To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
These multipurpose, galvanized steel crossbars supply the backbone for your aftermarket roof rack system. Works with accessories that clamp around the bars. Pair with Yakima towers, fit kit, and RoundBar SL Adapter to create a complete roof rack.
Features:
Yakima 48" RoundBar SM:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today on our 2013 Honda Accord, we're gonna be test fitting the Yakima RoundBar roof rack system, consisting of part numbers Y00409. These are the round 50-inch crossbars for the Yakima roof rack systems. Part number Y00146, theses are the baseline towers for the Yakima crossbars. Part number Y03536, this is the RoundBar SL adapter for the Yakima baseline, Skyline, Timberline and Ridgeline towers. Part number Y06148 and Y006150, and these are the base clip fit kits that you're gonna need for your vehicle.The Yakima RoundBar roof rack system is great for carrying a wide variety of accessories on your rook or freeing up space inside your vehicle. These bars are tough and durable, and together have a combined carrying capacity of 220 pounds, but you always wanna check with your vehicle's manual to make sure you roof can withstand those weights.They're very easy to install.
They simple clamp around your vehicles doorframe. They come with these end caps here that just snap into place and also have a knock out for Yakima same-key lock system, which when installed, can secure not only your roof rack to your vehicle, but you can also make it key to like with whatever accessories you're installing on top of it.Now that we've gone over some of the features of the roof rack system, let's go ahead and show you how it installs. We already have our rear bar partially assembled on our table and we'll go through the rest of the steps. We'll start by installing our RoundBar adapter, starting with this plastic piece here that fits to the top portion of our tower. Just snaps into place.
We'll take our round bar adapter, which has this screw end on the bottom of it, line it up with that portion there, and we'll come to the end of this, pulling out this gray tab, flipping it upside down, going to the screw, which by loosening up that gray tab we can see now. Let's loosely install it at the moment. Then, we'll slide it on to the other end of our bar.We'll also install the pad portion of our fit kit. It just pushes in at the bottom of our tower until you hear a little bit of a click. Also, you wanna check your fit guide to make sure that this is in the proper notch.
If not, you loosen up the screw there and push it into its proper place. You can see that it moves our pad here. Once it's in its proper place, turn it to the side like that.Now, we're gonna measure it from tower to tower on the inside. Again, this measurement's gonna be in your instructions. Once you got that measurement down, we'll come back to that screw in the bottom here with our adapter piece and tighten it down the rest of the way.
You're gonna hear audible clicks once it's tightened down from our tool here. Like that. There you know it's tightened down enough and you're not gonna over-tighten it.Next, we'll put on our end caps here to hold everything in place. Do this on both sides.Now, we're ready to install it on the rear portion of our vehicle. We'll open up both doors to get ready to receive the rear cross bar. Set the bar in place. I want you to notice that I haven't put the clips in yet. I'm gonna do that in a second. I kind of saved that for the last thing that I do because I don't want the clips to possibly make contact with the roof of the vehicle and possibly scratch it. Make sure they're set evenly on both sides. Next, I'm gonna get the crossbar spread measurement. That's gonna be from center of the bar to center of the front bar. You'll find this measurement in your instructions as well.Next, I'll open up the little door here and our plate will slide to the inside like so. Then, we'll turn this screw. That's gonna lower our clamp onto our vehicle, as you can see there. We'll repeat this for the other side. Next, we'll tighten it down with the center screw here. Again, until you hear those two or three audible clicks. There we go. Then we can close that up. Then we'll put our end caps on. These two portions here fit into these hook portions there. Then they just snap into place. Now, we're ready to load up our gear and hit the road.There you have it for the Yakima RoundBar roof rack system on our 2013 Honda Accord.
Average Customer Rating: 4.7 out of 5 stars (220 Customer Reviews)
These multipurpose, galvanized steel crossbars supply the backbone for your aftermarket roof rack system. Works with accessories that clamp around the bars. Pair with Yakima towers, fit kit, and RoundBar SL Adapter to create a complete roof rack.Works perfectly. I am always impressed that Yakima continues to make parts for the "old roundbars" since they have since moved on to the superior JetStream bars.
I ordered the Yakima roof rack, with the Hullyrollers for the back crossbar and the Mako saddles for the front crossbar to use with my kayak. It arrived just like they told me and I put them on my car the eveningit arrived. Got to finlly use the roof rack on June 22 to go out kayaking and it worked great. Only thing is I did not know about the air reflector piece for the front crossbar. Now I will be ordering it to help with the wind noise.
Great rack, go on fast, easy to install and work well on my VW TDI wagon. Care has to be given and follow the instructions for the install to what type of rails you have. Works great carrying the VW luggage carrier and plan on using it to carry kayaks as well. Just have not decided what kayak rack type to get yet.
I've attachec a few pictures of the Yakima rack on my Audi Q7. It took a few attempts to find the right combination of attachments, but in the end, the pin attachments work best with the access points on the factory flush-mount rails. Great product!!!!!
Kimberly has shown that great customer service is not dead! etrailer and Kimberly are great to work with and have earned my business and will always be the 1st and last place I look for my rack+ needs!
As for the application, I needed more space to fit my cargo box on top of my 4Runner TRD Pro’s rack. I came up this this… Thank you!
roof racks showed up in great condition, and showed up as one package.... I should have ordered the J racks from here but I found them cheaper locally so Thule J racks compliment the whole setup and i am just about ready to hit the water :)
Everything from etrailer is timely and of good quality! The Yakima crossbars are no exception - they are indestructible.
The installation of this rack system went very well, all of the instructions were easy to read and use. I have attached some pictures of our installation. The vehicle is a 1994 Honda Accord EX four door sedan
Roof Rack 2008 Saturn Astra The roof rack arrived one day early...The packaging was excellent and the quality of the product more than met my expectations. The instructions made the insulation very easy. It took less than 45 minutes to install the unit complete.
Placed the order for the rack a year ago. I didn’t like the way it sat on the roof of my vehicle, but because I had already installed it, etrailer customer service refused to take it back. I would’ve gladly paid for the return shipping or some sort of restocking fee, but that wasn’t an option. I’ve had brand new rack and hardware sitting in their original boxes for a year.
Excellent selection of rack parts. Very useful installation videos help when choosing between products. Easy ordering process. Quick delivery.
One quick phone call and Gwendolyn figured out exactly what I needed for our new car to use my old Yakima rack.
necessary for using the widest cross bar option (78"). East to install
Everything arrived as promised and earlier than expected just installed. Looks like it will do everything I need it to which is haul around paddleboards. So far so good!
We got a Yakima Roof Rack system with locks and fairing for a "lime squeeze metallic" (Green...) 2011 Ford Fiesta 5dr Hatchback. Received the package yesterday and set it up within about an hour.
Great secure product though some written instructions on their setup and installation would be helpful.
Have been rocking my Yakima rack from etrailer.com for a year now. I am using rack in conjunction with a Tepui tent. Once I added the air deflector, I would say it's the perfect setup. The Yakima gives more clearance over the factory rack, so I was able to get my hands under it to secure the tent hardware. If you're thinking of upgrading your factory rack, I would not hesitate to use etrailer.com
The rack has been so useful since I purchased it. Staff at etrailer.com were exceptionally helpful in getting the best option for my car and answering questions. I recommend this company, for its 110% customer service, excellent prices and timely delivery.
The Yakima roof rack system is an Outstanding product. I purchased the product to replace the OEM roof rack because it was too flimsy to carry the tandem bike mount and my bike. The Yakima roof rack is solid and provides me the peace of mind while hauling my bike on the roof of my car. etrailer provided the product for the best price as always.
Haven’t used them yet but they should work as expected
We are so happy with etrailer. The product is high quality and it arrived one day before the expected day of delivery! Their customer services is exceptional - real people who know their stuff first hand. The installation was easy and is a prefect match for our Yakima Sky Box. We took the car to Zion National Park as shown on the photo taken at the Watchman Campground!
Roof rack on my 2005 Chevy Uplander. Also ordered the Q towers and fairing.
etrailer is excellent...however, not too pleased with Yakima and these cross bars - second set in four years...they make them out of a steel that rusts quickly...better out of stainless or aluminum. Maybe that is their idea of planned obsolescence. I also learned not to install end caps...that accelerated the corrosive process.
Of all of the many racks I’ve purchased over the years, this, by far, is the worst. Once installed, it is okay, but installing these towers is extremely frustrating. The front and back “clips” fall out requiring multiple attempts. When I contacted Yakima customer support, they acknowledged that they have received complaints about the product. Their solution was to just leave the racks on the car. I asked to be notified when a better product was available but a year later I’ve received no response. If this is the only option available for your vehicle (as it was for mine), then prepare to be frustrated. Otherwise, purchase a different product.
Kit worked perfectly on my 2021 Subaru Forester. The whole install took 30 minutes. Never been disappointed with etrailer.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.