Expert Answers about Dodge Caliber

Replacement Screen Door Bubble Slider Panel For A 1996 Fleetwood Southwind
I went out to the warehouse, and measured the Lippert Motor Home Entry Screen Door Bubble Slider Panel # LC234101 that you inquired about. This item, along with the Replacement Slide for P-Series RV Screen Doors # A77019 you mention, have the same thickness at 2.24mm, and the same depth of 1-1/4". Unfortunately, all of our slider panels are going to be around the same thickness of 1-1/4".
view full answer...

Roof Rack Recommendation for 2012 Dodge Caliber for Small Cargo Box
For your 2012 Dodge Caliber we have one roof rack option. The Inno square roof rack part numbers # INB127, # INSUT, and # INK555 which would do a great job to carry a small cargo carrier as long as it's compatible with the smaller crossbar spread of this rack. The part # MPG901 would work and provides 12 feet of cubic space.
view full answer...

Thule Raceway 3 Bike Carrier Recommendation for a 2008 Dodge Caliber
Yes, the Thule OutWay 3 Bike Carrier, part # TH56BV, is a confirmed fit for your 2008 Dodge Caliber. As long as the weight of your 3 mountain bikes does not exceed the weight capacity of 99 lbs that this rack has you could carry your 3 mountain bikes easily and comfortably.. If you plan on carrying women's or alternative framed bikes I would recommend you get a Thule Bike Adapter Bar, part # TH982XT.
view full answer...

Which Trailer Hitches Will Fit a 2008 Dodge Caliber R/T
The good news is we have a hitch that will fit a 2008 Dodge Caliber R/T. The Curt Trailer Hitch, # C11006. This is a Class I hitch, 1-1/4 receiver opening, 200 pounds tongue weight capacity, 2,000 pounds gross trailer weight. I have included a link to the installation instructions below. The Draw-Tite trailer hitch has some subtle differences in terms of where it mounts and how it is designed which is why it will not fit the R/T model.
view full answer...

What Would Cause Transmission To Seemingly Stop Shifting Properly When It Warms Up
I've had similar issues with cars and the problem wasn't that the temperature of the fluid was causing the change in shifting/performance the issue was that the fluid filter was getting clogged with debris (from clutches etc. failing and coming apart in the transmission) and therefore not able to allow the transmission to shift properly. Once you park the car the debris falls off of the filter and it appears to shift normal again till it clogs again. The solution is to take the vehicle...
view full answer...

Will Curt Class I 1-1/4 Inch Hitch # C11006 Fit a 2007 Dodge Caliber R/T AWD Model
I spoke with my contacts at both Draw-Tite and Curt, who both confirm that their Class I receiver hitches # 24769 and C11006 will fit the 2007 Dodge Caliber R/T AWD model as long as it is not an SRT-4 model. Although both hitches look very similar and have the same weight bearing capabilities, I would recommend the Curt model due to its additional mounting points. In my opinion, the two additional mounting locations would make for a stronger installation. I will provide links to the installation...
view full answer...

2008 Dodge Caliber Class I Hitch Bike Rack Recommendation
The Swagman XC2 Bike Rack # S64650 will technically fit the 1-1/4" receiver opening of the Class I Draw-Tite Sportframe Trailer Hitch # 24769 on your 2008 Dodge Caliber, but Swagman has tested and deemed that a Class I receiver isn't strong enough which is why it is rated for a Class II hitch. As an alternative I recommend using the Malone Runway Bike Rack for 2 Bikes # MPG2149 instead. The Runway bike rack can hold 33 lb bikes as opposed to 35 lb bikes like the Swagman XC, but everything...
view full answer...

Recommendations for Carrying a Dirt Bike with a 2007 Dodge Caliber R/T AWD
The only trailer hitches available for a 2007 Dodge Caliber are Class I trailer hitches that have a 1-1/4 inch receiver opening. They also have a 200 pound tongue weight capacity which is not going to be high enough to support the weight of the bike and carrier. A higher capacity hitch is not available because the vehicle cannot support the weight. Make sure to consult the vehicle owners manual in the towing section to determine the towing capacities of your Caliber. What I recommend...
view full answer...

Correct Installation Kit for a Westin Safari Light Mounting Bar
The brackets we have for a Westin Safari Light Mounting Bar item # 30-0025 is the Custom Installation Kit for Westin Safari Light Bars item # 30-1345. This bar will only fit the following vehicles: 2002-07 CHEVROLET TRAILBLAZER 2002-04 GMC ENVOY 2003-07 ISUZU ASCENDER 2004-07 BUICK RAINIER and OLDSMOBILE BRAVADA It does not fit a 2008 Dodge Caliber nor is there a light bar or bull bar that is custom made for this type of vehicle.
view full answer...

Best Lock When Carrying Schwinn Clear Creek on Swagman XTC2 Bike Rack Is Frame Adapter Needed
I took a look at the Schwinn Clear Creek online, and am convinced that the upper frame bar doesn't plunge down so far that the frame hook of the bike rack wouldn't be able to hold it. You should be okay without using a frame adapter. As far as a lock goes, Swagman offers a combo hitch/cable lock part # S64031 that will secure the rack to the hitch and the bikes to the rack. No lock is completely foolproof, but this item will certainly deter theft and encourage would-be thieves to find...
view full answer...

Does the Drawbar Included with the Hidden Hitch Trailer Hitch # 60832 Have a Hollow Shank
I went out into our warehouse and inspected the drawbar that comes included with the Hidden Hitch Trailer Hitch Receiver with Drawbar - Custom Fit - Class I - 1-1/4 inch, part # 60832 (no longer available), and it has a solid shank. The included Class I drawbar, that is designed for 1-1/4 inch, hitch openings has a tongue weight capacity of 200 lb, and gross trailer weight limit of 2000 lbs. You may also need a Tow Ready Custom Fit Vehicle Wiring for the Dodge Caliber, 2007, part # C55050,...
view full answer...

How to Determine Correct Ball Mount for Tow Vehicle and Trailer.
In order to choose the correct ball mount for your tow vehicle and trailer, you will first need to take a couple of measurements. With your tow vehicle parked on level ground, take a measurement from the ground to the top of the trailer hitch receiver. Then with your trailer on level ground, measure from the ground to the bottom of the coupler. If the hitch height on your vehicle is greater, you will want to find a ball mount with a drop. If the coupler height is greater, you will want...
view full answer...

Is Installation of the Power Wire Required for Trailer Hitch Wiring on a 2007 Dodge Caliber
The T-One Vehicle Wiring Harness, # 118552, for a 2009 model Caliber or the Curt # C55050, for a 2007 Caliber, powers the trailer lighting from the vehicle battery. If you do not connect the power wire to the vehicle positive battery post, the harness will not function properly and the vehicles sensitive wiring and circuitry would be at risk of damage if a short circuit would occur on the trailer wiring. The black converter box serves several functions. First, it senses when the brakes,...
view full answer...

Would a Transmission Cooler Help a 2009 Dodge Caliber that Whines After Warming Up on Hills
Transmission coolers do an excellent job keeping the transmission fluid cool to prevent damage from happening, but if your transmission already has problems it won't fix the issue. Your best option would be to take your vehicle to a qualified transmission repair shop and let them diagnose the noise your vehicle has. Once the problem is addressed I would then recommend installing a transmission cooler to prevent future problems as heat is the number one killer of transmissions. The part...
view full answer...

What Trailer Hitch Is Available For A 2007 Dodge Caliber R/T
We offer two hitches for a 2007 Dodge Caliber, as long as it is not an SRT-4 model. Anytime you are going to be installing a hitch to your 2007 Dodge Caliber R/T for towing purposes, you will need to check your owners manual for the vehicles maximum towing capacity. You will want to make sure that your vehicle will be able to handle the capacities of the hitch you will be installing. The Curt Class I 1-1/4 Inch Hitch, part # C11006, will fit a 2007 Dodge Caliber R/T. It has a maximum...
view full answer...

Will Tow Ready T-One Vehicle Wiring 118552 Fit a 2008 Dodge Caliber R/T
Yes, the Tow Ready # 118552 T-Connector is a fit for all models of the 2008 Dodge Caliber (except SRT4), and will work on your R/T model. The installation is fairly simple, as the wiring just plugs into the back side of the vehicle tail lights, between the light and factory wiring. You will also need to run the red power wire along the bottom of the vehicle and connect it to the positive terminal on the vehicle battery, with the included fuse and fuse holder in line. I would recommend...
view full answer...

What Is Maximum Tongue Weight For Draw-Tite Trailer Hitch, # 24769, For A 2007 Dodge Caliber
Anytime you are going to be installing a hitch to your 2007 Dodge Caliber, you will need to check your owners manual for the vehicles maximum towing capacity. You will want to make sure that your vehicle will be able to handle the capacities of the hitch you will be installing. The Draw-Tite Trailer Hitch Receive, # 24769, is a Class I hitch and has a maximum towing capacity of 2,000 lbs. and a maximum tongue weight of 200 lbs. The factory Class I hitch would have to be removed to install...
view full answer...

Block Heater for 2009 Dodge Caliber and Install Location
You can warm up the engine of your 2009 Dodge Caliber with the Kat's Heaters Custom Fit Engine Block Heater # KH11812, which is the correct fit. The location installation is in the front left, marked "FL" on the accompanying photo from the directions that I cut out for you. I've added a link to a video review for you to check out as well.
view full answer...

Ball Mount and Ball Recommendations for Draw-Tite Class I Trailer Hitch on a 2011 Dodge Caliber
I checked to see which hitch you ordered for your 2011 Dodge Caliber and it was Draw-Tite hitch # 24769. For Class I trailer hitches like this you are supposed to use the ball mount recommended by the hitch manufacturer. In this case it is # 3591 and the hitch instructions indicate it should be used in the rise position only (with the ball platform on top). A hitch pin with clip is included. If the trailer you will be towing takes a 1-7/8 inch ball you can use ball # 19256. And if it requires...
view full answer...

Can the CE Smith U Bolt # CE15253A Be Used to Mount the CE Smith Offset Spool Roller # CE32150G
The CE Smith U-bolt # CE15253A could be used to mount the CE Smith Offset Spool # CE32150G. The diameter of the u-bolt and the mounting bracket of the offset spool are both 7/16 inch, and are compatible. I have included a video demonstration of the CE Smith Offset Spool for your reference.
view full answer...