Parts Needed to Complete Installation of 7-Way Adapter on 2010 Honda Odyssey
Question:
Hi there, I bought a Rockwood trailer that has electric brakes. I have a 2010 Odyssey without the tow package. I purchased the 4 way to 7 way connector and the Curt bluetooth brake controller. My question is how do I connect the brake and power wires from the 7 way connector to my van? Thank you
asked by: Angela C
Expert Reply:
If you only bought the adapter the first thing you're going to need is an actual 4-way on your 2010 Honda Odyssey. The # 118438 will plug into the connection point in your rear cargo area. Once this is done, you can plug the 4-way end into your 7-way adapter to carry over the signal functions for your trailer.
After that, you will need the Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers # 5506. This comes with everything you need to complete the installation of your 7-way adapter. If you have the Curt Echo Under-Dash # C27JR you will need to connect the 12V power and brake output wires. If you're using the Curt Echo # C51180 you do not need to connect the blue brake output wire since it installs at the 7-way.
I have attached some installation videos below for your reference.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Curt Echo Under-Dash Bluetooth Brake Controller w/ OneControl App - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Under-Dash Box
- Hidden
- Up to 4 Axles
- Smartphone Display
- CURT
more information >
Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Trailer Brake Controller
- Proportional Controller
- Hidden
- Up to 2 Axles
- Smartphone Display
- CURT
more information >
Product Page this Question was Asked From
Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector
- Trailer Wiring
- Wiring Adapters
- Single-Function Adapter
- 0 - 5 Feet Long
- 4 Flat
- Plug and Lead
- 7 Round - Blade
- Tow Ready
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is Required to Use Curt Echo Trailer Brake Controller
- Article: My Trailer Hitch Doesn't Fit
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: 2024 Ford Maverick Wiring Needed for Flat Towing Behind a Motorhome
- Q&A: Could Buyers Products Hitch Plate part # 3371809061A Fit 1999 International
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Q&A: Converting a 4-Way Trailer Connector to a 7-Way on a 2014 Toyota FJ Cruiser
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Hidden Hitch that Fits 2019 Honda Odyssey
Angela
4/17/2024
Thank you Robin. My Odyssey already has the 4-way connector installed. I'm trying to install the 7-way but need to also install the brake wire as the trailer I purchased has electric brakes. I bought the Curt C51180. So my question is where do I install the blue brake wire from the 7-way connector into my vehicle? I was hoping not to have to drill or run wires, hence why I bought the Curt C51180.