There are a few different ways to get the indicator light from the Demco SBS Stay-IN-Play DUO Supplemental Braking System # SM99251 operating in your motorhome.
If you don't plan on using the brake controller circuit on your motorhome then you can connect the indicator to your motorhome by using that circuit. Tap in a wire from the stop light circuit on your towed vehicle to the connector at the front of your towed, making sure it corresponds to the brake controller pin on your motorhome... view full answer...
I have attached a photo of the wiring diagram for the Bulldog Winch Powersports Series ATV Winch part # BDW15002 and I have emailed the owner's manual to you separately as well. For further reference, if the winch only extends and doesn't retract or vise versa then odds are the relay just went bad and you do not need to replace the entire Power Unit part # BDW20115 to fix this, just the relay part # BDW20101 which you may want to just get a few extras of. view full answer...
You are right that the minimum recommended ground clearance is 11". Using the # BWTS20049B in its lowest position would leave one of the trailer balls lower than the vertical portion of the ball mount. There really is no work around in this case. B&W does not make a separate attachment with the balls at 90 degrees like you described. Maybe they should start making one though, this is not the first time this has come up. In some cases folks can get away with less that 11" clearance, but... view full answer...
It sounds like you have the older B&W RVK3000 5th wheel hitch. That was discontinued awhile ago, but I was able to track down some information. You should install the u-bolts from the inside of the base out, so the u-part of the u-bolt should be inside of the base with the 2 leg parts of the u-bolts coming out towards the cab.
Should you ever need to upgrade the base because the hardware is broken, missing or anything else, you can do so pretty easily by getting the Replacement Base for... view full answer...
We get this question a lot. The momentary push button on your Lippert LINC system that you need to press to program the Remote Control # LC292614 is not on the remote, but rather on the LINC receiver box which is usually located near the generator. After you press and hold this button on the receiver you will press the light bulb button on the remote until you hear a relay in the receiver click, then release that button on the receiver. The two should now be synced.
I have atttached further... view full answer...
If your 2013 DRV Mobile Suites 38RSSB3 currently has a Torklift GlowStep on it the Single Add-On Step for TorkLift GlowStep Kits # TLA7801 that you referenced would be all that you need to add an additional step. I attached a picture that shows all of the included hardware as well. view full answer...
I reached out to my contact at FloTool and the # FT11930MI wheel chocks are only rated for wheels that are 20 inches in overall diameter. They're designed for lawnmowers and golf carts and not trailers.
Instead I recommend the etrailer wheel chocks, part # 288-02011-2, which can be used with your 235/80R16 tires. I linked a video you can check out as well. view full answer...
At this time we do not currently have a video of the installation process of the Roadmaster # RM-152-LED kit on a 2017 Ford F-350, but as soon as we do get an opportunity to make one we will certainly be looking to take advantage. To install a Roadmaster Bulb kit like the # RM-152-LED you'll need to remove the tail light housing on your vehicle and just choose the best spot for a 1" hole to be drilled without interfering with any of the other lights or wiring components.
You could potentially... view full answer...
You should be able to wire the power for the camera located at the 3rd brake light so that it has constant power and then it is switched on/off manually. If the current camera doesn't have that capability then you can install the Truck Bed Cargo Camera for 8" Factory Monitor - Switch Kit # 3460001 on the 2019 Ford F-350 and it can be wired this way. I reached out to my contact at GCH Automotive who confirmed this. The only thing that you'll have to check out is if Ford automatically "locks... view full answer...
The Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate # VG-15-4000 (which is confirmed to fit your 2017 Ford F-350) does feature a keyed center release mechanism to protect your cargo, however you will need to use the two included keys for operation. The lock core cannot be keyed alike with your truck's ignition key fob.
I have attached a short video demonstration that you can check out as well. view full answer...
According to EcoHitch, for a 2019 F350 the install procedure for the Diesel model is very similar to what's shown in the install video for the F250 gas engine model I've linked for you.
The only difference is that the front heat exchanger is relocated using brackets that are supplied with the hitch. This is specifically outlined in the installation instructions. The transmission lines do have enough slack that the exchanger can easily be relocated. view full answer...
Attached is a clip from the instructions on how to bleed the brakes after installing the Demco Hydraulic Brake Actuator # DM8204311 that you referenced. You can use the Powerbuilt Brake Bleeder # ALL648591 to assist you in this process. view full answer...
To replace the electric brakes on your 2019 Grand Design Solitude 375RES you will first need disc brakes. For your 7K axles I highly recommend the Kodiak Disc Brake Kit # K2HR712DS because it has a dacromet coating and stainless steel calipers which gives them great corrosion resistance. The kit includes enough parts for brakes on 1 axle so you will need 2 of them.
For brake lines I recommend the HydraStar Hydraulic Brake Line Kit # HS496-252 which gives you a steel main line but then... view full answer...
Both of the red wires on the Custom Third Brake Light Camera for 8" Factory Monitor # 3460006 will connect to power on your 2015 Ford F-350, while the black wire needs to be connected to ground. When we installed this wiring kit on a 2015 F-350 we used a fuse tap # F2526 to fuse location 44 (auxiliary switches) on the passenger fuse panel. To get this whole system to work properly you will want to have both red wires connected to continuous power so that when you flip the switch it will... view full answer...
In order to get the correct replacement support arm for your Solera awning, what you want to do is measure the wall mount of your awning. All you need to do is measure the length of that mount, and that measurement will let you know which support arm from the following options you need to get.
- 61 Inches - Black: Solera Short Awning Support Arm # LC351829 (a pair)
- 63 Inches - White: Solera Short Awning Support Arm # LC97UD
- 66-1/8 Inches - White: Solera Pitched Awning Support Arm... view full answer...
The reason why the Level Command II, # F2219 has an inflate and deflate button on each side is because, it is designed to allow you to adjust each air bag independently of the other. This feature for drivers that frequently carry various types of loads in the truck. view full answer...
There is a way to remove just the head without tools of the Reese M5 5th Wheel Trailer Hitch for Ford Towing Prep Package # RP30922.
According to the instructions, to do this you just pull the spring clips off the head retainer pins, and then pull the head retainer pin out of the head. view full answer...
The best way to install the lighting for the B&W Custom Headache Rack w/ LED Lights # BWPUCP7502BA on your 2019 Ford F-350 is to connect them directly to your vehicle lighting system. As you have found out the newer Ford pickups have a "smart" harness that senses when a trailer is connected. The only way to prevent your Super Duty from thinking that a trailer is connected when you have this headache rack installed is to wire it directly to your truck OEM wiring.
Please note that you will... view full answer...
The installation of the Adjustable Width Trailer Hitch Receiver # 13703 is pretty straightforward and there aren't any shortcuts that would make the installation easier.
Attached is an installation video as well as the written instructions for you to reference. This trailer hitch fits trailers with a frame width between 22" - 72". view full answer...
The Clazzio Custom Seat Covers # AL-EAFOB7257BK won't be difficult to install on your 2022 Ford F-350, but it will take a little bit of time. It's more about taking your time than having issues with fitment. The nice thing is the seat covers have adjustments on them so you get them in place and then tighten them up.
Attached is an installation video for you to check out! view full answer...
Go To Results