We carry the Timbren 1" Spacer For Raised Frame Vehicles # TA25723-90AD00 which will help get you back into tolerance. We also carry the Timbren 1/2" Spacer For Raised Frame Vehicles # TA25722-90F00 if you'd like to get closer to the 1/2" mark and have the Timbrens activate sooner. view full answer...
I spoke to my contact at Wheel Masters about the Wheel Masters 2-Hose Inflation Kit part # WM8002 and they informed me that you won't have any issues using this kit with TPMS sensors. The reason for this is that the lines in this kit are pressurized up to the valve stem. If you were to use a set of non-pressurized line (airless) like the Wheel Masters Airless 2-Hose Inflation Kit part # WM80022 then that is where you would run into issues with leaking so use with TPMS sensors is not advised. view full answer...
Binding will not be an issue at all in a flatbed truck like yours when using the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter # CAB-C5G.
You just need to be sure you have enough space in the recessed location, as the cut out needs to be larger than 7 inches wide x 5 inches long, and so long as it is you're set, because those are the dimensions of the base on the # CAB-C5G. view full answer...
Yes, the Curt Class V hitch part # C15800 that you referenced is a confirmed fit for the 2021 Ram 4500 cab and chassis models like what you have. view full answer...
From the connection point to the end of the bend in the Wheel Masters 4-Hose Inflation Kit # WM8001-135 is approximately 1-1/2" in length. You could try sticking a tape measure in there and measuring out 1-1/2" at a 135 degree angle to see if it will clear the handhole in your wheels. view full answer...
I checked with TorkLift for you, and they do have a hitch that fits a 2022 Ram 4500 cab and chassis, with the correct fit being the following:
- TorkLift SuperHitch Magnum Trailer Hitch Receiver # TL49YR
Then, because of the overhang you mentioned, you do need the SuperTruss extension, the TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers - 42" Long # TLE1542. view full answer...
The B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1500 that you referenced is a universal application that is welded on to steel flatbeds when it comes to the installation. It isn't fitguided to fit your CM SK truck bed but as long as its steel you can reference the linked installation instructions to ensure fitment. I confirmed this with my contact at B&W. view full answer...
Yes, the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional # 90195 with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ram # 3024-P is a compatible replacement for your stock Ram 4500 brake controller. This custom wiring adapter will make installation a breeze. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your Ram 4500's dash. The Prodigy P3 automatically levels... view full answer...
Yes the Edge Juice with Attitude CS2 # EP31407 that you referenced is a confirmed fit for your 2018 Ram 4500 cab and chassis. This can provide up to 80 horsepower and 200 ft lbs of torque. view full answer...
The safety chains need to exceed the loaded weight of the trailer not the axle capacity. If the loaded weight of your trailer is significantly under 3500 lbs then a 3500 lb safety chain is fine. I have attached a link to all of the safety chains that we carry for your reference. view full answer...
The correct valve extenders for your 2023 Ram 4500 will depend on a couple of factors. First we'll need to determine the correct angle so that the extenders can sit properly and then we'll need to determine how they need to be mounted. If you have a hub cover to rivet the mounting bracket to then you can use the 90 degree # WM8001 or 135 degree # WM8001-135. For a hand hole mount you can use part # WM8009, and for a wheel cover mount you can use part # WM8208. view full answer...
Since we don't know for sure what you axle is I do recommend first contacting Dexter and to try and confirm exactly what kind of axle you have. If you haven't really looked at them I do recommend getting under the trailer and trying to find a tag because it will make this process much easier.
Assuming you have Dexter 10k general duty axles there will be two choices depending on the hub:
Option 1: Kodiak Disc Brake Kit # K2R1058D11HD, which uses the Dexter Trailer Idler Hub Assembly... view full answer...
There isn't a correct option for a slipper spring end type (radius or flat) for a 15k axle, or a particular fit for the Dexter Tandem-Axle Trailer Equalizer Kit for 3" Slipper Springs # HAP-203-03. Flat and radius ends are completely interchangeable and either will work just fine, you only need to make sure your dimensions are correct. Since you mentioned having a 15,000 lb axle and your spring is 30-1/2" long and 3" wide you can use either of the following:
- Dexter Axle 7-Leaf Slipper... view full answer...
Go To Results