Expert Answers about Dodge Durango
- How Does Install Hardware Thread Through Frame for Trailer Hitch for 2017 Dodge Durango
- The method to get the bolt and spacer through the frame of your 2017 Dodge Durango is called "fishwiring" which you can see the entire process outlined in the install video link I attached.
view full answer... - Will AO Coolers Saddlebag Coolers Keep Food Warm
- Yes, the insulation on the AO Coolers Saddlebag Coolers # AC43FR will also keep things warm. These are a great solution for your food deliveries. As you said though, extremely hot items like something straight out of the oven would damage the cooler so it is not advised.
view full answer... - Does Hitch Need to be Replaced on 2015 Dodge Durango Involved in Collision
- If the OEM hitch on your 2015 Dodge Durango took the brunt of the damage to the point the safety chain loops were bent then that leads me to believe there could very well be other damage to the hitch and you'll want to look for places where the paint is chipping away or you see any stress fractures.
It might be best to just swap out to an aftermarket trailer hitch like the Draw-Tite # DT38MR so you know the hitch integrity hasn't been compromised but you might wait to see what your shop...
view full answer... - Factory Connection Points to Add Trailer Wiring and a Brake Controller on a 2005 Dodge Durango
- If you are talking about the connection point for a brake controller then you can find the factory connection underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
If you are talking about adding a 7-Way, the factory connection point for a 7-Way trailer connector on a 2005 Dodge Durango is located behind the rear bumper or along the driver side frame rail on the drivers side of the vehicle. There will be a rectangular plug. You...
view full answer... - Can E-Track be Driven Over In Trailer
- E-track like the part # e62VR will easily handle being driven over. It will not crush the track. Since it's a wood floor application I would recommend the Snap Loc Etrack Wood Screws part # SL49FR. I would use a screw in every screw hole.
view full answer... - Parts Needed to Install a Curt Venturer Brake Controller in a 2013 Dodge Durango with OEM 7-Way
- Since your 2013 Dodge Durango has the factory installed 7-Way, to install a brake controller you will just need the brake controller itself and the proper wiring harness to plug it into your Durango.
If you want to go with the Curt Venturer, # C74VV, then the only other part you will need is wiring harness # C51446. I have included a link to the installation details for you.
The wiring harness plugs into a connector already on your vehicle. The connector is located underneath the dash,...
view full answer... - Is Any Bumper Trimming Required to Install a Draw-Tite Trailer Hitch on a 2011 Dodge Durango
- You will not have to do any fascia trimming to install Draw-Tite Trailer Hitch # 75713 on your 2011 Dodge Durango. I have included a link to the installation instructions for you to view.
f you plan on doing some towing I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clips, and a carrying bag. For trailer wiring, use # 118552. I have included instruction links for the wiring as well.
view full answer... - Does Hopkins Tail Light Converter Require Power From Battery?
- The Hopkins Tail Light Converter Kit with 4-Pole Flat Trailer Connector # HM48925 does not have a wire to tap into from your vehicle's battery. It is designed so you can spice into the taillight wiring harness at the rear of your 2005 Dodge Durango. I have attached the installation instructions for you to take a look at.
view full answer... - How Brake Controllers Work and Parts Needed for Installation on a 2004 Dodge Durango without Tow Pkg
- There are two different brake controller systems that can be used. The Older style is the Time delayed style of brake controller, like the Draw-Tite Activator Trailer Brake Controller, item # 5504. This controller will get the signal from your brake pedal and then apply the trailer brakes at a, user set, pre-determined level no matter how fast the vehicle is stopping. There is also a delay setting so that the trailer brakes can be set to activate shortly after the vehicle brakes so they...
view full answer... - Is Bumper Modification Required to Install a Front Mount Hitch on a 2003 Dodge Durango
- We have front mount trailer hitches available for the 2003 Dodge Durango as long as it is a 4WD model. At this time there are no front mount hitches available for the 2WD models.
If you have a 4WD model, then I recommend installing the Curt Front Mount Hitch, # 31080. This has the highest vertical pull rating of our front mount hitches and it does not require any bumper modifications. The receiver will sit just below the front bumper fascia. I have attached the installation instructions...
view full answer... - Trouble Locating Green Wire To Connect To 12 Gauge Blue Wire In Tekonsha 7-Way Harness
- For the 12 gauge blue wire connection you will not have to remove the liner completely. You will only need to remove enough of the screws to allow you to be able to find the connector inside the fender well.
Many have trouble finding this connection and if you wish you can actually run the wire another way. The wire is simply the factory brake output. A simpler way of running the wire would be to run it into the vehicle and connect it to the blue wire on the brake controller harness....
view full answer... - How Often Should You Grease the Curt RockerBall Gooseneck Hitch Ball and With What Type of Grease
- For the Curt RockerBall Shock Absorbing Gooseneck Hitch Ball # C67DR, you will want to use a high quality molybdenum-based grease. You will want to grease prior to initial use and once every 3 months or 3,000 miles.
view full answer... - Trailer Wiring Tail Light Converter for a 2005 Dodge Durango
- The Tow Ready wiring harness # 118390 plugs in line with the vehicle tail light wiring and then runs to a converter box that takes the signals used by the vehicle and converts them to the signals used by the trailer.
Trailers have combined turn and brake lights some vehicles do and some do not. Others are a little less cut and dry. What this harness does is take the more complex signals used by the vehicle and translates them to work with the simple functions on the trailer.
This harness...
view full answer... - How Would The Westin Sportsman Grille Guard, # 40-0145, Install On My 2000 Dodge Durango
- This Westin Sportsman Grille Guard, 1-Piece Black Powder Coated, part # 40-0145, would install onto the bumper brace bolts on the outside of the frame on your 2000 Dodge Durango, you will need to be underneath your Durango to access this area.
.
view full answer... - What Causes Grease Leaking Out of Bearing Buddy Bearing Protectors
- It sounds like you just simply overfilled the Bearing Buddy Bearing Protectors like part # BB1980A but not to worry, they do this by design so you didn't damage anything. The built-in pressure relief valve will allow grease to seep out the piston to avoid damaging the grease seal. I'd wipe away the extra grease and then just proceed as normal, there may be still some more that seeps out. Just be careful not to overfill the hubs next time, you'll want a bit of movement when you press on...
view full answer... - Installing Base Plate Kit and Wiring on 2015 Dodge Durango for Flat Towing
- The Blue Ox Base Plate Kit # BX2411 that you were looking at is confirmed to fit your 2015 Dodge Durango, whether or not it features Adaptive Cruise Control. We haven't had a chance to install this particular kit, so we don't yet have a video available. I did attach the full install manual though that you can look through for reference. I have also attached an image that shows what tools you will need to have on hand.
For a lighting solution on the Durango I recommend the Roadmaster Diode...
view full answer... - Hidden Trailer Hitch and Trailer Wiring Harness for 2019 Dodge Durango
- The trailer hitch for your 2019 Dodge Durango which is hidden more than any other is the Draw-Tite Trailer Hitch # DT38MR. I have added a couple photos of the hitch installed on a 2019 Durango for you which display just how concealed the hitch is. I have added a link to a video install of this hitch on a '19 Durango for you to check out as well.
For a wiring harness, the best option is the T-One Vehicle Wiring Harness # 118617 because we have found that the manufacturer, Tekonsha, makes...
view full answer... - Can the Prodigy P3 # 90195 be Installed with Velcro on a 2018 Dodge Durango
- The factory 7-Way would have come with your 2018 Dodge Durango since you got the Class IV Towing Package. The factory 7-Way is a connector at the rear of your Durango near the bumper. I have attached a picture to demonstrate what it will look like.
You will be able to install the Prodigy P3 # 90195 with Velcro instead of the included mounting brackets if that is what you wish to do. As long as it is secure and is mounted on a horizontal (side-to-side) plane then you are good to go. The...
view full answer... - Wiring Guide for Roadmaster Universal Hy-Power Diode Wiring Kit # RM-154
- Based on my research both your 2002 Bounder motorhome and your 2000 Dodge Durango have combined brake/turn lights. So in this case you will wire the Roadmaster Universal Hy-Power Diode Wiring Kit # RM-154 as shown in the linked wiring diagram.
view full answer... - Will the ETBC7 Provide Reverse Lockout Functionality on 2017 Dodge Durango for Boat Trailer
- Adding a 7-way connection with the # ETBC7 Universal Installation Kit will provide you with the reverse lockout you need to make sure the brakes do not engage in reverse. Since it sounds like you have a 5-way connection on your boat trailer, you will also need an adapter like the Hopkins Endurance, Flex-Coil Trailer Connector Adapter - 7-Way to 5-Way or 4-Way Flat # HM47075. This would allow you to plug your 5-way connection from the trailer into the 7-way connection on your vehicle.
Another...
view full answer...
Go To Results