The inlet/outlet/tubing diameters listed from Magnaflow are OD, outer diameter, not ID, inner diameter. If your tubing is 2.5 OD you will have to butt-weld the muffler to the exhaust tubing, the exhaust pipe will not slide into the muffler. Any muffler shop can do this.
The MagnaFlow muffler, part # MF10416 is not designed to be a slip fit muffler. Your exhaust tubing would need to be designed for slip fit mufflers and have band clamps to apply sufficient pressure to seal the system. This... view full answer...
The shipping weight of Draw-Tite trailer hitch # 75305 is 48 pounds. That includes the packaging so the hitch itself weighs approximately 46 pounds.
If you plan on doing some towing with your 2006 Chrysler Town & Country the recommended ball mount is # 36071. It comes with a pin and clip. Then for a 2 inch ball, you can use # 19258.
And for trailer wiring you can use wiring harness # 118300 to add a 4-Way flat connector to the rear of the vehicle. view full answer...
The distance from the center of the hitch pin hole of etrailer.com Trailer Hitch Receiver # E98854 to the edge of the rear fascia (or the edge of the rear bumper) on your '10 Town and Country is approximately 4 inches.
For wiring which will give you a 4-way connector and allow you to power your trailer's lights you need Wiring Harness # 118552. I also recommend checking out Ball Mount Kit # 989900, which is for 2” hitches and may fulfill your towing needs in one tidy package; two ball... view full answer...
The parts you'd need for your 2008 Chrysler Town and Country with raised rails are the Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 and Legs # RRSX100. view full answer...
Getting the correct rise/drop is important but if you can't get it totally exact it's not that big of a deal. Getting it pretty close is often times just as good. This is why there aren't ball mount rise/drop figures available in every possible height. On a vehicle like your 2012 Chrysler Town and Country that is going to have some suspension sag when the weight of the trailer is put on the hitch it typically works out the best to have the rise/drop from the ball mount on the higher side... view full answer...
According to the manual for the Jensen LED Television with DVD Player # JTV1917DVDC, which I have sent to you, the power consumption is 28 watts. This LED television is 19 inches, HD ready, and comes with a tabletop stand and wireless remote control. It also has a VESA 75mm x 75mm mounting pattern if you want to mount it on your wall. view full answer...
The max height and drop on the Reese Light Duty Weight Distribution System # 66557 is 8 inches of rise and 2-3/4 inches of drop. This is determined by measuring from the top inside edge of the receiver to the top of the ball platform.
To determine the correct amount of drop that you will need in a weight distribution shank you will want to measure from the ground to the top of your trailer hitch receiver, which is your hitch height, and from the ground to the bottom of your trailer coupler,... view full answer...
In the installation video for Draw-Tite hitch # 36455, which I have linked for you at right, you can see the position of the installed hitch at the 1:20 mark. This shows an underside view of the 2011 model year's rear bumper after hitch installation. I have also linked a screen shot image with an arrow to indicate the distance between the edge of the receiver tube and the rear edge of the bumper - just about 5-inches.
You can use this measure to compare to the clearance provided by your... view full answer...
The towing weight capacity of your 2007 Chrysler Town and Country ranges from 1,700 lbs to 3,800 lbs depending on what your Town and Country is equipped with. You can consult your owner's manual to find out your specific towing weight capacity and if you don't know what your Town and Country is equipped with you can take your VIN to a dealership and they can let you know.
Since the trailer that you are interested in looks like it could have a Gross Vehicle Weight rating (GVWR) of up to... view full answer...
A Class II trailer hitch would have enough towing capacity to pull your pop up camper, but we will want to make sure your 2007 Chrysler Town and Country is capable of towing that weight. According to the owners manual, your Town and Country would only have enough towing capacity to pull your camper if it came with a factory tow package. If it did not come with a tow package, the maximum towing capacity is 1,800 lbs.
To determine if your van came with the tow package, I recommend contacting... view full answer...
The top of the receiver tube for the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 that you mentioned sits level with the bottom of the brackets that mount to the underside of your trailer frame so you will want to use the Curt option for your setup.
The Curt option, part # 13703, has a measurement of 8-1/4 inches from the beam to the edge of the hitch receiver and a measurement of 2-3/4 inches from where the beam inserts into the bracket to the edge of the bracket... view full answer...
The Swagman bike rack part # S64650 that you referenced can accomodate bike tires that are up to 3.5 inches in width. Yours being 3 inches wide would work easily with this. view full answer...
When we installed the Curt hitch part # C12264 on similar 2011 Chrysler Town and Country we found that from the ground to the top of the hitch opening the distance was 11 inches. view full answer...
Yes, the Replacement Awning Extension Rod for Solera Slide-Topper Awning # LC3452072 that you referenced measures 3/4". I actually recently took this same measurement for another customer for the white version part # LC3452071 and I'm attaching the dimensional photo for you to reference. view full answer...
The WeatherTech Side Window Air Deflectors, # WT82476, include deflectors for the front and rear driver's-side and passenger's-side windows of your 2014 Chrysler Town and Country.
The deflectors for the front windows are actually longer than those for the rear doors due to the fact that they line more of the window. For the front windows the deflector begins near the side mirror and then runs across the top of the window where as the deflector for the back window just runs the top of the... view full answer...
Trailer tire speed ratings do use a letter code system. A tire rated L for speed means it can be operated up to 75 mph; a tire rated M for speed can be operated up to 81 mph. There are many other speed codes. A trailer tire that does NOT indicate any specific speed rating on its sidewall should be presumed to be rated for 65 mph. If your tires do not indicate a speed rating that is molded right into the tire's sidewall then you should go by what the trailer documentation says.
It is possible... view full answer...
The Tow Ready loop, part # TR63046 measures 7-1/16 inches from hitch pin hole to center of tow loop.
The Bestop Loop measures about 6-5/16 inches from the hitch pin hole to center of tow loop. The version I have in front of me also uses a red shackle bolt. view full answer...
Dexstar wheel # AM20422 does not comewith a valve stem, the diameter is 0.453 inches.They do not provide PSI ratings with the wheels so you would go by the tire size that fits this wheel; 205/75-15. The highest capacity tires in this size we currently carry are rated for 65 psi. view full answer...
You won't have any problems using the Extra Long Ball Mount, # BM20 by Brophy, on your 2012 Chrysler Town and Country as long as you have a 2-inch receiver on your hitch. This ball mount has a 10,000 lb gross trailer weight capacity and a 1,000 lb tongue weight capacity. Be sure you do not exceed the capacity of the lowest rated item while towing. You may also want a hitch ball, # 19247 or #19260.
If you want to know the measurement for the extension, then you will want to start from... view full answer...