How Far Out Does the Hitch Receiver Extend on the Curt Adjustable RV Hitch Receiver # 13703
Question:
Hi, I am looking for a hitch for my travel trailer. There are two models you sell that can work but I need some measurements to help me decide which will be best On the UF35-946403 I need to know if the top of receiver tube is level with the bottom level of the frame the hitch is welded to. I need it to be at least 1/8” lower to clear a cross bar. Also need to know how far the receiver tube extends beyond where hitch is welded to the frame, the edge of weld closest to the back end of trailer. On the Curt 13703 need to know how far the receiver tube extends beyond the edge of attachment plates to frame, the edge closest to back end of trailer. What I am trying to find out in both cases is where the opening to receiver tube is going to be in relation to the back end of my trailer. I am sure a lot of other people would also find this helpful. Thanks
asked by: Terry S
Expert Reply:
The top of the receiver tube for the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 that you mentioned sits level with the bottom of the brackets that mount to the underside of your trailer frame so you will want to use the Curt option for your setup.
The Curt option, part # 13703, has a measurement of 8-1/4 inches from the beam to the edge of the hitch receiver and a measurement of 2-3/4 inches from where the beam inserts into the bracket to the edge of the bracket nearest the rear of your trailer. This means that the edge of the receiver itself will extend 5-1/2 inches past where the bracket stops (see attached photo). This will give you an idea of how where the receiver will sit on your setup.
If you let me know what you will be using the hitch receiver for I can make some recommendations for you.
Products Referenced in This Question
Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- RV and Camper Hitch
- Frame Mount Hitch
- 22 - 72 Inch Wide Frame
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Bolt-On
- Weld-On
- CURT
more information >
Product Page this Question was Asked From
Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames
- RV and Camper Hitch
- Frame Mount Hitch
- 47 - 77 Inch Wide Frame
- 350 lbs TW
- 2 Inch Hitch
- Weld-On
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers - 36" Long
- Search Results: hitch extender
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Do Holes Need To Be Drilled Into The Adjustable Arms Of The Stromberg Carlson Adjustable Hitch
- Q&A: How to Determine if Torsion Lift Kit Will Fit Winnebago Micro Minnie
- Q&A: Will Ultra-Fab RV Trailer Hitch Receiver Extend Past Rear Bumper On Winnebago 2106 Trailer
- Article: How to Carry Bikes While Towing a Travel Trailer
- Q&A: Mounting Options For An Ultra-Fab Trailer Hitch Receiver On A 2019 Grand Design Imagine 2600RB
- Q&A: Installing Mount-n-Lock SafetyStruts to Tube Frame
- Q&A: What Side of Trailer Frame Does Mount-n-Lock SafetyStruts Install
- Q&A: Trailer Hitch For Forest River Wildwood 29VBUD
- Article: Trailer Wiring Diagrams
- Article: Carrying Bikes While Towing a 5th Wheel Camper Trailer
- Article: How to Raise Your Travel Trailer Height
- Article: What is an RV-Approved Bike Rack? (And Do You REALLY Need One?)
- Article: Best Hitches for Travel Trailers (2022) - For a Smooth, Sway-Free Ride