The Curt Front Mount Trailer Hitch Receiver part # 33055 is what I recommend for a Fleetwood Tioga 31 Class C Motorhome on Ford E-450 Chassis. view full answer...
We actually sell a version of the LaSalle Bristol Cable-Actuated RV Waste Valve for Gray Water Tank # 34466N11AB72GMA that you referenced in a 48 inch long cable version as part # 34466N11AB48GMA.
I would not recommend attempting to shorten the cable nor do we have a way that it could be done safely. view full answer...
I recommend the Tekonsha Prodigy P2 Trailer Brake Controller, part # 90885, along with the plug-in Wiring Adapter, part # 3035-P. The install will be very easy actually. If you check out the help article I attached you will see that there is a port under the dash of the van that will allow the controller to easily install.
I also attached an install video for you to check out as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885 because this... view full answer...
The Draw Tite hitch part # 65022 is a fit for a 2003 Ford F-550 cab and chassis like what your motorhome is built on. You can verify the fit though by measuring the width of the frame. If your motorhome has a frame that measures 34 inches apart from outside to outside this hitch will fit. view full answer...
The Blue Ox hitch extender # BX88265 (10,000 pound towing capacity) and Roadmaster trailer hitch extension # RM-071-75 (6000 pound towing capacity) will be capable of flat-towing your Jeep Wrangler weighing 4300 pounds. Adding a hitch extension to flat-tow a vehicle will not decrease the rated towing capacity on the hitch extender. There isn't as much stress on the tongue.
For traditional towing the towing capacity will reduce by 50 percent by adding a hitch extender.
Also, these two hitches... view full answer...
Sounds like you have a hitch mounted pintle mount like the part # C48190 and are looking for a hitch mounted platform like part # BWPMHD14005 for it to attach to. view full answer...
We have what you need. It sounds like you have a 4-way round on your trailers like the part # PK11404 already installed on your trailer. So what you will need to do is first cut the 4-way off of your tow vehicles and then wire the wires that previously ran to the 4-way to the Harness part # PK11998. You will want to run the running light circuit to the brown wire, the ground to the white wire, the left turn/stop circuit to the red wire and the right stop/turn to the green wire. The rest... view full answer...
I have a solution for you but the Draw-Tite Front Mount Trailer Hitch # 65022 that you referenced is confirmed to fit the 2006 model Ford F-450 cab and chassis model vehicles which isn't what you have.
The Draw Tite Front Hitch part # 65001 is designed to fit the RV E-450 cutaway chassis and would be the correct front hitch for you. view full answer...
I have a solution for you, but the Roadmaster Dual Hitch Receiver Adapter # RM-077-4 that you referenced is only designed for flat towing vehicles so I cannot recommend it for you.
Instead you would want the Curt Multipurpose Ball Mount part # D210. This will let you tow your boat with the ball mount and then use a carrier on the top hitch opening. The unit itself has a 7,500 lb towing and 750 lb tongue weight capacity while the top receiver has a 350 lb tongue weight capacity. view full answer...
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.
Finding the brake controller connectors on those cutaway chassis E450 models can be challenging. When Ford sends them to out to aftermarket, they are used for several different vehicles, like RVs, ambulances, moving vans, delivery trucks, etc. During this process the under-dash wiring can be moved around... view full answer...
Yes there will be a fuse that protects the 12 volt trailer accessory circuit of your 7-way wiring. If this is factory wiring of a truck you'll want to check out the fuse box diagram or the owners manual. view full answer...
For your camera system, I recommend the Rear View Safety Backup Camera System with Trailer Tow Quick Connect Kit - 2 Cameras # RVS-776614-213. this system comes with the license plate camera, the connection cord and the rear camera for your trailer. You will just want to make sure the trailer camera has a power supply from the running light circuit so it has a constant view. view full answer...
I do have an option for you but there is not a custom bolt-on trailer hitch available for your 1999 Fleetwood Tioga Class C Motorhome on a Ford E-Series Cab and Chassis. That said, the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver part # 41991-16 would be a good choice for you as it has the Class V rating you are after and the tall universal brackets will work on most frames via either bolting or welding. view full answer...
Great News! We have the replacement Flow Through Tire Sensors for TST TPMS Systems part # TST-507-FT-S2. These will easily pair with your current TST monitor allowing you to monitor your pressures and also check them easily with the removable caps.
These come as a 2 pack so just order the quantity you need. I have linked them as well as the instructions for pairing them if you do not still have the user's manual. view full answer...
The front mount trailer hitch we offer for a 2013 Ford E-450 RV Cutaway is the Draw-Tite Trailer Hitch, part # 65053.
For a hitch-mounted spare tire carrier I recommend part # C31006. This is a universal spare tire carrier. I have attached a photo of the carrier with some dimensions noted you can check out. view full answer...
The only styles of hitches that can be made to fit a service body truck like yours are multi-fit RV hitches like the # 41990 that has a 16k capacity. This is a weld on hitch that would require either the 7 inch drop brackets part # 4907 or the 16 inch brackets part # 4916.
The rear ends on service bodies are all different dimensions so there's no way to have a hitch fit that works well with that vehicle configuration. view full answer...
The replacement converter you'd need for your Parallax 7345A is the part # PD4645V. This has all of the same slots for fuses and breakers that you have now so it would work well. view full answer...
As long as your E-350 van doesn't have the OEM steering dampener installed, you'd use the Roadmaster
# RM-RBK2-RSSC you'd looked at.
The two best investments in the handling issues with the long wheelbase Ford E-Series vans is installing a steering stabilizer and a rear anti-sway bar. The steering stabilizer is where I recommend folks start, because the majority of the time the steering stabilizer does the trick but if it doesn't completely solve the wandering issue the addition of an... view full answer...
If you have the F550 cab and chassis model, your best bet would be to go with a front mounted hitch like # 65022 then, depending on the size of the boat, you might be able to use a goal post rack like # EM07600-07601. This rack has a weight capacity of 400 lbs, but you will want to check your owners manual to find the weight capacity of your roof. The bars will support boats up to 52" wide.
Finally you will want Rightline GearKayak Carrier with Tie-Downs # RL100K10. The foam blocks provide... view full answer...