The DeeZee Specialty Series Trailer Tongue Tool Box part # DZ91717P comes with the box and mounting hardware needed to attach it directly to the top of the frame rails. It does not include a metal base nor is this needed. I have attached a video for you of a sample installation you can use but please keep in mind not every trailer is the same so yours may require some modifications such as adding support or cross bracing etc. view full answer...
The RC Manufacturing T-Series Trailer Tongue Toolbox - A-Frame - Steel # 313-TM362016M is just the steel box. Most people drill into the bottom of the box to hold the box to the trailer frame with self-tapping screws like # WLS100.
You can weld it if desired, but that is not how most choose to attach the box to their trailer frame. view full answer...
The DeeZee Specialty Series ATV Toolbox # DZM207 does not require support under the tool box to carry cargo. If you wanted to attach the back wall of the toolbox to the side of your car trailer you could easily carry 50-75 lbs of cargo.
You would want to brace the wall of the trailer as well as the install brackets used in the tool box. view full answer...
The DeeZee Trailer Tongue Tool Box does not feature pre drilled holes, but the included sheet metal screws can be used to secure the box to the trailer tongue. The instructions call for 3/16 inch holes to be drilled through the bottom of the box into the trailer frame. Make sure you avoid any wires that might be running along the trailer frame. You can see the installation instructions by clicking the provided link. You could use u-bolts if you wish. view full answer...
For your 2012 Ford F-Series Super Duty with a long bed we have a tonneau cover that is specifically designed for fitting behind a tool box with the Access Toolbox Edition Cover part # 834532008460 which will fit and work well as long as your tool box width is between 19 and 21 inches in width. The Truxedo you referenced only fits the short bed versions of your truck so I can not recommend it for your long bed truck. view full answer...
You can use the Rola Haul-Your-Might T3 Truck Bed Ladder Rack - Aluminum - 800 lbs item # 59799 with both your truck tool boxes on your 2014 Toyota Tacoma. It will not interfere with your side tool box. You will have to mount your truck box either in front of the ladder rack or behind it. You can not mount your truck box on top of the front legs. view full answer...
You'll want have your load centered from side to side on the trailer, as well as front to back. Centering the motorcycles should alleviate the concern of your tool boxes as they are at the front.
Centering from front to back could also change the tongue weight and you are going to want the tongue weight to be 10 to 15 percent of the gross trailer weight. The etrailer Trailer Tongue Weight Scale # e99044 is perfect for getting that number exactly right. Having a balanced trailer helps... view full answer...
The chain lift brackets in the Reese Strait-Line Weight Distribution System # RP66084 mount to your trailer frame about 30-inches back from hitch ball and the brackets themselves measure approximately 5-1/2-inches wide.
If your trailer frame does not have enough available space to mount these supplied brackets you can instead use Reese part # RP58305 which bolts on to the side of your trailer frame using included hardware (2 bolt lengths are supplied to enable a good fit on various frame... view full answer...
To be blunt you should definitely not alter the installation in any way of the Turnoverball Install Rails # BWGNRK1016-5W or the B&W Companion # BWRVK3400-5W, or the Companion # BWRVK3770 if you have the OEM pucks in your 2019 GMC Sierra 2500 with a 6-1/2 foot bed.
There may be one option for you since you mentioned 18 inches wide and that is the UWS Truck Bed Toolbox - 5th Wheel Series Chest # UWS01042 (Bright Aluminum) or # UWS01066 (Gloss Black). This box measures 58" long x 18" wide... view full answer...
As long as your fuel tank/tool box sits lower than the top of your bed rails the TruXedo Deuce 2 Soft Tonneau Cover # TX771601 would fit over it without any interference.
This cover sits on top of the bed rails and would allow a box to fit underneath it as long as the box wasn't taller than the rails.. view full answer...
Yes, I spoke with my contact at Thule and they informed me that the Thule TracRac Side-Mount Truck Bed Ladder Rack # TH14750 that you referenced could be installed in the bed of your truck that has a tool box currently installed in it. You would just have to install the rack directly behind the tool box. view full answer...
On the output post of your dual alternators you will need to run a thick gauge wire from there to the positive post of the batteries you plan on installing in the tool box of your truck. This will put a decent charge on those batteries while you are driving.
To prevent the batteries from discharging your truck batteries you will also need to install the # PK5231201 isolator on this charge line. This will prevent the circuit from the battery of your truck to the battery in your tool box... view full answer...
The B&W Companion # BWRVK3500 is a fixed hitch and for your 2009 Chevrolet 2500 with a 6-1/2 foot bed you're going to need a sliding hitch to have enough turning clearance.
The sliding Companion is # BWRVK3400-5W which will give you an 12 inches of travel to help you make sharp turns. To determine if this will be enough for you to make sharp turns you can do a little math. You need to take the distance from the center of the hitch's jaw to the cab of your truck and add the 12 inches... view full answer...
The Weather Guard Truck Tool Box part # WG45EV is designed to mount in front of the wheel well on the driver side of the truck bed. view full answer...
Since the UWS Underbody Toolbox - Single Door - 6.8 cu ft # UWS04010 can be mounted in a variety of ways there is no specific mounting kit for it. I reached out to my contact at UWS and he said that they recommend visiting your local outfitter so that box/bracket can be installed to the frame of your vehicle. Then you need to secure this tool box to the box/bracket with at least 1/4" steel.
This tool box has dimensions of 36" long x 18" wide x 18" high (see attached). view full answer...
I do have a truck bed tool box designed to work with the BAKFlip MX4 Hard Tonneau Cover part # BAK48120 for your 2017 GMC Sierra 1500 but the TruXedo TonneauMate Truck Bed Toolbox part # TX1117416 will not work as it is only designed to be used with TruXedo tonneau covers not BAKFlip tonneau covers.
For a toolbox that is confirmed to work with your BAKFlip MX4 Hard Tonneau Cover, I recommend the BAKBox 2 Collapsible Truck Bed Toolbox part # BAK92120. This toolbox is 10" wide x 10" deep... view full answer...
The tools that you will need to install this Curt Trailer Hitch Receiver with Drawbar, part # 11771, are:
Ratchet
10mm socket
18mm socket
3/4 inch socket
5/16 inch open end/box wrench
5/8 inch open end/box wrench
11/16 open end/box wrench
18mm open end/box wrench
small disk grinder
torque wrench
For the best possible access you will want to have your vehicle lifted with either a car-lift or a jack. If you use a jack make sure to secure the vehicle with jack stands. As long as you have... view full answer...
The DeeZee Specialty Series Wheel Well Toolbox with Drawers, # DZ95D, allows you to access your tools when the tail gate is open. This installation is behind your wheel well, but there will be space between this box and the side wall of your truck the dimension of which is based on your specific truck bed. The tool box has a quick release from its mount allowing you to move the toolbox and take it with you on the job, and this feature also allows easy removal to clean behind it as needed.... view full answer...