I know it reads a bit confusing Justin, but the Rampage Trail Top All-Season 2-in-1 Soft Top Kit for Jeep # RA106035 does come with the door surrounds, windshield bar, tailgate bar, and support bows. view full answer...
Hey Mark,
We can get you the breakaway kit for your Blue Ox Patriot supplemental braking system for you to use on your Jeep, and all you need is the following:
- Second Vehicle Breakaway Kit for Blue Ox Patriot Flat Tow Brake Systems # BRK2505
I'm not 100% clear on what you need when you say the wiring harness for plug to your motorhome in regards to the Patriot system. Did you mean something like the replacement controller that plugs into your motorhome? Or were you referring to wiring... view full answer...
Hello Charles,
Correct, there are no supports directly under the mesh bottom of the Curt Cargo Carrier for 1-1/4" and 2" Hitches # C18110.
The # C18110 has braces at the front and back that extend out (see photo) so the entire weight isn't supported only by the middle beam, but nothing directly under the mesh.
If you want something that does have supports directly under the floor of the carrier you'd need one from Reese, with the correct option depending on your hitch size. Either the... view full answer...
Hey Jeff,
I doublechecked the Curt Trailer Hitch Receiver # C13392 and # 13432 as they are labeled with their capacities and also reached out to Curt for confirmation. After speaking with Curt we found that their website incorrectly listed the capacities lower than they actually are. They should be fixing this issue and we'll have it properly labeled on our site as well and updated in our answer pages to avoid further confusion.
The # C13392 is rated for 500lbs TW / 5,000lbs GTW
The... view full answer...
For your 2021 Jeep Wrangler Unlimited, you can use either the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM39VR you mentioned, rather than the Roadmaster Wiring Kit with Smart Diodes # RM47ZR. If you choose not to use # RM47ZR and you use # BLU79FR you will not need any additional wiring as this is a plugs into your vehicle's harness.
If you choose to use # RM47ZR, then you may need the Roadmaster Brake-Lite Relay Kit # RM-88400 if you use this kit with a supplemental braking... view full answer...
Hello Willie. The etrailer Spare Tire Mount does not have a designated weight capacity, and it is designed to work with heavier tire/wheel combos. Basically, it can handle the weight of any tire/wheel that will fit. It will fit any wheel with 6 lugs or less. So, as long as your wheels fit that criteria, it will work great, regardless of tire size or weight. view full answer...
The only way to get a new pin for the Bolt-On Zinc Spring Latch # SL716 is to completely replace it. I'm sorry to say the pin itself is not available as a replacement part. view full answer...
Hi Ken; the Rhino-Rack Pioneer Platform Rack with Backbone Mounting System # JB0892 fits the 2018 Jeep JL Wrangler Unlimited hard top as well as the 2024 Wrangler Unlimited hard top so you will be able to carry it over to your Rubicon X. I have attached a link below to our list of local dealers in the Nashville area that could install the rack for you. I used 37201 as the zip but you can change it as needed. view full answer...
Hey Jason, it sounds like you are maybe asking if the Curt trailer wiring harness part # 56407 could possibly power the taillights of your vehicle due to a parasitic draw you are experiencing? If so, this could do that but it wasn't intended to do so.
If instead you were asking if this can be used for trailer wiring without draining the battery of the car it is installed in the answer to that is yes. It would not drain the battery if left installed. view full answer...
You should get a constant 12 volts on the red wire when you step on the brakes and no voltage when not stepping on the brakes. You can use a circuit tester like the item # PTW2992 to measure the voltage coming off of the 3rd brake light. For your 2016 Jeep Wrangler Unlimited, I recommend tying into the white and brown wire coming off of the brake light switch. view full answer...
Hey Charles, thanks for reaching out!
I'd be more than happy to help answer any questions you have about the Yakima BackSwing # Y02483 and the HoldUp # Y02443 or HoldUp EVO # Y02479 bike racks.
Let me know what you're wondering and I'll help you look into them. view full answer...
Hey Patrick, so I took a peek and what we have for you and I was able to find the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles # HM39VR which is a custom fitting harness that plugs into your existing wiring without splicing.
As far as the Roadmaster Stop Light Switch Kit # RM-751490 goes, you are going to need that with your Roadmaster Even Brake Portable Flat Tow Brake System # RM-9400 to complete install. You're also going to need the 12 Volt Outlet Kit, 20 amps # RM-9332. view full answer...
The Lippert # LC281255 will only work with round axles. For square axles I recommend the SumoSprings Trailer Helper Springs which mount on the leaf spring stack. If you have overslung axles (leaf springs on top of axle) you need # TSS-107-40 and for underslung # TSS-106-40. These will absorb road shock while also reducing sway and body roll. view full answer...
Unfortunately Jamie, the Rhino-Rack Cargo Box # RR67AP can only be mounted onto a platform rack. Since you are wanting to use a pair of the Rhino-Rack Crossbars # RR86ZE you would want to consider a cargo box like the Thule Pulse # TH613 view full answer...
Unfortunately Lucas, that is the limitation to the Blue Ox Patriot Portable Flat Tow Brake System # BLU37TR. This is why I always recommend going with either the Demco Stay-iN-Play # SM99251 or Air Force One # SM99243 braking systems as they actually tie into vacuum brake boosters to give the additional brake pressure. I will say I am not surprised the braking system on your Jeep is not slowing the tow vehicle pulling it as Jeeps are very light and with very light towing capacities they... view full answer...
The Demco Stay-IN-Play Duo Braking System # DM86VR is a standalone system so no brake controller is required. The same is true for our other supplemental braking systems for flat towing. The Stay-IN-Play senses the rate of your RV's deceleration and triggers your towed car's brakes to slow down at the same rate just like a proportional brake controller. The Curt Spectrum # C51170 is only designed to work with trailer brakes. view full answer...
Hey Chad, so we really cannot recommend using the Curt # C96JR (58964) with the Roadmaster Invisibrake # RM-8700. Like you said, the Invisibrake requires diodes in order for the unit to function properly. Instead, I recommend using Roadmaster Diode Kit # RM-15267, which will contain the necessary diodes.
Keep in mind that if your Jeep is equipped with the ParkSense feature, you will need to use the Smart Diode Kit # RM63MR along with two additional diodes # RO54FR. view full answer...
Hi Brad,
There isn't going to be anything really different when installing the second vehicle kit # RM-98700 in your 2024 Jeep Wrangler. The Roadmaster Wiring Kit # RM47ZR is most likely going to be the only difference between this Wrangler and the previous towed vehicle, but even then it's still the same concept for installation. This won't come with a 6-pole socket # RM-910030-7 so if you didn't pull the one off the other vehicle you'll want to pick up another to complete the installation.... view full answer...
For light trailers like your 2,500lb popup I recommend the Fastway e2 4,500lb Weight Distribution Hitch # FA92-00-0450. This hitch is rated for trailers up to 4,500lbs with a maximum tongue weight of 450lbs. You will need either a 2" # 40038 or 2-5/16" # C40005 ball depending on your camper.
If you feel like you might go up in camper size in the future the Fastway e2 6,000lb # FA92-00-0600 may be a better option. This is rated for trailers up to 6,0000lbs with a tongue weight of 250-600lbs... view full answer...
Hello Peter. I ran all of this by my contact at Roadmaster. I was informed that you will need the RoadMaster BrakeMaster Custom Seat Adapter # RM87VR instead. This will have more of an offset to the inside of the Jeep. I will have customer service get in touch with you to initiate a return and help get the correct part in your hands. view full answer...
Go To Results