Yes, the rear hatch of your 2014 GMC Yukon XL can be open or closed with the Rightline Gear SUV Tent with Rainfly # RL110907 installed on it. view full answer...
There are no modifications required whatsoever to your 2022 GMC Yukon XL's wiring, and you can absolutely use the Curt wireless brake controller, which is the following part number:
- Curt Echo Wireless Trailer Brake Controller # C51180
This will just plug directly into your Yukon's 7-way and you'll have a functioning brake controller. As far as power to the electric brake pin, there is on your Yukon, but that is not actually needed with the Echo # C51180; all that is needed for this... view full answer...
The K Source Custom Towing Mirrors, # KSVS55010, for your 2014 GMC Yukon Denali XL have a black finish that is ready to be painted to match the vehicle. A chrome set is not available. They do not power fold in but they do have power electric mirror face operation, heat, and turn signal functions as well as the Lane Change Alert-Cam. Please note that you cannot upgrade to power remote operation, heated mirror face, and turn signal or Lane Change Alert if your factory mirror is not already... view full answer...
The main grille insert, # P84159, does not require removing the bumper but you will need to remove the factory plastic hood that covers the area between the grille and radiator so you can get your hands behind the grille to complete the installation. This is the normal installation procedure and should be much easier than removing the front end of the vehicle.
The lower grille, # P84160, uses self-tapping screws to install so you should not have to get behind it at all. view full answer...
On your 2008 GMC Yukon XL, there is not a direct plug and play harness for a brake controller. This is because no plug is present under the dash, however the needed wires are already run so it is a simple install. You will connect the brake controller wiring with the vehicle wiring already present under the dash with butt connectors like # 05731-5.
The Curt Discovery Timed Delay Brake Controller # C84VV gives you the option to either cut the connector off the brake controller or use... view full answer...
On your 2014 GMC Yukon XL there are two wires under the hood that have to be connected to make the tow package functional, one is the power wire to the brake control and the other is the battery charge line to the 7 way connector. This is the wire that feeds the 7-way circuit on the pin at the 1-o-clock position as you view the socket.
These wires are both Red/Black with eyelets on them. They are coiled up under the hood and will need to be connected to the under hood fuse box. One of... view full answer...
Yes, you will need to connect two wires under the hood of your 2011 GMC Yukon XL to wire a brake controller to your vehicles brake controller circuitry. To attach those wires to your vehicle you will need a Zinc Plated Hex Flange Nut - M6, part # 185916, and a Zinc Plated Hex Flange Nut, part # 185917.
I attached an FAQ article on how this is done below for you to check out, as well as the video that you watched of the brake controller being installed on a 2011 Chevy Silverado that you... view full answer...
The installation procedure for the GM full size trucks would be identical to the procedure you will use to install a brake controller in your 2009 Chevy Suburban. The tow package wiring is located under the dash, to the left of the steering column. The blue tow package wire connects to the blue wire on your Prodigy, the blue and white tow package wire connects to the red wire on the Prodigy, the red tow package wire connects to the black wire on the brake controller, and the white ground... view full answer...
You are going to have to pull out the third row seats in your 2016 GMC Yukon XL and then place the mat # WT440665 over that area and then reinstall the seats on top of it. view full answer...
On the 2014 GMC Yukon XL there is no plug under the dash to plug in a brake controller adapter for your Tekonsha Primus, part # TK90160, but there is a tow package wire bundle under the dash just to the left of the steering column. It will have a white tag attached.
I have attached a link to an installation video for a brake controller on a 2013 Yukon you can check out. The installation will be the same on your 2014 Yukon. You can also check out the helpful article I have attached that... view full answer...
So the Firestone kit you mentioned for your 2005 GMC Yukon XL 2500 has been discontinued for quite some time, which is why there is no way to piece together its contents.
The only air springs that fit your '05 Yukon XL are the Air Lift Ride Control Air Helper Springs # AL59526, and like you said, they do mount on the leaf spring itself as opposed to the axle, like you see in the accompanying cut out of the linked directions. I know you mentioned you didn't like this aspect of the kit,... view full answer...
Yes, you can technically install the Derale 9" Tornado Electric Fan # D16509 in front of the transmission cooler of your 2011 GMC Yukon XL but it may be that you are getting diminishing returns. This fan is unique in that it can be used as a pusher or puller application so I recommend instead that you install this fan behind the radiator which is going to maximize your cooling efficiency. view full answer...
The port for installing the brake controller is located in a junction box behind the emergency brake pedal. Remove the black lid from the junction box, the brake control adapter is plugged into the second slot from the left on the top row. If you need the adapter harness and you're using a Tekonsha brake controller, we offer them as part # 3025-P. If your controller doesn't have a socket on the back just wires exiting the rear, cut the black connector off the harness and wire it to the... view full answer...
Different manufacturers sometimes have different philosophies about the set-up process of a weight distribution system on a vehicle with factory air shocks. I can share with you the process we have found to work well for us when setting up a weight distribution system in this situation.
First, with the vehicle and trailer level, take the measurements of the vehicle hitch receiver height and the trailer coupler height. You will want to take these measurements while the vehicle and trailer... view full answer...
To install a brake controller in your 2003 Monaco Windsor built on a Roadmaster chassis you will need to hardwire it. I attached an FAQ on how this would be done. Basically you will need to run the blue wire from the controller back to your 6-way. The black wire will run to the positive post of your MH battery through a 20 amp circuit breaker like part # PK54220. The ground wire will run to the negative side of your battery.
The red wire will need to be run to the fuse control center,... view full answer...
Once the E-Track Wood Beam Socket for Standard 2" Lumber - Qty 1 # 59149 has a beam screwed in at both ends, it cannot be removed without unscrewing the wood beam. The beam would need to be lifted straight up and out of the hanger to allow movement and then be screwed back in place in its new location.
You will be able to use the same piece of lumber cut to width over and over again, but it will need to be removed to change location of the hangers in the track. view full answer...
You have stumbled upon one of the great brake controller conundrums that is often overlooked; and that is where to mount the brake controller. There is no definitive answer but there are some criteria that you should follow that will help you choose the best location.
You will want the controller within easy reach of the driver and in a place where it will not obscure the drivers view of the road. It will also need to be mounted within the ranges specified in the instructions (linked... view full answer...
The Westin Sportsman Grille Guard - Polished Stainless Steel # 45-2130 will fit your 2007 GMC Yukon Denali XL 1500. There is not a different unit for the Denali trim package according to my tech contact at Westin. The trimming of tow hook area may or may not be needed depending on your specific vehicle as some of the bumpers are more closely formed around the tow hooks than others. Trimming would only be required if the bracket needs more room to fit and the best way to trim is using... view full answer...
There is not a vehicle specific installation kit available for the Flex-a-lite Flex-Wave Electric Fan # FLX236 but it does install by mounting directly to your radiator core using nylon bolts and push nuts. This will be a great solution for your 2003 GMC Yukon XL when towing your camper and will work to keep you from overheating, especially if you tow a lot in areas with restricted air flow or at low speeds.
If you want to have your fan turn off when the air conditioner is going you'll... view full answer...
At this time there is no plug under the dash of your Yukon. This means installing the Prodigy P3, part 90195 will need to be hardwired to the wiring under your dash. I have attached a link to an installation video for a brake controller on a 2013 Yukon you can check out.
If you have no factory trailer connector you will need part # 30955 to finish the wiring. view full answer...
Go To Results