the CE Smith Multi Sport Plus Boat and Kayak Trailer # CE48870.
The hubs have a dust cap but aren't sealed so water can still get in them. To ensure no water gets in, I would replace that dust cap with the Bearing Buddy Bearing Protectors # BB1980A-SS.
As for the lights, they are fully submersible so no problem there at all, and there are no other limitations preventing the # CE48870 from getting backed into... view full answer...
If you only bought the adapter the first thing you're going to need is an actual 4-way on your 2010 Honda Odyssey. The # 118438 will plug into the connection point in your rear cargo area. Once this is done, you can plug the 4-way end into your 7-way adapter to carry over the signal functions for your trailer.
After that, you will need the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers # 5506. This comes with everything you need to complete the installation of your... view full answer...
Hey Roger, yes you could remove the trim of the High Pointe Built In Microwave part # HP84ZR and it could sit on a counter top like you asked about. The dimensions listed for it are correct for without the trim kit:
19" W x 11.375" H x 14.8" depth view full answer...
The Hopkins 7-way bracket part # HM48625 does not come with hardware and there isn't a set hardware size we can recommend for it but we do have the similar Pollak 7-way part # PK12711U which comes with small machine screws and nuts. I would recommend getting something similar but also it really depends on what 7-way you have. The 7-way may have hardware for this already included as well.
The size of what comes with the Pollak is four 3/16" x 5/8" long screws, four 3/16" nuts, and two... view full answer...
Great question, Gene!
The Draw-Tite Max-Frame Trailer Hitch Receiver # 76128 won't fit your 2023 Honda CR-V Hybrid but you can use the Draw-Tite # DT79MR instead.
I actually like the part # DT79MR over the one you referenced anyways because this style has a hidden crosstube so it not only looks better but it also has better clearance.
Attached is an installation video and a photo of this hitch installed on a 2022 CR-V for you to check out! view full answer...
Ben, the rack you're looking at is not going to work with your 2021 Odyssey, unfortunately. The bars itself will be able to be transferred between vehicles, but the legs and fit kit will not.
You'd need to also get the Rhino-Rack RT-Style Roof Rack Tracks - Rivet Mount # RRRTV168, the Roof Rack Leg Spacer Blocks for Rhino-Rack Vortex Aero Crossbars # RRQMVA10, and the Rhino-Rack Quick Mount Legs for Vortex Aero Crossbars # RRRLT600.
This can be a pretty involved process for someone who... view full answer...
Hello Martin, thanks for providing those measurements. I can confidently say that yes, the Thule Pulse Large Rooftop Cargo Box # TH615 will fit on your 2023 Honda CR-V. The Pulse Cargo Box will fit crossbar spreads between 23-5/8" - 34-3/8", so you are good there. In order for the hatch to fully open you will need at least 46-3/8" from the middle of the front crossbar to the hatch. Since you have 47 or 48", the hatch will fully open with about an inch or so to spare. view full answer...
For a 2 inch hitch for your 2015 Honda CR-V that would work great with a 4 bike rack you'd want the Draw Tite part # 75742 which is a confirmed fit. Of all the 2 inch hitches we offer for your 2015 Honda CR-V this one has the best capacities and price.
My favorite bike rack to recommend is the Thule Swing Away Bike Rack # TH9027XT because it can carry up to 4 bikes and can swing out and away from the rear of the vehicle to give you complete access to the rear cargo area with bikes loaded.... view full answer...
To flat tow your 2013 CR-V behind your motorhome you're going to need quite a bit of stuff.
To start off you'll need a base plate kit # BX2258, which will install onto your CR-V and provides a mounting point for a set of tow bars # e47ZR.
Next, you're going to need a braking system # BLU37TR with the 12 volt outlet kit # RM-9332. This part is pretty self explanatory, it's just a braking system meant to stop your towed vehicle in proportion with your motorhome.
Finally, you'll need a... view full answer...
Hello Kevin. The straps on the Saris Bones EX 2 # SAR83FR will be just fine if they make contact with the roof extension on your 2022 Honda HR-V. The straps are anchored to the hatch, so most of the strain will be there instead of the roof extension. Even with the loaded weight of the bikes you will not be in danger of breaking anything. Saris actually shows an example in their instruction of this rack on a car with a similar roof extension which you can see below.
The straps are designed... view full answer...
The hardware that installs the etrailer hitch part # e98840 shoudl be torqued to 139 ft lbs of torque. If you need a torque wrench we have the part # ALL944001 or sometimes you can borrow them from local auto parts stores. view full answer...
Go To Results