The Adarac Pro Series Ladder Rack part # A4001671 is a fit for your 2008 Toyota Tundra 6-1/2 foot bed with a plastic bedliner and the deck rail system. view full answer...
Actually based on the tire size you listed you would want the part # TC3829CAM instead of the # TC3831CAM. This is the same style of chain that you referenced with the only difference being that it is confirmed to fit your tire size.
I attached a review video for you to check out as well as an FAQ article on snow chains. view full answer...
One of the longest ball mounts we offer is the Brophy ball mount part # BM20. This ball mount is 13-1/4 inches long from the center of the hitch pin hole to the center of the ball hole and has a 10,000 lb capacity. Without knowing how much capacity you need it's hard for me to say if this would be enough.
Backing up trailers is a bit of an art. The best advice I can give you would be to take your time and practice often. Also, it helps to have the trailer as straight as possible when... view full answer...
For a replacement towing mirror that can extend for an increased field of vision I would recommend the K-Source Towing Mirrors part # KS70104T that you referenced.
The telescoping arm extends the mirror out from your truck by almost 4" for an expanded field of vision. This heated power mirror also has a built-in turn signal. For the passenger side mirror you would want the part # KS70103T. Or to order them as a pair you would want # KS70103-04T.
I attached a review video for you to check... view full answer...
The colors of the wires of the # HM43385 may not perfectly match what you have on your 2004 Toyota Tundra, but as long as they functions match up (they should), this product would be exactly what you need.
You can verify that the connectors you found match pins of the diagram with a circuit tester like part # PTW2993. You will need someone to apply the different taillight functions while you test the pins with the connector. view full answer...
I have a solution that will allow you to continue using your weight distribution system and carry a bike but you can't use a dual hitch adapter with a weight distribution system. One solution is the bunk adapter for your trailer part # CC-275. This attaches to the a-frame of your trailer and then gives you the ability to carry a bike rack above it like what you see in the picture I attached.
Or you could attach a bike rack to the shank of your WD system like the Swagman Traveler XCS part... view full answer...
For your 2021 Toyota Tundra we have SumoSprings options that range in support from 1,000 lbs like # SSR-610-40 to 2,800 lbs like the # SSR-610-54. For a lighter duty application the lighter # SSR-610-40 would probably be better since you wouldn't lose as much ride quality.
Now with that said if you wanted the best in support, ride quality and stability the RAS system part # RAS4611TD is what you'd want. It will give you more support than you'd need (it's adjustable) and unlike other options... view full answer...
The only fifth wheel rail kit we offer that has been confirmed to fit your 2000 Toyota Tundra is the Husky Fifth Wheel Install Kit part # HT31563-686. These rails will fit with a Reese fifth wheel hitch like the part # RP30051. view full answer...
If you plan to install a brake controller in your 2008 Toyota Tundra that has a 4-way in it you would want the part # ETBC7. The # 37185 is just the 7-way that comes with the # ETBC7.
With the # ETBC7 you get circuit breakers, wiring, and a circuit tester. This would be everything you would need. With the # 37185 you would have to piece together the rest of the kit.
I attached an install video plus installation instructions for you to check out as well.
For a brake controller I would... view full answer...
For the 8 foot long bed versions of the 2016 Toyota Tundra Curt recommends the fifth wheel rail kit # C16304-200 as the correct fit. The # C16468-204 fits the 6-1/2 foot long bed versions of the truck only. For a hitch the Curt A16 part # C16120 is a really great option. It has a jaw design that wraps tightly to the king pin of the trailer for a smooth ride and a head that pivots quite a bit to allow for easier connection/disconnection of the hitch. view full answer...
I did a little research and found that your 2015 Outdoor Wind River 250RDSW travel trailer has a gross weight capacity of 8,700 pounds. This would make the tongue weight 870 to 1,305 pounds. To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind the rear axle of the tow vehicle.
Based on the potential... view full answer...
The # RRRTS534 wouldn't be my first pick for roof rack components for your 2011 Toyota Tundra since it requires permanent modification to the roof of the truck.
Instead the part numbers # RRVA150B-2, # RRRLKVA, and # DK079 would be what I recommend since this is a custom fit rack that would fit your truck and not require permanent modification.
I attached an install video for this rack on a similar 2014 Tundra as well. view full answer...
In order to convert from hydraulic to electric over hydraulic brakes you'll simply need an electric over hydraulic brake actuator. The HydraStar Electric Over Hydraulic Actuator for Disc Brakes part # HBA16 is our most popular option and what I recommend using. Then you'll have to address the coupler. The coupler may have a place for a lockout pin but if not you can either weld it or replace it altogether. I have attached the options for replacement. The last thing you'll need is the Trailer... view full answer...
Yes, the K-Source # KS81300 Snap-On Tow Mirrors are confirmed to fit your 2014 Toyota Tundra CrewMax Platinum truck.
However, you might also consider the CIPA # CM11300 Tow Mirrors which are also a confirmed fit, but look a little wider.
If you perfer a complete replacement mirror that is telescoping, check out K-Source # KS70131-32T view full answer...
The measurement you're looking for is referred to as the drop. The # UF35-946403 Hitch has a drop of 2 inches, which wouldn't be sufficient for you.
Curt offers the # 13703 hitch that has a three inch drop, but Curt's warranty requires that a stabilizing strap like part # 18050 be used for non-trailer loads like bike racks or cargo carriers. Since most motorhomes and trailers don't have a good spot to attach the strap, I'd pass on that one.
Your best bet would be a hitch like the Draw-Tite... view full answer...
If you have the factory 7-way installed on your 2015 Toyota Tundra all you would need to install a Tekonsha brake controller would be the correct install harness, part # 3031-P.
The 2015 Tundra brake controller port location is located behind the towing toggle switch area. The plastic housing for this area will pop out and it will be right there.
For a brake controller I recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well... view full answer...
You will need to check your local DOT to determine if there are laws on carrying a bike rack on the front of your 2006 Toyota Tundra. You will need to consider that your headlights might be partially blocked which will make night time driving different and air flow to the radiator will be partially blocked so your truck might run a little hotter.
The Swagman XTC4 Bike Rack # S64665 would work as long as the weight of it and your bikes are not more than the tongue weight rating of your... view full answer...
The best type of rear suspension enhancement for your truck in terms of trying to maintain a level setup with the trailer connected is with an air bag system that will let you adjust the air pressure based on load. For your 2018 Toyota Tundra 4x4 I specifically recommend Firestone Ride-Rite Air Helper Springs # F2445.
These heavy-duty air bags include custom brackets made for your truck which eliminate the need for any drilling. The bags can be adjusted from 5 psi to 100 psi so when it's... view full answer...
So you may be able to use the over/under kit you were talking about to get the needed clearance (at least 3" of clearance from the top of the tire to your fender and at least 1" of clearance between the inside of the tire and your trailer's frame rail), but that depends on the size of your axle. If it is a round, 2-3/8" axle you can use the Over-Under Conversion Kit # K71-384-00. Sounds like you have a 4 on 4" bolt pattern, and if so you could then use the Kenda Karrier S-Trail ST145/R12... view full answer...
If you have less than 8" of clearance from the hitch pin hole of your 2017 Toyota Tundra, then you have thee choices.
For the Hollywood Racks Destination, part # HR4000, to be used, you can remove the spare tire.
Or, you can keep the spare tire on and use a hitch extender like the Curt Hitch Extender for 2" Hitch Receivers - 8" Long, part # C45791. It will give 8" of additional clearance, but it will reduce your tongue weight by 50%.
Finally, you can opt for another bike rack with a... view full answer...
Go To Results