Yes, you will need to cut off the 4-way connector from your trailer and wire the 5 wires to a 7-way connector like # PK12706. Test the function of the wires before connecting them to the 7-way. Refer to the diagram attached below to place the wires in the correct position. Check out the video linked below for more details.
If you need to add a 7-way to your vehicle as well, let me know the year, make, and model on your vehicle and any existing connectors you have, and I can make a recommendatio... view full answer...
To get the best weight distribution on your 2014 Chevrolet Silverado 1500 you first need to get the system set up for both the truck and the trailer.
1. Start by getting your trailer level, you can use a bubble level. Once level, measure from the ground to the top of the coupler. Note that measurement.
2. Measure from the ground to the lower edge of your fender on the back wheel and front wheel of your truck, straight up the center of the wheel and note that measurement. Make sure there... view full answer...
On the Furrion RV Cooktop - Propane - Triple Burner - Stainless Steel Item # FGH4ZSASS, if the flame is turned off on the stove, the stove is shut down. If the flame goes out and the stove hasn't been turned off then it will still emit gas to that burner. The knob must be turned off to stop the gas. Keep in mind this is going to be like any other gas appliance. You are still going to have gas in the line until you turn the gas off at the tank and release the gas from the line. The stove... view full answer...
The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # C56327 will not void any warranty you have on your 2020 Ford Transit T250. There was a bill passed that protects consumers from any type of cancellation of warranty when adding aftermarket components such as wiring harnesses. As long as the product you are using did not directly cause the issue there is no voiding that can be done.
I have linked an installation video for you if you would like to check it out. view full answer...
Red, black, and white wires are common on many tail light assemblies. When this is the case, you will have red as stop and turn, black as running light, and white as ground. So you will connect yellow to red on one side of the trailer and green to red on the other side. Then on each side you will connect white to your frame or mounting hardware, and brown to black for your running lights. I've attached a video of similar lights # STL69RB to assist.
If you need additional wire, use #... view full answer...
I have attached the complete instructions manual for the Thule T2 Pro XTR 2 Bike Platform Rack # TH83JV below which details both the assembly instructions and the correct bike loading process. Most of the rack comes pre-assembled and it's really just a matter of putting together a few of the components out of the box.
I have attached a short video demonstration on the Thule T2 Pro that you can also check out. view full answer...
Yes, you can install the Draw-Tite Ultra Frame Service Body Trailer Hitch # 41990 upside down. I spoke with my contact at Draw-Tite and he said that the top and bottom portions of the crosstube are identical in terms of construction/steel thickness so this won't be an issue at all.
You will just want to make sure that with it mounted in this orientation on your vehicle that you will still have access to the safety chain loops so you can easily attach the chains.
This heavy-duty weld-on... view full answer...
The Roadmaster Rear Anti-Sway Bar for Motorhomes # RM-1139-143 can use your factory u-bolts if they are long enough. If they are not, then Roadmaster recommends using the 7/8 inch diameter u-bolts that are longer (most likely the larger diameter due to length needed to ensure strength). I've attached a couple photos from the installation instructions to assist with the size and torque.
When torque specs are so large either a large special torque wrench is required or installers are... view full answer...
Are you using the RCA cables of the Furrion HDMI Stereo with Bluetooth, NFC, and App Control - 160 Watts - 2 Zone # DV3300SBL to connect to the TV or are you using the HDMI cable. If you are using the RCA cables that would explain the blurry picture as they do not carry a high quality video image. Instead you'd want to use the HDMI connection as that will be the only way to transmit a fully HD video signal. view full answer...
I spoke with my contact at Westin regarding the Perfect Match Series Rear Step Bumper # 31006 and he said that this is going to attach and install the same exact way as your existing factory bumper. With this in mind you will be able to retain the factory hitch without an issue. It might end up being easier to temporarily remove the hitch or some of its hardware while actually installing the new bumper but it shouldn't be necessary.
All of the necessary mounting hardware is included. view full answer...
If you are looking for an easy way to power the Everchill Refrigerator for RVs # 324-000119 on and off with a switch instead I have a better solution than trying to wire in a switch. Instead use a power strip with a switch. This basically requires no install time as you just plug in the fridge to the power strip and then the strip into the wall. The power strips also have ways to easily mount to walls which will be much easier than trying to reach around a fridge for a switch. view full answer...
The Tekonsha Primus IQ # TK90160 will only send power to the 5 o'clock pin of your 7-way when it senses a connection on that pin. The trailer connected needs to read on the controller for the controller to send any power. When a trailer with brakes is connected there is a slight power draw on that pin that shows the controller there is a trailer with brakes connected. If you simply want to test this without a trailer you will need a circuit tester like # PTW2993 and connect that probe... view full answer...
You'll want to use the amount of links that allows the tow vehicle to sit as close to level as possible. So in your case you'd want to use 6 links since you said that gives you the more level height. Since your weight distribution system is rated for 500 to 800 lbs and your tongue weight is 600 you're good in that regard as well. view full answer...
Yes, you can install the Furrion Observation System part # FOS43TASF on your 2019 Outback 340BH that has Voyager pre-wiring. The Furrion comes with the correct mounting bracket you can install in place of the Voyager one and the wiring on your trailer can be connected to the wiring of the Furrion easily. Basically the hard part of any install like this is running the running light circuit to the area the camera will be installed. Since in your case the running light circuit is already... view full answer...
The best place to mount the electrical connector is directly to the front bumper fascia, below the chrome moulding. I have attached a few photos of this for you as well on the Roadmaster Crossbar-Style Base Plate Kit part # RM-523198-4 but it shouldn't really matter which kit you have.
If you don't already have a flat-tow wiring harness for your vehicle then I recommend the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267 because it will then allow you to incorporate... view full answer...
The 2003 Dodge Dakota does not have a converter box as a part of the trailer wiring. Here is where confusion comes in and where ambiguity comes. Some LED lights may have zero issue plugging directly into the system based on the trailer length, ground connections, and number of LED's in each light fixture. Due to enough power draw.
Other trailers may not have enough power draw and may have hyperflashing issues requiring load resistors either on each line or through a converter like #... view full answer...
The heavy duty Rack and Roll shocks, part # Y08110, can only be used on 66 inch Rack and Roll if you upgrade it with the 78 inch crossmember kit. The crossmember kit is part # Y08111.
The 66 inch trailer is rated up to 250 pounds so as long as you're under that capacity there really isn't a need to upgrade it. It would just give you some peace of mind. view full answer...
I have the perfect option for you, but to address your specific question the Kuat Transfer 1 Bike Add-On, # TSAOB, should not take you an hour to install, but it certainly wasn't designed for easy on/off use. There are a total of 7 allen head bolts and 2 spacers that hold the add-on to the main rack. The add-on comes with the necessary allen wrenches and all of the hardware, so you won't need anything else.
If you are looking for a single bike rack with the easiest to install 2nd bike... view full answer...
The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat # MA00-06200K will install in the exact same cutout as the stock vent. You will simply need some sealant and screws. Many will choose to use the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White # 344270KITW. You don't absolutely need both butyl tape and sealant, so many will use the LaSalle Bristol XTRM Universal Self-Leveling Sealant - White - Qty 1 # 34427034145-1 or # 0160297 and then the Zinc Sheet Metal Screw... view full answer...
There is nothing internally on the Redline Locking "L" Style Door Handle # 276 that keeps it from rotating freely. This will turn more than 90 degrees as long as your existing locking system allows this.
This handle features a 2-1/2 inch long shaft that is 5/16 inch square. Two keys are included. view full answer...
Go To Results