This fishing rod holder mounts to your boat in seconds with a 4-1/2" vacuum cup. It attaches to most vertical, non-porous surfaces such as your boats' gunwales or sidewalls, or your vehicle while baiting your hook. Hard plastic construction.
Features:
Specs:
This heavy-duty rod holder frees up your hands while you fish. It mounts to most vertical, non-porous surfaces on your boat, such as your gunwales or sidewalls. You can also mount it to your vehicle for use as a holder while you bait your hooks or prepare your poles. It installs with a 4-1/2" vacuum cup that attaches and removes in seconds. If you need to adjust the angle simply detach the vacuum cup and reattach at the desired angle. The holder is made from hard plastic and attaches to a sturdy HDPE base.
This vacuum cup holder is quick and easy to mount. To install the holder make sure the mounting surface is clean and place the cup on your boat or vehicle then press the pump several times until the orange band disappears. To break the seal and remove the holder from your boat or vehicle simply pull the T-shaped tab up and towards the center of the cup. As suction decreases over time the plunger will extend from the cup. When the orange indicator band shows simply re-pump the plunger.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there, I'm Michael with etrailer.com. Today we're gonna take a quick look at this SeaSucker Fishing Rod Holder. This is going to free up your hands while you're fishing or if you're needing to bait your hook. This does have this four and a half inch vacuum cup. That's going to mount to most non-porous verticals surfaces. And when you see this, you might think of a suction cup something that you've used before in the shower something along those lines, but this is a vacuum cup.
So it is gonna give you a much stronger hold. You can see we do have this plunger here that we're going to push in on until that orange disappears. So it's going to attach in seconds. Just easily push in on that until that orange disappears, and that's gonna give us a nice strong hold. It's got a pull rating of 120 pounds, and then to remove it all we have to do is break that seal.
We'll pull up on the edge here, like so. And that's going to allow us to move it so that we can reposition it at a different angle if we need to or take it off if we want. So it is going to be a really convenient fishing rod holder for us. Very easy to get attached to your boats, gunnel or sidewalls, or to your vehicle to hold your fishing rod when you need your hands for other things. This does have a nice wide mouth that's going to accommodate most gimbal conventional rod sizes.
The bottom here you can see it is going to have this pin that we can remove. And so it can hold those long butt spinning reels, goes down through there. So a very nice option here for giving us some hands free time while we're out fishing. This does have a nice white, hard, plastic construction. So it is gonna be very lightweight yet very durable and only weighs about a pound and a half.
And so it's not gonna take much to put this out on your boat. Does come with a cap to put over top of that vacuum cup when we're not using it. We can store it away like that. And then when we're ready, just take that off put it wherever we need it and start sucking out that air with our vacuum pump. It is made here in the USA so you can trust it is gonna be a good quality material. It comes with a limited lifetime warranty. So, if you we're to have any problems with it you're more than welcome to reach out to us here at etrailer.com. But I think this is gonna be a really nice option for those of you who are looking for a single fishing rod holder. We do have other options that hold multiple fishing rods. So, if you've got multiple rods that you take out with you you might wanna take a look at that but if you just got the one this is gonna be a great bet for you. So completes our look for today. Again, I'm Michael with etrailer.com. Thanks for watching..
Average Customer Rating: 4.6 out of 5 stars (13 Customer Reviews)
This fishing rod holder mounts to your boat in seconds with a 4-1/2" vacuum cup. It attaches to most vertical, non-porous surfaces such as your boats' gunwales or sidewalls, or your vehicle while baiting your hook. Hard plastic construction.Works Great and love the strength holding trolling Poles.
Will be getting more
Seems good.
Just what I needed
Exactly as described and delivered promptly. I'll update when I install them on our boat.
The rod and gaff holder does a very good job. In rough seas at times it will fail but that isn’t often
Works well.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.