With the vehicle only having a 1000lb towing capacity for the vehicle you would only have a 100lb tongue weight capacity so hauling a cargo carrier with 225lbs on it would exceed the capacity of the vehicle and the hitches that are available for this vehicle. There are adapters that can give you a 2" receiver but the downside is that adapters reduce the overall capacity of the hitch by 50% so you'd end up with too little capacity to haul your Vespa.
The only way you'll be able to safely... view full answer...
The PT Cruiser started in the 2001 model year. They were not being produced in 1998. I used to have a 2003 model myself. The good thing about the PT Cruiser is that the body style pretty much stayed the same its entire lifespan. I have used Thule trunk mount bike racks on my 2003 model and they are a fit and work well.
The Thule Passage 3 # TH911XT does fit both the first and second generation PT Cruisers. So in other words, the entire run of that vehicle.
I can offer some fit tips since... view full answer...
I checked with Thule and the confirmed that the Thule Passage 3 Bike Carrier # TH911XT that you referenced is a confirmed fit for your 2006 Chrysler PT Cruiser.
I attached a review video for this rack for you to check out also.
If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Thule Bike Adapter Bar # TH982XT to provide a horizontal top tube on your bikes to provide an attachment point. I attached a review... view full answer...
You didn't mention which bike rack you have, but luckily enough one of my co-workers has a PT Cruiser that he uses a trunk mounted bike rack on. He agrees that getting those top hooks in place can be a challenge, but he's found that it's easier if you insert them at the top corners of the hatch, because the gap between the hatch and the vehicle is wider at that point. Once you have them inserted, you can slide them over more toward the center of the hatch.
If this doesn't work for you,... view full answer...
Though the kit you mentioned is designed for a different tow bar, there is a similar option for a Falcon 2 tow bar. We also do indeed have all the parts needed for you to flat tow your 2005 Chrysler PT Cruiser with that tow bar, and I'll list out all the parts you'll need to make it easy to order.
- Base Plate Kit: Roadmaster Crossbar-Style Base Plate Kit # 278-1
- Tow Bar: Roadmaster Falcon 2 Tow Bar # RM-520
- Wiring Kit & Safety Cables: RoadMaster Falcon 2 and Falcon All-Terrain Combo... view full answer...
We do have several trailer hitches designed to fit the 2003 Chrysler PT Cruiser, including the Curt Trailer Hitch, # C11132, that you have referenced. I have included a link to the available option below as well as a link to the installation instructions for the Curt hitch.
The available trailer hitches for the 1998 Dodge/Plymouth Neon will not fit the 2003 Chrysler PT Cruiser. The trailer hitches for the Neon were designed to fit its unique frame which differs from the PT Cruiser. The... view full answer...
The CURT Trailer Hitch, # C11132, will fit all models of the 2005 Chrysler PT Cruiser which would include the convertible.
If you plan on doing some towing, the hitch comes with a ball mount, pin and clip. For a ball you can use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring, use # C55532. I have included links to the installation instructions for the hitch and wiring for you. view full answer...
The SportRack Semi-Custom Roof Rack, # SR1005, will fit on your 2001 Chrysler PT Cruiser as long as your roof has not existing roof rails or crossbars. This roof rack was designed to mount directly to the roof of your vehicle and uses clamps that hook to the door jamb (see photo).
Other than the roof rack accessory you are interested in (bike rack, cargo box, ski carrier, etc.) you will not need any additional parts to mount this roof rack to your vehicle.
If you would like a recommendation... view full answer...
Edge offers some performance monitors, like part # EP84130, that are compatible with your vehicle. They would monitor different operating parameters like engine load, real time and average fuel economy, RPM, electrical system voltage among others. (Not all parameters are available for all applications). They will monitor the parameters, but not allow any changes to be made to factory settings.
The Bully Dog Triple Dog GT is not available for the PT Cruiser platform. None of the other performance... view full answer...
The FitDial setting for a Thule Archway 3, part # TH910XT is 10 on both sides.
Additionally, Thule adds the following tips for attaching this rack to your 2006 Chrysler PT Cruiser:
- Place your top clips in the gap at the front edge of the top of the hatch.
- Place lower clips in the bottom edge of the hatch
- Don't use your rear wiper blades while the rack is installed.
- Lower arm of carrier should sit on the upper tier of the bumper
- Remove the rack when its not in use to preserve... view full answer...
The Curt Trailer Hitch, # C11132, will fit all models of the 2006 Chrysler PT Cruiser which would include your convertible. I have included a link to the instructions for you.
If you plan on doing some towing, the correct ball mount is # C45520 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # C55532. I have linked the instructions and a video showing a typical installation of the wiring. view full answer...
We do indeed offer two sizes of replacement end caps for Yakima round crossbars.
We offer the smaller diameter # Y80159 that you referenced, and the larger diameter also in a set of four pieces as part # Y8007026. These larger diameter end caps fit all round Yakima crossbars except for the 86-inch size. This larger end cap is also offered in single units as part # Y8790009.
To give you some advance assurance that these larger caps will fit your crossbars I have pulled a set of part #... view full answer...
Get the Curt Trailer Hitch Receiver # C11132 for your 2009 Chrysler PT Cruiser as it comes with all the hardware you need to install with no welding needed. You'll need a ball mount # C45520 and a hitch ball. Either 1-7/8 inch # C40001 or a 2 inch # C40018. If you do have a trailer you plan on using, you will need some wiring # C55532. Depending on what you plan on hauling. I've included a video for you to see how it installs! view full answer...
Thanks for the photo for clarity. The Rhino-Rack Fishing Rod Carrier - Locking - 8 Fishing Rods # RR574F won't have any issue with the curved crossbars. The 6.5 foot sections of the 13 foot surf rods should work very well for this application.
With the curve of the roof the reel will be the only issue and you can have that rest on top instead of underneath if desired. Obviously gravity will have an impact on that, so you will need to plan accordingly. view full answer...
There is a single option to use a hitch adapter and extender that will work with the Class I, 1-1/4" Curt Trailer Hitch # C11132 that fits your 2003 Chrysler PT Cruiser, the the Brophy Trailer Hitch Receiver Adapter - 1-1/4" to 2" Hitch # HTAD. view full answer...
Yes the Roadmaster Falcon 2 will attach to your PT Cruiser with Blue Ox base plates. I have provided a link to our video review and the instructions for this item. view full answer...
You are correct that the Curt Trailer Hitch Receiver # C11132 does require the use of Stabilizing Support Strap # 18050 when using it with accessories like a bike rack on your 2005 Chrysler PT Cruiser. view full answer...
I did some checking and it looks like the SportRack Frontier Roof Rack # SR1005 will fit both a 2003 and a 2005 Chrysler PT Cruiser. view full answer...
Yes, the Roadmaster base plate kit # 278-1 is a fit for your PT Cruiser. This base plate kit features computer-cut powder-coated steel construction and installs with included hardware and no welding. This is compatible with the 5000-pound capacity RoadMaster Tracker Tow Bar, part # RM-020.
A tow bar bracket and tow bar are just two of the components required by law to safely tow your auto. The other required parts include a wiring harness for tow lights, safety cables and a tow bar braking... view full answer...
To get the replacement installation hardware for Curt hitch # C11132, you'll need to go to the # RHK product page. From there, enter "C11132" in the "Hitch Item Number" box, then select "Curt" from the Manufacturer drop-down box and you'll be set. view full answer...