Summer Starts Here - Save up to 70%
4" x 2" Rectangle. Trailer light serves as a side marker, turn signal, or clearance light when properly mounted. Built-in reflex reflector. Black ABS plastic base. Surface mount to trailer - hardware not included. 2-Wire pigtail. P2 rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody. This is Jeff at etrailer.com. Today I'm gonna take a look at this Optronics LED Trailer Clearance Turn Signal or Side Marker Light with the Reflex Reflector in the Red Lens. Now, this is a rectangular LED trailer light that'll function as a side marker light, a clearance light, or a turn signal light. You can see, it is a red lens over three wide LEDs, and it does use a built-in reflex reflector to remove the need for a separate reflector. Now, I have this hooked up to some 12 volt power, and I do wanna show you the light.
So, what we're gonna do, is go ahead and turn on the 12 volt power. And there's your side marker light or clearance light. And then, we'll go ahead and turn off the overhead lights. And if you do hook it up as a turn signal light, you can see that it'll also offer the turn signal function. Now, they do use LEDs.
They do make great replacements for the incandescent lights, 'cause they'll last 50 times longer. They are more efficient, they provide brighter light with less power output, and of course, no bulbs to replace or (indistinct) to break. And the lifetime warranty on LEDs. Now, this is a durable, I'm gonna go ahead and disconnect it from our power here. The base on it is a durable black ABS plastic base.
The lens is a nice, easy snap-on acrylic lens. Very easy to replace. And again, this is compatible with 12 volt DC electrical systems. It is designed to mount onto the surface of the trailer. Now, the hardware installer is not included.
You can see, it offers a three wire pigtail, with the two power leads in the ground wire. And this light is DOT, Department of Transportation, compliant. It is also P2 rated. Few specs on this. The overall length, we'll get our ruler out here and we'll go to the back, overall length from one end to the other is right at four inches long. Height of it is two inches tall. And the total depth of it, one inch deep. Now, the distance between the mounting holes. These are the two mounting holes here that you mount. Center to center on those is right at three inches. And the power draw on this at 12.8 volts will be 0.06 amps. But that should do it for the review on this Optronics LED Trailer Clearance Turn Signal or Side Marker Light with the Reflex Reflector.
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
4" x 2" Rectangle. Trailer light serves as a side marker, turn signal, or clearance light when properly mounted. Built-in reflex reflector. Black ABS plastic base. Surface mount to trailer - hardware not included. 2-Wire pigtail. P2 rated.AS DESCRIBED, WORKS GREAT, DELIVERED ON TIME!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.