The 4-way wiring harness does not come as standard with a 2022 Hyundai Tucson so you'd need to add one to go with the trailer hitch. It's really simple though as all you have to do is plug the harness in. The correct fits for your '22 Tucson are the following:
- Draw-Tite Max-Frame Trailer Hitch Receiver # DT22MR
- Vehicle Wiring Harness # CU94FR
There will be a plug under your Tucson, behind the bumper on the driver's side (it may be behind a removable plastic panel). All you will do... view full answer...
Yes, the Inno Aero Crossbars item # INXB108-115 are compatible with the Rhino Rack 2-Kayak Carrier item # S512-S512X. This carrier includes tie down straps to secure the kayaks to the carrier and bow/stern tie downs as well.
I recommend some anchor straps, like item # RRRBAS-2 to provide a convenient place to secure the bow/stern tie downs on your Hyundai Tucson. view full answer...
I'm fairly sure the Limited model of the 2015 Hyundai Tucson has factory raised rails on its roof. If so, there are three Malone roof rack options that fit; the 58 inch SteelTop square bars # MPG202, the 65 inch SteelTop square bars # MPG203, and the 58 inch AirFlow2 aero bars # MPG216. Between the three I recommend the AirFlow2 because of the aero bar design that reduces wind noise and has an overall better look, in my opinion.
If I'm wrong about your Hyundai's roof and you actually... view full answer...
The Inno Phantom 466 Rooftop Cargo Box # INBRM466WH will fit your 2013 Hyundai Tucson but it may have some contact with the antenna. If you have a naked roof then you need the Thule SquareBar Evo Crossbars # TH712400 with the Evo Clamp Feet # TH710501 and the Fit Kit # TH145134. This setup with the Phantom 466 # INBRM466WH may interfere with your antenna which is why I would recommend getting the SportRack Vista XL Cargo Box # SR7018 because it is a lot shorter but still can carry 18 cu... view full answer...
Welcome back! Since your 2022 Tucson already has a 4-way connector, you will want the Universal Installation Kit for Trailer Brake Controller item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your Hyundai with an included bracket. This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it.
You will then connect the blue wire to the blue wire on the brake controller, the black... view full answer...
We do have an option for a flush-mounted roof rack that fits your 2020 Hyundai Tucson with a naked roof, but I verified with Rola that there is not a fit for their rack on your '20 Tucson. What will fit instead is an option from Inno, which has the same flush-mounted style as the Rola for a streamlined look. The correct parts for your Tucson are the following:
- Inno Aero Crossbars # INXB108-115
- Inno Flush Feet for Aero Crossbars - Naked Roofs # INXS200
- Custom Fit Kit for Inno #... view full answer...
Both the # C94WR and the # e38KR will fit your 2022 Tucson Hybrid. The hitches are identical with the exception of the finish so I would let that be the deciding factor. The Curt has a glossy finish and the etrailer hitch has a matte black powder coat finish. Personally I prefer the matte black since that gives it an OEM look and does a better job hiding dirt and dings.
If you plan on towing, you will also want the # CU94FR for wiring. This will give you a 4-way to power your trailer's... view full answer...
Yes, we do have a trailer hitch and wiring that fits your 2024 Hyundai Tucson.
Hitch
- etrailer Trailer Hitch Receiver # e38KR
This hitch has a bolt-on, no-drill installation and will provide you with a 2" hitch receiver. The 2" receiver is the most common size used for hitch mounted accessories. It also has a nice matte black finish that I think looks better on your vehicle once installed.
Wiring
- Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236
If you... view full answer...
I just confirmed with Draw-Tite that the Draw-Tite Max-Frame Trailer Hitch Receiver item # DT22MR does fit the PHEV model of the 2022 Hyundai Tucson. If you'll be using the hitch for towing, you'll also need a trailer wiring harness like the Curt item # CU94FR. You will also want the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver... view full answer...
The Curt # C12241 is rated to tow up to 3500-lbs, but when towing you're always going to be limited to the lowest rated component in your towing setup. From what I'm able to tell by researching, the 2018 Hyundai Tucson only has a towing capacity of 1000-lbs, so I can't advise you that this would be safe for your vehicle.
I do recommend confirming this capacity in your vehicle's owner's manual and following the directions there; if it says that your towing capacity is 3500-lbs then you... view full answer...
According to Curt Manufacturing, the Class III Receiver, part # C13120 is a fit for your 2012. The Tow Ready T-One Vehicle Wiring Harness, # 118501, will also fit the 2012 Hyundai Tucson. I have attached installation videos for the hitch and the wiring harness on a 2012 Tucson for you to check out.
In addition to the receiver hitch and wiring harness, you might also need the following:
Ball Mount, part # D-4
Hitch Pin and Clip, # PC3
1-7/8 Inch Trailer Ball, part # 19260
2 Inch Trailer... view full answer...
We talked with our contact at Thule this is what they told us about your Tucson with the glass roof:
The trim pieces that surround the glass roof do not allow the pad to sit properly in the ditch. The trim pieces are also not a structural load bearing section of the roof and the pad would apply too much pressure on this area during installation and further so under load. The fits by the other manufacturers likely sit outside of the ditch area which allows them to fit the glass roof models.
A... view full answer...
We don't make one, but Curt does!
For a 2020 Hyundai Tucson, you'd need the Curt 14385 Class III hitch which we offer as part # C94WR. If you'll be towing with the hitch, you'll also need a trailer wiring harness like part # CU94FR, a ball mount like part # 2753 and a trailer ball like # 19260 for a 1-7/8 or # 63845 for a 2 inch.
I've linked to an install video for the wiring harness, as well as to an installation instructions for both the hitch and the wiring harness. view full answer...
The hitches designed for the 2012 Hyundai Santa Fe and the 2016 Hyundai Tucson are completely different, so the hitch from your Santa Fe won't work on the Tucson, I'm sorry to say.
For the Tucson, I'd recommend the Draw-Tite Class III hitch, part # 75836. If you'll be using the hitch for towing purposes, you'll need a few other items to complete your towing system:
Trailer wiring harness, part # 118501
Ball mount, part # D-4
Hitch Pin and Clip, # PC3
1-7/8 inch trailer ball # 19260 or... view full answer...
Yes, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat # CU94FR is the correct wiring kit for your 2023 Hyundai Tucson Hybrid. view full answer...
To use your Roadmaster StowMaster # RM-501 on your 2010 Hyundai Tucson you will need to find a Roadmaster base plate kit 1628-1 as we no longer carry this. If you are unable to find this I recommend using the Demco Base Plate # DM9518277 with our etrailer SD Non-Binding Tow Bar # e34ZR.
You will need a Wiring Kit # RM-15267 if you do not already have Magnetic Tow Lights # TLL21RK you use with your other vehicle. A braking system like the Brake Buddy Select 3 Portable Supplemental Braking... view full answer...
The Curt Trailer Hitch Receiver # C94WR for your 2023 Hyundai Tucson will only have the 5/8" holes for a hitch pin and clip. Curt does not offer a receiver with the type of anti-rattle hitch lock you described. We do have the Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin # SR25219 which will allow you to have a similar style lock for hollow tube hitch accessories. view full answer...
The etrailer Trailer Hitch Receiver part # e38KR is a confirmed fit for a 2023 Hyundai Tucson Hybrid. In fact, the video I have attached for you below is on a Hybrid. This is an excellent trailer hitch option with bolt-on install, hidden design, and class III rating for use with all your favorite accessories from bike racks and cargo carriers to ball mounts.
If you plan to tow a trailer, you will need a wiring harness as well. I recommend the Curt T-Connector # C68JR (for vehicles with... view full answer...
We have a special rack that is specifically designed for heavy electric bikes. I recommend the Hollywood Racks Sport Rider for electric bikes # HLY84FR. This rack has a capacity of 80 pounds per bike.
Since you have a step thru frame you may need to use an adapter bar like part # UB01 so the hook can secure your bike. view full answer...
Go To Results