Yes, the bolts are indeed both M12 x 1.25 bolts for both the hitches you mentioned, the Curt Trailer Hitch Receiver # C11265 and # C13149.
So you can use a thread tap for those M12 x 1.25 bolts and you'd be set. view full answer...
For the 2014-2016 Toyota Corolla, the # SR1010 is a confirmed fit. The front crossbar overhang adjustment number is 16, the rear crossbar is 14. The center of the front roof rack foot will sit 8 inches forward of the seam between the front and rear door. The center of the rear foot would be placed 24 inches rearward from the center of the foot for the front crossbar, as shown in the table I've provided for you. view full answer...
The Curt Class I hitch, part # C11227 uses an M12-1.25x30 bolt. The bolt is 12mm in diameter, the thread pitch is 1.25 (meaning the threads are 1.25mm apart) and 30mm long.
You'd need a M12-1.25 thread tap.
If you haven't tried scrubbing out the weldnuts, you might try that first. Our installers have found that a steel brush like the one included with the # DW00254 battery terminal cleaner works very well. Soak the threads with a penetrating lubricant and allow it to soak for awhile before... view full answer...
The Curt Class I Round tube Receiver Hitch # C11265 uses 4 M12-1.25 x 30mm hex bolts. These bolts come with the trailer hitch. I only recommend using the included hardware to install the # C11265 trailer hitch.
Typically any vehicle that has seen a winter will need the weld nuts cleaned before installing a trailer hitch. We recommend using a lubricant and a wire or nylon brush to clean the weld nuts. Several of our installers like to use the Deka Battery Post and Terminal Cleaner - Wire... view full answer...
The heater Application Guide at Kat's Heaters indicates that on the 2005 Toyota Corolla with transverse engine their engine block heater # KH11813 will install on the driver-side of the engine on the rear surface facing the driver. They term this location rear left, or RL. Please refer to the linked diagram. view full answer...
Like you said, there isn't a master key for the RockyMounts lock cores. In order to change out a lock core you will need access to the back of the lock. Then with a small flat blade screwdriver or a knife you can press down on the pin that holds the lock in the housing and then push it out of the front.
In the video I made, it is a Rhino-Rack part but the process is the same. view full answer...
The values for the torque specs on the Curt # C11265 and Draw-Tite # 24913 trailer hitches that fit your 2017 Toyota Corolla are correct. The manufacturers of hitch make the directions according to how their hitches fit and are precise in their torque settings; the difference is likely due to the fact that the Draw-Tite uses M12 X 1.25 X 35 CL8.8 hex bolts, which are slightly different than the M12-1.25 X 30mm bolt of the Curt.
I do recommend the Draw-Tite # 24913 due to the fact that... view full answer...
Yes, the lightweight Malone MicroSport Trailer part # MPG462G2 will work great with the towing setup you mentioned for your 2006 Toyota Corolla.
Only thing you'll need additionally is trailer wiring like part # 55542 and you'd be set. view full answer...
The brake controller install harness on your 2016 Toyota Tacoma can be hard to find but the part # 3031-P will fit it. If you check out the picture I attached you will see where a customer found the connectors in a Tacoma just like yours. view full answer...
I viewed the video (1:08 mark) about the SportRack 3 bike carrier # SR3152 that you referenced, and the cradles are actually pretty secure and will take a little force to move them around to the desired position.
So you won't need to worry about the cradles sliding while you are driving down the road.
This bike rack can carry 3 bikes and the weight capacity is 105 pounds.
If you will be transporting any woman's, child's or alternative frame bikes, an adapter like # SR0500 will be a... view full answer...
Base plate installation on any vehicle, including # 1188-1 for your 2012 Toyota Corolla, is a fairly involved process. You will have to take the front clip off to install the base plates. Regarding the difficulty Roadmaster has a standard statement in all base plate instructions stating:
"Installation of most mounting brackets requires moderate mechanical aptitude and skills. We strongly recommend professional installation by an experienced installer."
I have included a link to the installation... view full answer...
There is a little bit of drilling for you to install the Curt Trailer Hitch Receiver # C34UR on your 2023 Toyota Corolla, but this is the same case for all of the hitches that fit your vehicle.
If you check out the attached photo you'll see there are two 1" holes you'll drill into your frame for the installation. I'm also linking the installation video we shot of this hitch on a 2023 Corolla for your reference! view full answer...
I went out to the warehouse and found from the top of the mounting brackets to the bottom of the safety chain loops (which will be the lowest thing on the hitch) of the Curt # C11265 is about 7-5/8 inches.
If you check out the linked instructions or the linked installation video you can measure down about 7-5/8 inches from where the trailer hitch mounts on your frame to get the ground clearance on your 2005 Toyota Corolla. view full answer...
For your 2017 Toyota Corolla XLE, the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24913 will not interfere with that rear jack lift point. I confirmed with the manufacturer and the online owners manual for your vehicle on page 518 that this hitch will not interfere. I've attached a video of this installation for your convenience as well.
If you will be towing with this hitch receiver, I recommend the Sportframe Drawbar 2-1/8" Rise or 2-3/4" Drop 2000... view full answer...
The only available trailer hitch for a 2020 Toyota Corolla at this time is the Draw-Tite Sportframe Trailer Hitch Receiver part # 24983 which does indeed require drilling. That said, this is very minor and it's only one hole per side. If you need to install a trailer hitch this is unavoidable. view full answer...
It sounds like you're asking about the installation of a Curt hitch on your 2019 Toyota Corolla. I'll start by confirming for you that the Curt # C11265 hitch is a fit on your 2019 Toyota Corolla. This hitch installs without any drilling required, so it's likely something that you could complete on your own, with a few basic hand tools. I've linked an installation video of this hitch on a vehicle like yours for you to have a look at and follow along with if you'd like to do it yourself-... view full answer...
The bolts included with the hitch # 24913 are M12-1.25x30 mm. Most likely you have the correct hardware and the weld nuts just need further cleaning.
Cleaning weldnuts out on a vehicle in order to install a trailer hitch takes a lot of time and elbow grease. Basically the weldnuts may appear to be clean but getting all of the grime out can take longer than you might think. Make sure you are use a lubricant like WD-40 or PB Blaster.
Check out he video and FAQ article I attached to the... view full answer...
We can help you with this issue, which is actually pretty common on vehicles that have a few miles on them, such as your 2012 Toyota Corolla, and the bolts that came with the Draw-Tite Trailer Hitch # 24913 are the correct size.
What happens in older vehicles is that open weld nuts (bolt holes) will amass some corrosion in them which will make it seem as if the bolts don't fit, when really, the bolt holes just need to be cleaned. I have attached a link to a help article that goes over... view full answer...
If the wiring harness you purchased has a separate ground wire then you will need to attach it to a clean and corrosion free bare metal surface to provide a strong enough ground to complete the circuit. Even on plugs that have a ground built in, sometimes a separate ground wire is needed, like on # HM11140415 for example, because the regular ground is not sufficient for the extra load on the system. view full answer...
The Curt trailer wiring harness part # 55542 that you have does have instructions that say to ground a white wire yet the harness does not have a white wire to ground. That step is in there by mistake and you would be fine to ignore it. view full answer...
Go To Results