To figure out the parts needed to convert a triple axle trailer to new 8-on-6-1/2 hub/drums you'll start by identifying the bearings and seals used in the current setup. A new hub/drum has to use the same bearings and seals in order to fit on the current spindles. Please refer to the linked photo diagram that shows how bearing and seal numbers usually appear on these parts. Pull one hub so you can remove the bearings and seal and try to find the part numbers.
Most of our 8-on-6-1/2 hub/drums... view full answer...
We do have an 8 inch hitch extender for a 2 inch hitch that has less than 4-1/2 inches of depth from the center of the hitch pin hole rearward, from Curt:
- Curt Hitch Extender for 2" Hitch Receivers - 8" Long # C45791
This extender measures just 2 inches from the center of its rear hitch pin hole to the back of the extender, so it will allow you to have the needed 4-1/2 inches of clearance. I have added a link below to a video review for you to check out as well if you'd like to take a look. view full answer...
I contacted Thule as well as another third-party vender and they both informed be that they only carry the head cap as part of the Fit Kit for Thule Podium-Style Roof Rack Feet - 3114 # THKIT3114. view full answer...
I have a solution for you but the Thule Rapid Traverse foot # 7522249001 you've got mounts to the vehicle with vehicle specific fit kit pieces; it looks like the fit kit is damaged and there is not a fit kit for the 2003 Toyota Matrix since it has raised side rails. The good news is that you can continue to use the Thule Aero style bars you got but you will need different feet.
The feet that are compatible with your aero bars and your Matrix are the Evo Raised Rail Feet for Thule Crossbars... view full answer...
Yes. You can rebuild the # LC178652 (follow leg) and # LC178653 (lead leg) with part # LC146059 for the lead leg and part # LC146060 for the follow leg. view full answer...
Yes. Based off the serial number provided (thank you for the pictures) you've got a Lippert Diamond tube torsion axle, so you will want to use the Axle Riser Kit # LC270682 on your 2017 Jayco Hummingbird 17RK. This kit provides 3-1/2" of lift. view full answer...
We have 2 available options that would provide a roof rack on your 1998 Saab 900.
The SeaSucker roof rack, part # 298-SX6000B attaches to the roof using 6 vacuum cups that are similar to suction cups. I know what you might be thinking, Suction Cups, really? These aren't the suction cups like what you've seen before. Each of the six cups has a pull strength of 210 lbs per vacuum cup, for a total of 1260 lbs. In other works, it'd take 1260 lbs of evenly distributed force to pull those cups... view full answer...
The Tekonsha # 118273 7-way trailer connector uses the same jumper harness and relays that are used by the Curt # C56281 so you can simply leave those in place and install the 7-way and harness provided with the # 118273 and plug it into the factory connectors you described. That harness will provide the trailer lighting, a 12V feed and transmit the brake controller output from the connector under the dash, but you'll need to install a brake controller to actually actuate the trailer brakes.
For... view full answer...
You are correct with the part you will need in order to convert your Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar for Blue Ox Base Plates # RM-677 for use with your Roadmaster direct connect base plates, which are two of the swivel ears:
- Replacement Swivel Ear for Roadmaster Sterling or Nighthawk Tow Bar # RM-910661
Along with the ears, the only other thing you will need the pins, like you asked about, which are the Replacement Base Pins with Chains and Clips for Roadmaster... view full answer...
I have a solution for you to use your existing rails, but the Husky Custom Mounting Bracket Kit # HT32221 is designed for a 2013-2020 Ram 3500 and cannot be used with a 2017 Ford F-150. However, you can use the Reese Universal Mounting Brackets for 5th Wheel Trailer Hitches - 10 Bolt # RP58314 with your Husky rails since this is a universal mounting bracket kit; it will likely require drilling into the frame of the vehicle.
With that said, the best solution would be to use the Reese Quick-Install... view full answer...
The correct base rails for your Thule TracRac SR system to move to a 2021 GMC Sierra with 5-1/2 foot bed are the Base Rails for Thule TracRac SR Sliding Truck Bed Ladder Racks # TH21782; these are the base rails for the TracRac SR # TH43002XT-782 view full answer...
The configuration of the Malone MicroSport trailer you're seeking is available with the Malone MicroSport Trailer with J-Style Carriers for 4 Kayaks - 800 lbs # MPG462G2.
I've linked a review video of this trailer for you to check out. view full answer...
When it comes to wind screen fairings for your Thule aeroblade roof rack, I recommend The AirScreen XT # TH82WV for Thule Crossbars. The aerodynamic fairing will deflect air over your roof rack to reduce wind noise and drag. They're 44 inches long x 5-1/2 inch tall by 2 inches wide.
I will put a specs review video below. view full answer...
Yes, the Rear View Safety Backup Camera System item # RVS-778718N will fit your 2013 Dodge 1500 Tradesman. This is a universal backup camera that has 33 feet of cable. You will have no problems attaching it to your Dodge Ram. I have linked a review video. view full answer...
For the trailer connector to adapt your 4-pin on your 2012 Honda Pilot to a 7-pin plug, that is the Adapter 4-Pole to 7-Pole and 4-Pole # 37185. While this kit does require a bit of splicing at the rear of your vehicle, we do not have a simple plug-and play solution because a 7-pole harness requires some additional grounds. The entire installation is completed at the rear of your vehicle without having to route wiring under the hood. The installation also involves installing the no-drill... view full answer...
While we do have the parts you need, we do not carry half kits of the Thule system you are looking for. With that being said, you do need a entire two-bar kit. That includes the following:
- Thule SquareBar Evo Crossbars - Steel - 60" Long # TH712500
- Evo Clamp Feet - Qty 4 # TH710501
- Fit Kit for Evo Clamp Feet # TH145182
With these parts, you will be able to use a 2-bar system or the single crossbar that you are looking for. It is important to note that this setup only works with... view full answer...
I took a look at what we got, and it doesn't appear that we stock any of the older Fulton jack parts, however I do have another suggestion.
I know you prefer to use what is already there, however since you're wanting to bolt on a wheel, I recommend upgrading the entire unit.
I suggest going with the Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind # TJDA-5000S which will easily bolt onto your trailer, has a lift capacity of 3,000lbs, and has a total lift of 28-3/4".
If you wanted... view full answer...
Most X3 models were equipped with the roof rails, so I initially thought you might be out of luck, but after searching around I found that Yakima offers a JetStream roof rack that would work perfectly on the bare roof of your 2013 BMW X3.
To assemble the rack, you'll need the following parts:
• 50 Inch JetStream crossbars in black as # Y00425
• BaseLine Tower Feet, part # Y28TR
• Front Fit Clip # Y06123
• Rear Fit Clip # Y06127 view full answer...
For your 2005 Keystone Montana, you have a couple of options to get your trailer level for towing.
Apart from adjusting the height on the hitch itself, you can also adjust the height on the pin box itself. You can make your height adjustment, by utilizing the different mounting holes, to pivot your nose up or down.
Finally, you can use an over-under conversion kit like # K71-384-00 for a 2-3/8" axle, or # K71-385-00 for a 3" axle. This will move your axle from above the leaf springs... view full answer...
There certainly is! For your Class A motorhome on the 2007 Workhorse W16 chassis, you'd need the # RM-RBK8-RSSA Reflex Steering Stabilizer. I've confirmed the fit with my contact at Roadmaster. view full answer...
Go To Results