Expert Answers about Mazda 6

Does Camco Wave 6 RV Heater Require Regulated Propane
The Camco Olympian Wave 6 Catalytic Safety Heater for Mid-Sized RVs # CAM57341 is not designed to run off of unregulated propane. It needs LP gas which is regulated to 11 inches of water column. So you would need a regulator like the part # CAM57703 that you also referenced.
view full answer...

Replacement Rhino-Rack 062 Key
I have a solution for you. First, though, you need to know that Rhino-Rack does not make just replacement keys. They are sold with their lock cores. To get your 062 key, you will need the Rhino-Rack Masterkey Lock Barrels, part # RRRK062-2. I suggest keeping the lock cores as they can be used as replacements if they ever need replacing.
view full answer...

Rhino Rack Roof Rack Recommendation for a 2008 Mazda 6 4-Door
If you have the Rhino Rack 46 inch crossbar kit part # RRVA118B-2 and # RRRLKVA already all you would need is the correct fit kit to install it on your 2008 Mazda 6 4-door, part # DK043. With those three parts you would have everything you would need to install the rack.
view full answer...

Will Tekonsha T-One Wiring Harness # 118587 Fit 2016 Mazda 6 GT with LED Lights
Yes, the Tekonsha T-One Vehicle Wiring Harness # 118587 that you referenced is confirmed to fit and will work perfectly on your 2016 Mazda 6 GT with the LED tail lights. This custom harness will plug right into existing ports behind the tail light assemblies and receive power by running a hot lead up to the battery. This will provide you with the needed 4-Way connector for powering a trailer's basic signal lights. I have attached the full install manual below that you can also look through.
view full answer...

Recommended Bike Rack For A 2009 Mazda 6 With Curt Class 1 Hitch
The Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches # S64650 is rated for use on class 2 or 3 trailer hitches but unfortunately there are only class 1 trailer hitch receivers available for a 2009 Mazda 6. This bike rack will not work with class 1 hitches like your Curt # C11359. You would instead need a bike rack like the Saris Freedom Bike Rack for 2 Recumbents Bikes - 1-1/4" and 2" Hitches - Frame Mount # SA4412B-R. This rack is rated for use on a class 1 hitch, but only has...
view full answer...

Is There Drilling Required to Install Curt Trailer Hitch # C11308
Yes, to install the Curt trailer hitch part # C11308 you will need to drill a 1/2 inch diameter holes. If you check out the attached install instructions you can see more info on the install of this hitch.
view full answer...

Which Thule 3 Bike Trunk Mount Bike Racks Will Fit a 2011 Mazda 6 Sedan
Yes, according to Thule the OutWay 3, # TH56BV, will fit your 2011 Mazda 6 sedan. Thule has several 3 bike trunk mount bike racks that will fit your car. Gateway 3, # TH78VR Passage 3, # TH910XT Out of all of these bike racks, I think the Raceway 3 is the best choice. It is very light weight, under 19 pounds, and the retractable cables make it quick and easy to install. Out of all of the trunk mounted bike racks I have used, the OutWay has been the easiest to install. I have included...
view full answer...

Trailer Wiring Harness Recommendation for 2016 Mazda 6
The Tow Ready # 118587 is the Trailer wiring harness I'd recommend for your 2016 Mazda 6. The installation is mainly plug and play, the harness will plug in on the driver's and passenger side, inline between the vehicle's taillight assemblies and the wiring harness that feeds them. A wire will need to be ran under the vehicle up to the engine compartment, where the wire will connect to the positive battery terminal. The Curt # C11356 trailer hitch does not have a ball mount or hitch ball...
view full answer...

Will The Curt Class 1 Hitch C11356 Work With Other Bike Rack Brand Made For 1-1/4" Hitch
Yes, the Curt Class 1 Hitch # C11356 will work with the 1 up quik rack single that you mentioned. This hitch will work with any accessory made for a 1-1/4" receiver. It appears the quik rack will work with both the standard hitch sizes 1-1/4" and 2".
view full answer...

What 4-Way Flat Connector Is Compatible With My 2020 Mazda 6
The wiring harness that will fit your 2020 Mazda 6 is the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part # C56300. It comes with a custom wiring harness that will plug into your existing wiring, no splicing necessary. The T-One wiring harness you attached to your question will not fit your vehicle. I have included a product description link and a video installation of this item on a 2020 Mazda MX-5 Miata, which will be similar, below.
view full answer...

E-Bike Rack Recommendation that Can Fit Class I Hitch of 2016 Mazda 6
Yakima bike racks that fit the 1-1/4 inch hitch size only can fit the Class II hitch which for your 2016 Mazda 6 there is only a Class I hitch available like the Curt # C11356. So the best bike rack solution would be the Thule EasyFold XT # TH903202 which is Class I compatible, has a ramp setup that pulls out, and has the higher capacity needed for E-bikes since it is an E-bike rack. I attached a review video for this rack for you to check out as well.
view full answer...

Class I Trailer Hitch for 2017 Mazda 6
We offer the light-duty Class I hitch for your 2017 Mazda 6, the USA-made Curt # C11356. Both share the same no-drill installation with included hardware, and you can see the whole installation in the video I linked for you. For a 4-pole wiring harness you can use # 118587, for a ball mount # C45016 and for a hitch ball part # A-82 for a 2-inch ball or # A-80 for a 1-7/8-inch. Be sure to check your Mazda owner's manual before towing.
view full answer...

Recommended Trailer Hitch/Cargo Carrier For A 2019 Mazda 6
The Curt Trailer Hitch Receiver # C11356 is confirmed to fit your 2019 Mazda 6. The trailer hitch has a maximum tongue weight of 200 pounds. The trailer hitch has a bolt-on installation with no welding required. I recommend the class 1 cargo carrier, the 17x46 Curt Cargo Carrier # C18145. The trailer hitch can only haul up to 200 pounds and the carrier weighs 25 pounds, which gives you 175 pounds you can haul, depending on what your vehicle's maximum tongue weight is. This can be found...
view full answer...

Will the Thule Passage 3 Trunk Mounted Bike Rack fit a 2006 Mazda 6
Yes, the Thule Passage 3 Bike Carrier # TH911XT that you referenced will work on your 2006 Mazda 6 as long as it is not the hatch model. As long as you keep the contact points of the rack and your car paint clean and you do remove the rack when not in use you should not have a problem with the paint of your vehicle getting scratched. If you will be carrying womens, childrens, or alternative frame bikes, I recommend using the bike adapter bar, # TH982XT, for greater ground clearance and...
view full answer...

Will a SportRack Roof Rack Fit a 2010 Mazda 6
Yes, the SportRack semi-custom roof rack, # SR1010, is listed as a fit for your 2010 Mazda 6 sedan. It does not fit a 5-door model. I have included a link to a video review of this series of roof racks for you. If you have a 5-door model then there is one roof rack option from Rhino-Rack using the following parts: Euro Square Crossbars # RRVA126B-2 Feet # RRRLKVA Custom DK Pads # DK289
view full answer...

Hole Saw Size Recommendation for Installing the Draw Tite Hitch 24832
The recommended size hole saw to use to install the Draw Tite hitch part # 24832 is 1-1/8 inches. I also attached a link to the install instructions and video for this hitch for you to check out as well.
view full answer...

Position of Footplate Handles and Plunger Pins on Landing Gear Trailer Jacks
From what I have seen, there are 2 different configurations for landing gear jacks like # BD182815. First is like the jack you have referenced that has the foot release is perpendicular to the rod through the top center of the jack. The other configuration is like # BD182411, with the release parallel with the top rod. Jack # BD182411 is a companion to the Bulldog Square Jack # BD182400. The Bulldog Square Jack, # BD182404 and can be used in tandem operations with either of the first two...
view full answer...

SportRack Roof rack for a 2009 Mazda 6
If you have a 4-door 2009 Mazda 6 with no existing rails or crossbars, you can use SportRack Roof Rack, # SR1010, that you have referenced. I have also included a link to the roof rack main page for your vehicle for you.
view full answer...

Will Rhino-Rack Roof Rack Fit 2021 Mazda 6 With Fixed Mounting Points
So far for your 2021 Mazda 6 you have the following parts in your cart: Vortex 49" Crossbars - # RRVA126B-2 2500 Series Legs - # RRRLKVA Thule TopRide Bike Rack - # TH75JV Thule One-Key System - # TH450200 To complete this system you'll need the DK Fit Kit # DK387. This uses clamps that secure in the door jamb of your Mazda though so if you're wanting to utilize the fixed mounting points you'll need a different roof rack and for that I recommend the Yakima JetStream System. If you choose...
view full answer...

Thule Roof Rack Recommendation for a 2014 Mazda 6
There is a Thule roof rack available for your 2014 Mazda 6. All of the part numbers you referenced are the correct components needed have a complete Thule Aeroblade roof rack on your vehicle as long as you have a 4 door with a naked roof. I confirmed this with Thule.
view full answer...