The K-Source Custom Side Towing Mirrors w/ Lane Change Alert-Cam - Electric/Heat - Driver/Passenger Side # KSVS55010 has all of your features except the power retraction. They have the ability to be manually folded and retracted but they do not have that powered feature. They will connect directly to your current wiring without issue but you won't have that power retraction feature.
There is not a towing mirror that has that powered folding feature from any of the manufacturers we work... view full answer...
The TorkLift GlowStep Revolution Scissor Steps with Landing Gear # TLA8004 weighs 55 lbs. These particular steps fit an entry height of 32-1/2" to 44" and the steps themselves are 22" wide x 8" deep to ensure plenty of footing.
They can even be locked with the Pin Lock for TorkLift GlowStep Scissor Steps # TLA7509 and if you'd like, for added stability when traversing the steps you can add a handrail, the TorkLift GlowGuide Handrail # TLA7621.
I have added a link below to a video review... view full answer...
Tekonsha gives a installation time of 30 minutes for the T-One Vehicle Wiring Harness # TK69FR on your 2021 Toyota Sienna. This is typically a time given for an experienced technician who has experience with the vehicle and its components.
As we have not had a 2021 Sienna in our shop to install this part on ourselves currently we have not included our rating on this product yet. I would think that this would be a roughly 1 hour installation depending on your mechanical ability and knowledge... view full answer...
The Rhino Rack # Y01-140B-NT includes the crossbars, the roof rack feet and the hardware necessary to mount the feet into the existing Thule or Yakima-compatible rails in the channel on your Leer camper shell. Everything shown in the photos I provided is included. view full answer...
According to my research, your best bet would be to use a Tow Dolly like # RM-2050-1, but ONLY if your Vibe is equipped with the U341E automatic transmission, it can be towed if a transmission lube pump is installed. We don't offer the lube pumps, you'd need to locate a part # LP-BK01-019 lube pump kit online.
If you decide to go that route, you'd need base plates, a tow bar, safety cables, a wiring harness, a supplemental braking system and possibly a high/low adapter to successfully... view full answer...
A trailer jack only needs to support the tongue weight, which for a boat trailer is something like 5 to maybe 10 percent of the weight of your loaded trailer, because so much of the weight is at the rear of the trailer. To be absolutely sure you will need to know your tongue weight by using a scale like the etrailer Tongue Weight Scale # e99044 but we can make a good guesstimate.
With a 3,100 lb boat, since the trailers themselves are usually fairly light you can get away with a 2,500... view full answer...
Sometimes it's hard to find the wiring as they are sometimes taped up and out of the way. I've included a picture of the instructions to help you find the right spot. The connector should be on the back side of the vehicle harness. That's probably why you aren't seeing it. I've found that they are pretty neatly tucked behind the wires so it takes some looking to find it. When you do find it, you can use this adapter # C51455 for your brake controller. view full answer...
The Pop-Up Camper Latch and Catch, # 37211845 has an adjustment range of about 1/2". From the bottom fastener holes on the main body of latch assembly to the fastener holes of the catch, is approximately 5-1/4". view full answer...
The etrailer brand # e98854 Class III hitch would install using hardware that is already existing on the vehicle, so no separate hardware is needed. You can see this by consulting the linked installation instructions or taking a look at the linked install video. view full answer...
The video you saw on Curt's website about the dividing tongue weight with distance in feet of the carrier is referring to the weight of your receiver. So if you had the etrailer Receiver # e98847 on your 2016 Subaru Outback with a tongue weight rating of 600lbs, then Curt would recommend not exceeding 300lbs of weight including the 64lbs of the 24x60 Curt Cargo Carrier # C18152. Or a total gear capacity of 236lbs. view full answer...
You can absolutely continue using your existing wheels if you upgrade to a higher load range tires. As long as you don't exceed the 910 lb per tire/1820 lb per axle capacity of the wheels, you'll be just fine.
If you wanted to use the # AM30155 as a spare tire, that would work fine. You want to run tires that all have the same load range, but if you use the Load Range D tire as a temporary spare only until you can get the load range C tire repaired or replaced you'll be just fine. view full answer...
The fact that the Curt # C51170 has a direct connection to battery is not unique to the Curt Spectrum brake controller, they all install in that manner. This is purposely done as a safety measure, so the user can't forget to turn on the brake controller before they tow.
The good news is that after a short period of inactivity (varies from 10-20 minutes) the controller will go into a sleep mode, at which point they only draw a miniscule amount of power. Unless the vehicle will be left unattended... view full answer...
The B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200 should not be drilled into. The coupler sleeve is required to either have 2 set bolts or 1 set bolt if you have a safety through pin to secure it in place on your tube sleeve.
A Master Lock Laminated Steel Padlock # ML1KA can be used to secure the coupler when attached to your tow vehicle. And if you choose to have multiple locks keyed alike you can use them all to secure any locks on trailer as well to have a one key system of locks. view full answer...
The Gustafson vanity lamp you referred to, part # 277-000429 operates on 12V DC power. The LED lamp offers bright light, long life and a minimal power draw.
At this time we do not carry any 120v lights, as it is pretty uncommon for a trailer to use 120v lighting. view full answer...
The batteries should indeed be grounded to the trailer frame. A battery disconnect switch like # 277-000096 would install inline on the positive circuit of the battery as shown in the video I've linked for you. view full answer...
The TorkLift Custom Frame-Mounted Camper Tie-Downs Front # TL44FR is the TorkLift part number C2226. The Rear # TL84FR is the TorkLift part number C3222. These are the correct parts for your 2023 Chevrolet Silverado 3500 Long Bed Dually with the factory receiver and no steps/running boards under the bed.
I recommend using the TorkLift Locking FastGun Turnbuckles # TLS9529-2-LK to secure your slide in camper on your Silverado. These have a stainless steel construction with black powder... view full answer...
I went out to our warehouse and measured/test fit the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover # FVU1500WH and Fan-Tastic Vent Roof Vent # FV807350. When the lid on the # FV807350 is fully open it sits approximately 11" from the mounting flange. The # FVU1500WH only has 10" of interior height.
The manufacturer, Dometic, knows this and says that it should sense the lid pressing against it and stop to prevent damage to the gears. There is not another cover with a larger interior... view full answer...
The issue is definitely that you have an underrated system, which is why you are experiencing sway. The Equal-i-zer Weight Distribution System # EQ37060ET you said you have now is rated for total tongue weights - the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your truck - of between 200 lbs and 600 lbs, with the ideal system being one in which your total tongue weight is in the middle of the system's rating.
For a trailer... view full answer...
Go To Results