Installation of DeeZee Trailer Tongue Tool Box # DZ91716

Question

Question:

Im putting the box on a aluminum boat trailer. How does it install? Is there pre drilled holes and only holes need to be drilled into trailer? Are U bolts needed?

asked by: Angelo

0

Expert Reply:

The DeeZee Trailer Tongue Tool Box does not feature pre drilled holes, but the included sheet metal screws can be used to secure the box to the trailer tongue. The instructions call for 3/16 inch holes to be drilled through the bottom of the box into the trailer frame. Make sure you avoid any wires that might be running along the trailer frame. You can see the installation instructions by clicking the provided link. You could use u-bolts if you wish.

expert reply by: Mike L

0

Answer 1

Since you are not wanting to drill all the way through the aluminum frame on your H and H trailer, you can use U-bolts like #CE15283GA-2 to go around the frame of your trailer, and up into the RC Manufacturing T-Series Trailer Tongue Tool Box -…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Pace Edwards has two confirmed fitting Switchblade covers for your 2024 Chevy Silverado 3500 DRW 8' bed; part #PE87CV, which is an aluminum and vinyl mix and part #PE77CV, which is just aluminum.

view full answer...

Answer 6

To wire up the third brake light of your ARE camper shell will require you to find the third brake light circuit of your truck. The main trailer wiring harness is located under the truck bed, usually above the spare tire. There is usually a socket…

view full answer...

Answer 7

The best option we have for your application is the Dutton-Lainson StrongArm Electric Trailer Winch #TW4015. This has a 1,500 lb capacity rating, a cable, free-spooling drum, and a remote. The remote is wired, but it does allow you to move up to 10…

view full answer...

Answer 8

As it turns out, almost all trailer roof vents are 14" X 14", +/- 1/4". Your best choice is the MaxxAir #MA00-335001 Universal Replacement Lid. The continuous hinge versions are better than the 3-tab versions. The hinge on this unit is…

view full answer...

Answer 9

The outside diameter of the Wire - Jacketed 6-Wire - per Foot #DW04906-1 is 1/2" including the vinyl jacket.

view full answer...

Answer 10

I spoke with Knott AutoFlex Inc. and was able to get the needed information using the axle tag in order for you to add electric brakes to your trailer. I have attached a list of these parts below. Electric Trailer Brake Kit part #AKEBRK-35 Trailer…

view full answer...

Answer 11

I checked with Lippert and they told me that each of the jacks of the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 that mount on the trailer frame have a height range of up to 19 inches.

view full answer...

Answer 12

Yes, we have checked with Lippert in the past and their Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 is compatible with boxed frame RVs like your 2019 Outdoors RV Backcountry series Model 23KTS.

view full answer...

Installation of DeeZee Trailer Tongue Tool Box # DZ91716

Product Page this Question was Asked From

Continue Researching