You need the Replacement Hardware Kit for Trailer Hitches Item # RHK to install the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 76034 on your 2014 Ford Explorer. As far as a wiring I recommend the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector Item # C56278. This harness plugs directly into factory plugs, located under the vehicle, on the passenger side. I recommend using Dielectric Grease for Electrical Connectors, 2 oz. Item #... view full answer...
We have the Replacement Mounting Hardware Kit # AABRKT-3059 for the Aries Grille Guard # AA3059. This is the grill guard which is specific to the front of your 2006 Ford Explorer. If you have a different grille guard the mounting hardware may not allow you to install it as the mounting points on the grille guard may be different. view full answer...
To get the right replacement lock core for your Yakima cable lock take a look at the key. There should be a number on the key. If you can tell me that number I can tell you which is the correct lock core.
That is unless you do not need that lock to match any other locks. If that is the case you can get lock core set # Y07202 which includes 2 lock cores, 2 matching keys, and the all-important Control key used to install and remove lock cores. view full answer...
We definitely have replacement options for a 4 Flat on your 2013 Ford Explorer. I am including a full replacement for your T harness, as this is what I suggest doing, but also an option to cut off the end of your 4 Flat and splice on a new end.
The Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat # 118540 will be a full replacement for your damaged harness. This is a plug and play harness that will take at most 10 minutes to get installed. Due to all this, I recommend going this... view full answer...
It sounds like you have an older style BigHorn 4 bike rack that has a threaded insert that cannot be removed. If this is the case, you will want to use the Replacement Hitch Bolt and Clip # Y8890200. This threaded hitch pin installs the rack on the trailer hitch using a 15/16 inch socket.
Yakima has confirmed this hitch pin is the correct replacement for older BigHorn racks for 2 inch hitches that were made before 2004.
The Replacement Hitch Bolt, Nut, and Clip # Y8780022 that you referenced... view full answer...
Trailer wiring from a Ford Edge is not the same as what fits a 2020 Ford Explorer like your Limited model so you would need a new kit that fits your vehicle like with the Curt # C56093 which installs easily by plugging inline with taillights.
For a hitch I would recommend the mostly hidden Curt part # CU78FR which is also priced great and has plenty of towing capacity. view full answer...
According to Thule, who manufactured that box, the mounting holes in the underside of that box should be about 4 inches apart. If that's indeed the case, the # TH02943 would be the correct U-bolt. view full answer...
Yes, the converter section for the Progressive Dynamics panel part # PD4575K18LS8 (current part number for the # PD4575A) that your customer has is available separately with the part # PD4575CSV. view full answer...
The Yakima EXO Swing Away 2 Bike Rack # Y34ZR that you referenced comes with basically a random set of matching SKS lock cores but if you let me know what number you have I can let you know which cores you'd need. view full answer...
To order the replacement hardware for the Draw-Tite # 75096, you'd use part # RHK, and on the page you're redirected to type '75096' into the provided field, then choose 'Draw-Tite' from the drop down menu. Here's a parts breakdown of what's included:
6 ea 1/2-13 x 1-3/4 Grade 5 Carriage Bolts
6 ea 1/2 inch plated lock washer
6 ea 1/2-13 grade 5 hex nut
2 ea 1/4 inch x 1-1/2 x 2 inch block washer
2 ea hitch to frame adapter brackets
I hope this helps! view full answer...
Westin has several running boards for the 2004 Ford Explorer:
# 27-6135-1345
# 27-6130-1345
# 27-0015-1345
# 27-0010-1345
All of them use custom brackets # 27-1345. Provided you have one of the running board sets listed above the replacement bracket kit will fit. view full answer...
According to Blue Ox the base plate kit part # BX2668 does fit the versions of the Ford Explorer Sport that have the Active Cruise Control. I attached a picture that I took from the install instructions that shows where it says "Includes ACC" which means active cruise control. view full answer...
What brand bull bar do you have for your 2014 Ford Explorer? Both bull bars and mounting hardware kits are vehicle specific so you'll need to make sure that both are designed for your Explorer to ensure that everything fits.
For example, the Aries Bull Bar # AAB35-3013 that fits your '14 Explorer would use the replacement hardware kit # AABRKT-35-3013. view full answer...
The 2010 Ford Expedition should have a round connector at the rear of the vehicle where your 4 pin plug is plugged in. If there is a round connector there you can use the Replacement Multi-Tow 7-Way and 4 Pole Trailer Connector, item # 74682, to replace the 4-Way OEM connector on your Expedition.
If your Expedition does not have the mating round connector under the rear of the vehicle you will need to use a 4-Way to 7-Way adapter like item # 37185, to provide a 7-Way connector at the rear... view full answer...
I spoke to my contact at Westin and the correct replacement hardware kit you would need for your Westin Bull Bar # 33-0970 would be the part # 33-097PK. view full answer...
We have the correct replacement key you'd need with the part # THKEYN2854. To get the old key out you might try some smaller tools to grab what's left of the key and extract it. A locksmith would be able to help if you get stuck. view full answer...
For a replacement 7-Way trailer connector that will fit your 2012 Ford Explorer I recommend # C56278 because # 118242 is designed for certain Ford trucks but not the Explorer.
The replacement 7-Way, # C56278, includes the connector itself and a new harness that just plugs into the factory connector in place of the old one. view full answer...
The Replacement Endcap for Westin Sure-Grip Running Boards # 80-0221 are held in place with a #8-18x.50" phillips head screw. We do not carry this screw but you can obtain this from any local hardware store. You will want to line up the holes in the running boards with the brass fittings on the end cap and then attach with the sourced screws mentioned above. view full answer...
I see exactly what you are talking about. I checked the stock we have on hand and all of the # 118241 wiring harnesses have the pins in the 3 O-clock and 10 O-clock positions with the locking tab up. I then spoke with our installation tech and he feels that the directions for the 1999 Explorer are wrong. He says that he remembers having to use the connector that is on the drivers side and that the picture on our web page was taken following the manufacturers directions and never got corrected.... view full answer...
It looks like you need replacement hitch bolt, nut and clip # Y8780022. It fits into a 2 inch or 1-1/4 inch shank to provide anti-rattle capabilities of certain present and discontinued Yakima bike racks including the BigHorn, KingPin, BackSwing, FullSwing, and SlickROC. Yours looks like an early BigHorn. view full answer...