Expert Answers about Buick
- Warranty Coverage of Bulldog Powered-Drive Trailer Jack # BD500185
- The Bulldog Powered-Drive Trailer Jack you mentioned, part # BD500199 is covered by a 5 year Limited Warranty. If you click the provided link, you can see a video showing the jack being installed.
view full answer... - How Theft-Proof is the etraiiler.com Coupler Lock # e98888
- Locks are for keeping honest folks honest, just about any lock can eventually be defeated if the crook is determined enough. The lock you mention, part # e98888, provides what I would call minimal deterrence against theft. If there are two identical boat trailers parked side by side, one using the # e98888 lock, and the other unlocked, the lock will do its job and deter the crook from taking your trailer.
One quick snip with some bolt cutters, and the lock will be defeated, but the thief...
view full answer... - Is 40 amp Breaker Included with ETBC7 Sufficient for Use with 10 Gauge Wire
- The duplex cable included with the ETBC7 kit uses 10 gauge wire, which is appropriate for handling a circuit with a maximum of 40 amps with a run of 25 feet or less.
We sell thousands of these kits per year, and have never had a reported problem with the gauge of wire being insufficient. Keep in mind that the primary purpose of this circuit is to maintain (not charge) a trailer mounted battery or to power a trailer mounted accessory requiring limited amperage, such as interior lighting....
view full answer... - Locating the Model Number for a Replacement Tail Light Lens
- The lens will typically have a DOT number, but not a model number. A replacement lens is usually determined by the model number of the light itself. There should be a model number printed on the back of the light.
If you have a square incandescent over 80 inch light like the Optronics Submersible Trailer Light, # ST5RB, that you referenced, then the Replacement Tail Light Lens, # A8RB, on your light.
If not, then you can send me the model number of the light you have and I can make...
view full answer... - Determining the Leaf Spring Drop From an Empty Trailer to a Fully Loaded Trailer
- The drop that you will experience with the 3-Leaf Double-Eye Spring for 2,500-lb Axles, # e66SR, from a trailer at zero load to full load is going to be 1-1/2 inches.
A few things to note with a fully loaded trailer is that you will want at least 3 inches of clearance above your tires and 2 to 2-1/2 inches of clearance from the top of your axle to the bottom of the frame where the leaf spring hangers are welded.
You will also want to get the correct hanger kit for the leaf springs you...
view full answer... - Is the Master Cylinder for the Model 60 Brake Actuator Fully Enclosed
- The actual master cylinder that is used in the model 60 actuator, # T43397007K, is part # T4395100. This style uses the metal cover and the gasket pictured and is held on with 4 bolts. The model 6, 10, 20, and Ultra-70 use a fully enclosed master cylinder.
view full answer... - Is The Kenda Karrier ST205/75R14 Radial Tire w/ 14" Series T09 Aluminum Wheel # AM34659 Balanced?
- The Kenda Karrier ST205/75R14 Radial Tire w/ 14" Series T09 Aluminum Wheel # AM34659 does not come balanced. Trailer tires do not require balancing like vehicle wheels and tires since their primary function is weight supporting. As it is an aluminum wheel only stick on weights should be used if you plan to take them to a tire shop to have balanced.
We do have the Counteract Tire Balancing Beads available in a Single # CA66VR or 4-Pack # CA83VR. These beads allow the tire to always be...
view full answer... - Are RV Tankless Water Heaters Propane
- Yes, all RV tankless water heaters such as my preferred model, the Excel RV Tankless Water Heater, # EX93FR are designed for liquid propane (LP). They will have an electric source only for the purpose of providing ignition spark.
view full answer... - Running Ground Wire From Optronics Plug-N-Go Bracket On Non-Metal Trailer
- Unfortunately, the Optronics Trailer Light, part # A67CBPG is grounded through the mounting hardware which will not work on your non-metal trailer.
You can use grounding wire like part # DW02359-1 and attach it to the grounding tab on the bracket and run it to the ground you had for your old lights. You need to be aware that this bracket is designed for watertight connections and running additional wires from the bracket could compromise the watertight feature.
view full answer... - Does The Air Lift LoadLifter 7500 XL Have An Internal Jounce Bumper?
- Yes, the Replacement Air Spring for Air Lift LoadLifter 7500 XL System # AL50236 does have an internal jounce bumper.
This air spring is a replacement hybrid spring for your Air Lift LoadLifter 7500 XL Air Helper Spring System, and is made in the USA.
I have also included a product overview video for you to check out as well.
view full answer... - Is The Optronics LED RV Dome Light w/ Switch # RVILL50 A Cool Or Warm Light
- The LED RV Dome Light w/ Switch # RVILL50 offers more of a warm white rather than a cool white. I've attached a photo from a customer where you can see the difference between these lights on the bottom and some cool white lights up top. These will be less of a warm light than your traditional incandescent lights but still fall under that warm light category.
view full answer... - What is The Warranty On The Wireless Remote Kit for Bulldog Winch Standard Series Off-Road Winches?
- The Wireless Remote Kit for Bulldog Winch Standard Series Off-Road Winches # BDW22SB comes with a 1-year manufacturer defect warranty.
view full answer... - Shackle Straps Touching Frame With Road Armor Equalizers
- If the shackles are touching the frame when using the Road Armor Shock Absorbing Equalizer Kit # LC696740 it does indicate the shackles are too long, and since you mentioned you had 3-1/8" shackles, you can use shorter ones which can help.
I recommend going with 2-1/4" straps, the Replacement Shackle Strap for E-Z Flex Heavy Duty Rubber Suspension System # 018-024-01.
view full answer... - Is The Superwinch LT2000 ATV Winch A Quiet Winch
- The Superwinch LT2000 ATV Winch - Wire Rope - Roller Fairlead - 2,000 lbs, part # 1120210, is described by Superwinch and etrailer as being quiet.
I included a video installation link below if you wanted to hear how quiet the Superwinch LT2000 can be. You can hear it in operation at the 17 second mark.
view full answer... - Does Malone Top Tier MPG493 Kit Require Painting
- The Malone # MPG493 TopTier Load Bar Kit has uprights constructed of galvanized steel that shouldn't need painting. Actually, it's fairly difficult to get paint to stick to galvanized steel, some would say its impossible.
The crossbars are vinyl coated, and wouldn't require painting.
view full answer... - LMX Industrial Strength L11390 Thickener and Viscosity Specs
- The LMX # L11390 red grease is a lithium complex grease that has a # 2 viscosity index.
view full answer... - Lug Nut Torque for 16 Inch 8-lug Wheels
- The lug nut torque will depend of the diameter of your wheel studs and the construction of your wheels.
• For a steel wheel and a 1/2 inch stud, torque the lug nut to 90-120 foot lbs
• For a steel wheel and a 9/16 inch stud, torque to 120-140 foot lbs
• For an aluminum wheel and a 1/2 inch stud, torque to 90-100 foot lbs
• For an aluminum wheel and a 9/16 inch stud, torque to 120-140 foot lbs
It's recommended that you check the torque after traveling 50 miles, then periodically after that.
view full answer... - How To Remove Optronics LED Clearance or Side Marker Light # MCL40RB For Replacment
- To remove the Lens # A44RB from the LED Clearance or Side Marker Light # MCL40RB you will need to place the tip of a flat head screwdriver between the lens and light assembly(see image). I recommend starting near the corners to reduce the risk of damaging the lens.
Once you have the lens removed you will see the screws used to mount the lights. As this hardware is provided by the trailer manufacturer I cannot tell you exactly what it will have but a Philips head button screw is most commonly...
view full answer... - Are The Magnets Safe to Clean With Brake Cleaner On Dexter Trailer Brakes?
- Yes, you can clean the trailer brake magnets and other components on the Dexter Nev-R-Adjust Electric Trailer Brake Kit # K23-478-479 with brake cleaner. Be sure to dry the surfaces before reassembly.
view full answer... - How to Use a MaxxAir Fan With a Yetti 500 and Bluetti E3ba
- I am not completely sure what parts the Bluetti uses because it is not a product that we carry. But since both use the 12v outlet port, I would rewire the fan to use the male end of the Accessory Plug and Socket Kit # PE53QV. Since both of your power stations use a 12v cigarette outlet port, this would be the easiest route.
view full answer...
Go To Results